• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.358-361
• /
• 2004

This paper describes the development process of high stiffness body for ride and handling performance. High stiffness and light weight vehicle is a major target in the refinement of passenger cars to meet customers' contradictable requirements between ride and handling performance and fuel economy. This paper describes the analysis approach process for high stiffness body through the data level of body stiffness. According to the frequency band, we can suggest the design guideline about Is cornering static stiffness, torsional and lateral stiffness, body attachment stiffness. The ride and handling characteristic of a vehicle is significantly affected by vibration transferred to the body through the chassis mounting points from front and rear suspension. It is known that body attachment stiffness is an important factor of ride and handling performance improvement. And high stiffness helps to improve the flexibility of bushing rate tuning between Handling and road noise. It makes it possible to design the good handling performance vehicle at initial design stage and save vehicles to be used in tests by using mother car at initial design stage. These improvements can lead to shortening the time needed to develop better vehicles.

• 한국소음진동공학회논문집
• /
• 제20권10호
• /
• pp.931-939
• /
• 2010

A dash panel plays an important role to protect noise as well as heat. Meanwhile, it is also the most important path that transfers energy to the interior cavity, so that some of noises are transferred via air and its structural vibration becomes a major issue. From the viewpoint of NVH performance, simplified structures analogues to the dash wall are dealt with. Stiffeners, damping sheets and sound packages attached to a flat panel are taken into account as design variables. Structural radiation characteristics(thus, structure borne) such as radiation efficiency and radiation power are mainly discussed. For the case when an excitation is applied on a frame that surrounds the panel, it is shown that the radiation efficiency increases by attaching a stiffener to the panel, which is similarly found from the case when a panel is directly excited. It seems more effective to attach damping sheets along the boundary area of the panel rather than its middle area. The radiation efficiency of sound packages may make a dominant contribution to transmission loss as well as sound radiation. Experimental work was carried out to verify the results based on the simulation study.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권2호
• /
• pp.117-124
• /
• 2015

최근 생활수준의 향상으로 인해 가정용 에어컨의 보급률이 꾸준히 증가함에 따라 품질에 대한 소비자의 눈높이 또한 점점 높아지고 있다. 과거에 소비자의 요구는 제품의 효율성에 집중되었지만 점차 저진동/저소음에 대한 부분으로 확장되고 있다. 에어컨의 압축기는 제품의 효율을 결정하는 주요한 부분이면서 동시에 진동/소음의 주된 원인을 제공하고 있다. 압축기에서 발생한 진동/소음은 압축기 케이스와 배관을 통해 주위 구조물로 전달되고 이들은 다시 구조기인 소음이나 2 차적인 진동을 유발하게 된다. 본 연구에서는 RecurDyn 을 이용해 압축기의 진동/소음에 영향을 미치는 모터의 가진력이 고려된 MFBD(Multi Flexible Body Dynamics) 해석 모델을 개발하였다. 개발된 모델을 이용하여 압축기의 진동/소음 특성을 조사하고 압축기에서 발생하는 진동을 계산하여 실험 결과와 비교하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권2호
• /
• pp.21-34
• /
• 1988

Machinery enclosures are widely adopted to reduce the noise emission in various fields of application. Emitted noise, which is due to the vibration of enclosure's outer surface, is composed of two kinds of sound with different path of propagation. One is the "structure-borne sound", while the other is "air-borne sound". In order to get a most efficient machinery enclouser a prudent consideration upon the above structure-borne and air-borne sound is required, as the guiding principle of contermeasure for each noise is quite different. The controlling of input vibration and its isolation are major subjects for the structure-borne sound, and the specifications of absorbing members and damping panels are the major related matters for the air-borne sound. Hence, it seems very efficient to separate the total sounds into two categories with a great accuracy when one think of further reduction of noise from the existing enclosure, although its separating methods have not been made clear for many years. Author proposes an application method of experimental modal analysis to extract the structure-borne sound from the measured total radiation sound, as the air-borne sound is deduced by the vectorial difference between the measured total radiation sound and the calculated structure-borne sound. In order to calculate the correct structure-borne sound by the excitation at an arbitrary point on the enclosure structure, it is important to decide 1) how to estimate the enclosure's surface vibration velocity and 2) how to compute the radiation sound which is considered as the effect of vibration modes of enclosure surface. The former can be solved with total frequency response function calculated by the application of experimental modal analysis. The latter is to be solved by the author's new approaches for radiation sound computation by means of the Rayleigh's integral equation and the boundary-element method applied complex surface vibration velocity. As a first step, structure-borne sound by the excitation at an arbitry point on the rectangular plate with fixed edges, has been calculated to verified the reliability of the developed computation methods. The results of calculation show good agreements with those of the actual measurements.actual measurements.

• Journal of Astronomy and Space Sciences
• /
• 제25권4호
• /
• pp.491-504
• /
• 2008

태양센서는 인공위성의 자세제어에 필수적인 센서로서, 위성으로 입사되는 태양 빛의 방향을 측정하거나 위성이 태양을 보지 못하는 상태에 있는지를 판단하기 위해서 사용되고 있다. 이 논문에서는 저궤도 인공위성용 저정밀 태양센서의 성공적인 개발을 위하여, 비행모델 저정밀 태양센서를 개발하기 전에 태양센서 선행모델과 인증모델의 개발 과정 및 결과를 보여준다. 태양센서의 개발은 제작 특성상 공정의 명확성, 정밀성 그리고 많은 제작 경험을 필요로 한다. 이 논문에서는 선행모델과 인증모델을 개발함으로써, 공정의 명확성 및 정밀성을 갖도록 보완하였다. 따라서, 성능 요구 조건을 만족하는 결과를 얻을 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.667-671
• /
• 2012

Low frequency noises (up to about 200 Hz) mainly occur due to particular modes, resulting in booming noises, and in general the solutions may be found based on mode controls where conventional methods such as FEM can be used. However, at higher frequencies between 0.3~ 1 kHz, as the number of modes rapidly increase, radiation characteristics from structures, performances of damping sheets and sound packages may be more crucial rather than particular modes, and consequently the conventional FEM may be less practical in dealing with this kinds of structure-borne problems. In this context, so-called 'mid-frequency simulation model' based on FE-SEA hybrid method is studied and validated. Energy Transmission loss (i.e. air borne noise) is also studied. A dash panel component is chosen for this study, which is an important path that transfers both structure-borne and air borne energies into the cavity. Design modifications including structural modifications, attachment of damping sheets and application of different sound packages are taken into account and the corresponding noise characteristics are experimentally identified. It is found that the dash member behaves as a noise path. The damping sheet or sound packages have similar influences on both sound radiation and transmission loss. The comparison between experiments and simulations shows that this model could be used to predict the tendency of noise improvement.

• 대한기계학회논문집A
• /
• 제41권10호
• /
• pp.915-921
• /
• 2017

최근 자동차의 진동과 소음을 줄이기 위한 연구가 활발하게 이루어지고 있으나 기존의 연구들은 수동형 또는 능동형 마운트를 포함한 마운팅 시스템의 최적화에 대해서는 주목하지 않았다. 본 연구는 진동 소음원과 리시버 사이에 세 개의 구조적 경로를 가진 능동 마운팅 시스템에 대한 분석적인 연구를 수행하며 실제 시스템에의 적용 가능성을 확인한다. 능동 마운팅 시스템은 피에조 스택 액추에이터와 수동형 마운트가 커플링된 구조를 가지고 있다. 전체 시스템에 대한 동적 모델이 유도되고 각 경로의 스택 액추에이터 입력 힘과 위상이 각 경로의 완전한 절연을 타겟으로 하여 결정된다. 진동 저감 성능이 확인되고 이는 가장 좋은 저감을 가져오는 수동형 및 능동형 경로의 최적화된 결합을 제시한다.

• 한국소음진동공학회논문집
• /
• 제20권11호
• /
• pp.1018-1024
• /
• 2010

The printer noise consists of the noise of the various components and parts such as motor, fan and solenoid. And the human's printing sound recognition shows various aspects when the printer starts to print papers because the components operate at the same time. Especially, printers are usually installed in the quiet office room. Therefore the printing noise is related to its competitiveness in the market. The importance of the printer sound qualities is increasing and it is necessary to develop the sound quality evaluation system, so it is a key point to identify the noise source of the printer and develop the sound quality index to each component. By using this evaluation system, it is possible to evaluate the sound quality of a prototype printer compared to the already existing one. In this paper, the printer sound quality evaluation system was developed by the following steps. Firstly, the signal processing method was applied to the recorded printing sound to identity and split the noise of components. Secondly, the MLR(multiple linear regression) method and the psychoacoustics were used to develop the sound quality index. Finally, the improvement of the printer sound quality is possible by using the result of the MLR and the path analysis. The output of this research will be applied to the development of a new printer.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.788-791
• /
• 2005

Nodal displacements are referred to the Initial configuration in the total Lagrangian formulation and to the last converged configuration in the updated Lagrangian formulation. This research proposes a relative nodal displacement method to represent the position and orientation for a node in truss structures. Since the proposed method measures the relative nodal displacements relative to its adjacent nodal reference frame, they are still small for a truss structure undergoing large deformations for the small size elements. As a consequence, element formulations developed under the small deformation assumption are still valid fer structures undergoing large deformations, which significantly simplifies the equations of equilibrium. A structural system is represented by a graph to systematically develop the governing equations of equilibrium for general systems. A node and an element are represented by a node and an edge in graph representation, respectively. Closed loops are opened to form a spanning tree by cutting edges. Two computational sequences are defined in the graph representation. One is the forward path sequence that is used to recover the Cartesian nodal displacements from relative nodal displacements and traverses a graph from the base node towards the terminal nodes. The other is the backward path sequence that is used to recover the nodal forces in the relative coordinate system from the known nodal forces in the absolute coordinate system and traverses from the terminal nodes towards the base node. One closed loop structure undergoing large deformations is analyzed to demonstrate the efficiency and validity of the proposed method.

• 터널과지하공간
• /
• 제29권3호
• /
• pp.135-147
• /
• 2019

본 논문은 기계시스템의 하중추정 기법 및 적용사례 소개가 목적이다. 이를 위해 진동기반 하중추정 기법의 이론적 배경 및 하중정량화 절차를 구체적으로 설명하였다. 또한 충격하중 및 진동이 발생하는 천공장비에 적용하여 진동기반 하중추정 기법의 적용성과 한계점을 분석하고 이에 대한 대응책에 대해 논의하였다. 마지막으로, 하중추정 기술의 추가 연구의 필요성을 토의하고, 새로운 충격하중 측정기술 개발을 위한 방법론을 제안하였다.