• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.670-675
• /
• 2003

With the increase in recording density and higher rotation speeds, the aerodynamic aspect of hard disk drives (HDDs) is now quite significant. To achieve high TPI (tracks per inch) for hard disk drives, the actuator must induce less air turbulence. Also, alternative cross sections for the actuator arms are proposed for the reduction of air turbulence. In this study, off-track vibration of actuator arms used in of 3.5" hard disk drives with different cross sections have been measured by using Laser Doppler Vibrometer (LDV). It has been found that the vibration of the actuator arms with modified cross sections is lower than the conventional one.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.102-107
• /
• 2012

In this study, the design procedure of hybrid active mount by an electro-magnetic actuator is proposed to reduce the transmitted force from naval shipboard equipment to ship hull structure. The hybrid type mount which is composed of a passive rubber element and an electro-magnetic actuator is introduced and, through the vibration measurement for the objective pump system, the required force of the actuator is computed and discussed in detail. The initial designs were supposed for three types, one is moving coil type actuator and the others are moving permanent magnet type actuators. Based on the initial design concept, the final designs considering shock resistance and interference with mover and stator are proposed and examined.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1071-1076
• /
• 2008

This paper presents the self power generation from vibration using the piezoelectric bimorph actuator. The piezoelectric bimorph actuator was well developed with PZT-PNN-Fe piezoelectric ceramics. As the applied voltage was increased, a linear change of displacement was obtained with a relatively high ratio of 12.53 um/V for the bimorph actuator. Moreover, when the motor's rotational speed was 2000 rpm, the bimorph actuator, which has a resonance frequency of 68 Hz, exhibited the most efficient generation voltage of 10.4 V. This bimorph actuator could make the LED, emitting 60 mW, working successfully. Therefore, it is anticipated that the bimorph actuator will be useful as a power source for the next-generation electronic devices.

• Journal of Mechanical Science and Technology
• /
• v.17 no.11
• /
• pp.1616-1627
• /
• 2003

This paper describes a mini linear optical pickup actuator. To reduce the size, inner yokes are designed to guide the mover and outer yokes of permanent magnets are removed. Magnetic circuit method is used to determine the thrust force. Virtual path method is proposed to analyze the open magnetic circuit analysis. The magnetic circuit of the proposed actuator can be a closed circuit due to the virtual path model of the outer magnetic flux. The validity of virtual path method is evaluated by comparing to the FEM analysis. Structural vibration is investigated using FEM and the design of the mover is modified to improve the vibration characteristic. Dynamic characteristic experiments shows that the performance of the proposed actuator is enough to be used as a coarse and fine seeking actuator simultaneously and the thrust force margin for loading a focusing actuator is guaranteed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.565-569
• /
• 2002

To improve the driving sensitivity of an optical pickup actuator for high density and high speed drive, we present a new actuator design using multipolar flux-density distribution by magnetic materials and Nd-Fe-B sintered magnets. We expect this actuator to use in 3-axis actuator for tilt compensation as well as conventional 2-axis actuator. The electromagnetic field analysis applying 3-D FEM was performed and several samples were actually tested. From comparing simulated data with experimental results, we verified the accuracy of the simulation and the superiority of the presented method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.234-238
• /
• 2003

Ultra small optical drive or PCMCIA type needs a focusing actuator because or applying Blue Laser and enhancing compatibility according to disk physical specification. Based on this need, this paper presents a novel focusing actuator adapted for ultra small optical drive of PCMCIA type. The focusing actuator using Lorenz force generated consists of coil, magnets and plate springs of pivoting. The design issues of the focusing actuator are the flexibility to focus direction, the rigidity to track direction and the higher natural mode of the moving part. For settling these Issues, this paper present mechanical design, computer simulations and test results of the realized focusing actuator. Finally, suitability and usefulness of the focusing actuator was demonstrated by the comparison of simulations and test results in a view of the possibility adapted for ultra small optical drive.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.592-596
• /
• 2001

Near field technology makes it possible to overcome the diffraction limit of laser beam and create the small spot. Because of the small spot size, the pit size and track pitch can be decreased. So the high performance actuator is needed for near field recording system. And the light mass and the small form factor are also important properties of the NFR actuator in order to be used for hand held device. The purpose of this paper is the optimal design of the NFR coarse actuator to maximize actuating force. The structure of NFR coarse actuator is the same as HDD VCM actuator. The permeance method is used for modeling of the coarse actuator. The optimal result and the FEM simulation result are presented.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.261-266
• /
• 1998

In this study, the in-situ parameter identification method for active magnetic bearing (AMB) actuator based on an open-loop balancing scheme is proposed. The scheme utilizes the relation between the compensating voltage and the known unbalance force. Main advantage of this method is that it is easy to use, yet it gives the actuator dynamics on the actual operating condition of an AMB system. The experimental results show that the proposed scheme compensates the known unbalance accurately and consequently identifies the actuator dynamics effectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.911-914
• /
• 2003

As high-capacity disk drives pow in track density, the allowable level of PES is becoming smaller. In this paper, some design concept of actuator is introduced to suppress the Butterfly mode that imposes the fundamental limitation on servo bandwidth. The effect of dynamics of proposed actuator on PES is examined by simulation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.11 s.104
• /
• pp.1276-1286
• /
• 2005

In this paper, the dual stage interaction between the coarse actuator and the fine actuator of an optical disk drive is studied, and the new control method to enhance the track pull-in performance using fine actuator control is proposed. First, the dynamic analysis for the dual stage and the experiments to find the each actuator dynamics are performed. From the experiments, some physical parameters of the actuators were derived, then, some simulations are performed to find the interaction effect of the fine actuator during seek motion. Second, the center servo which suppresses the vibration of fine actuator during seek motion is designed and evaluated. And the fine actuator control to reduce the relative velocity between the target track and beam spot is proposed. From simulations, we show that fine actuator control which has same frequency and same phase of the disturbance is effective to reduce the relative velocity, and this result leads to track pull-in enhancement. Hence, the proposed control method is good approach to improve the track pull-in performance. Finally, the realization of the proposed method and some comments of it are briefly discussed.