• Journal of Environmental Impact Assessment
• /
• v.22 no.4
• /
• pp.381-387
• /
• 2013

In order to improve the environmental vibration, it is necessary to method for not only reduce the vibration source, but also control the vibration path. In this study, we used borebole for estimate the vibration reduction. And also, we analyzed displacement and vibration velocity caused by the position of borehole as well as the condition of borehole in ground structure. Visual FEA(Finite Element Analysis) program was used in this numerical analysis. The results are as follows : The displacement magnitude and X, Y direction displacement were represented to different results due to the condition and position of borehole, and were represented to the lowest values when the position of borehole is the most close condition from the vibration source. And also, the vibration velocity was decreased as using borebole in ground structure. The isolation efficiency of the vibration was calculated to maximum 18.40% when borehole was established to the most close position from the vibration source and the receive point.

• Selected Papers of The Society of Naval Architects of Korea
• /
• v.2 no.1
• /
• pp.18-28
• /
• 1994

In the vibration analysis of submerged or floating bodies such as ships and offshore structures, the coupled system between fluid and structure should be considered using the compatibility conditions on the wetted surface. It is well known that the hydroelastic vibration analysis of structures in contact with fluid can be done by applying the finite element method(FEM) to structures and the boundary element method(BEM) to the fluid domain. However, such an approach is impractical due to the characteristics of the fully coupled added mass matrix of fluid on the entire wetted surface. To overcome this difficulty, an efficient approach based on a reanalysis scheme is proposed in this paper. The proposed method can be applied for cases of higher local modes and beam-like modes for which three-dimensional reduction factors are not known. The three dimensional reduction factors are not needled and thus the restrictions can be removed in the analyses of non-beam like modes or local vibration modes by considering fluid-structure interaction. The validity and calculation efficiency of the proposed method are proved through numerical examples.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.78-82
• /
• 2006

Recently, The demands for the reduction of noise generated by transformers have been increasing. Almost all of the noise generated by transformers is a result of magnetostricitive vibration in the core. The noise radiates into the atmosphere from the tank through the insulation oil. As the noise of transformer irritates residents, needs for decreasing the noise of transformer have been arised. One method of reduction such a noise is to build a free-standing enclosure of concrete and steel plates around the transformer. However, this method has some disadvantages. Another method of noise reduction is to mount a close-fitting sound insulation panel on the side of a transformer tank. Side plate vibrations of transformer are transmitted to such a sound insulation panel along two paths. In one case, they are transmitted through air by sound pressure and in the other through supporting structures. In the paper, the vibration and noise effect which is transferred from reinforce channel to insulation panel generated by transformer have been identified for the several kinds of insulation panel and damping sheet analytically and experimetally.

• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.401-408
• /
• 1999

A method is presented for the vibration analysis of steam turbine-generator rotor system based on the component mode synthesis method. The motion of each component of the system is described by superposing constraint mode associated with boundary coordinates and constrained normal modes associated with internal coordinates. This method using real fixed-interface modes allows for significant reduction in system model size while retaining the essential dynamic characteristics of the lower modes. The capability of this method is demonstrated in the natural frequency and unbalance response analysis of the steam turbine-generator rotor system in which the dynamics of the pedestal is considered. The results by the present method are compared with finite element method and trnasfer matrix method in terms of the accuracy and computing time.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.181-188
• /
• 2000

Input shaping is a method fur reducing residual vibration. Vibration is eliminated by convolving an input shaper, which is a sequence of impulses, with the desired system command. It has been applied to robot with a flexible manipulator. But it can be applied to the reduction of residual vibration far overhead crane. In this paper, input shaping shows good performance for anti-sway of overhead crane. In the z-domain, we designed an input shaper and calculated the sensitivity of it. If sensitivity is calculated in the z-domain, the shapes of sensitivity curves are expected easily. Accordingly, it is easy to design an input shaper in the z-domain. We compared the response of a system with shaper to it without that. Also, we compared El shaper to ZV shaper in view of robustness.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.6
• /
• pp.546-552
• /
• 2011

In this study, noise sources of a reducer which is combined a spiral bevel gear and a planocentric gear are identified by experimental method and the noise was reduced by the structure modification of the reducer. In order to identify the noise sources, noise and vibration signals were measured by microphone and accelerometer and these signals were analyzed with waterfall plot. In addition, the frequency response functions were obtained to prove the noise and vibration sources. It was found that the resonance was generated by the gear mesh frequencies and natural frequency of the reducer. The noise of the reducer could be reduced by structure modification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.51-56
• /
• 2011

In this study, noise sources of a reducer which is combined a spiral bevel gear and a planocentric gear are identified by experimental method and the noise was reduced by the structure modification of the reducer. In order to identify the noise sources, noise and vibration signals were measured by microphone and accelerometer and these signals were analyzed with waterfall plot. In addition, the frequency response functions were obtained to prove the noise and vibration sources. It was found that the resonance was generated by the gear mesh frequencies and natural frequency of the reducer. The noise of the reducer could be reduced by structure modification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.916-921
• /
• 2014

In this paper, an improved small-scaled blade prototype was designed with the flap-driving mechanism classified as an active vibration reduction method, in order to reduce vibratory load in the helicopter. In detail, the previous Active Trailing-Edge Flap based on piezoelectric actuator, called SNUF(Seoul National University Flap), failed to achieve the target value (${\pm}4^{\circ}$) of the flap deflection angle. Therefore, the flap-driving mechanism design was improved, and a new piezoactuator was selected to accomplish the target value of the flap deflection angle in both static and rotating situations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.137-142
• /
• 2004

The aim of this study is to investigate the characteristics and quantity of the noise reduction by floor coverings. The characteristics on the reduction of the lightweight impact sound level by floor coverings is as follows. The insulation level attained by floor coverings tends to be smaller in actual buildings than in public laboratories. The reduction of the impact sound level to the tape is similar to the method of adhesives. For this reason, the reduction of impact sound level by floor coverings in public laboratories can be utilized to tape. And the reduction of impact sound level by floor coverings is not influenced by the size of specimen except the specific frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1370-1375
• /
• 2001

Substructure coupling or component mode synthesis may be employed in the solution of dynamic problems for structure. The model is partitioned into several subdomains. and a generalized Craig-Bampton representation is derived. In this paper the mode sets(normal modes. constraint modes) have been employed for model reduction. A generalized model reduction procedure has been described. Those reduction methods which adapt constraint modes have been described in detail. As examples. a flexible structure and a 10 DOF damped system are analyzed. Comparison with a conventional reduction method based on a complete model has been made via eigenpairs and dynamic responses.