• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.213-216
• /
• 2009

가스터빈 연소기의 화염 특성을 알기 위하여 분할 연소기 시험을 수행하였다. 점화시험은 여러 가지 연소기 유입 공기속도와 공기과잉율에 따라 토치 점화장치를 이용하여 수행되었다. 또한, 연료를 충분히 공급한 상태에서 점화를 수행한 후 점차 연료량을 감소시켜가며 희박연소한계를 측정 하였다. 실험 결과, 공기과잉율 6에서 안정한 점화를 보였고 이 값은 연소기 공기 유입속도에 따라 점점 증가함을 보였다. 최소 실화한계는 연소기 공기 유입속도 40 m/s에서 약 4였고, 이 값 또한 연소기공기유입속도에 따라 약 10 까지 증가함을 보였다.

• 설비공학논문집
• /
• 제16권5호
• /
• pp.397-407
• /
• 2004

It is well known that some key parameters, such as evaporating temperature, refrigerant mass flow rate, face velocity and inlet air temperature, have significant influence on the evaporator performance. However performance studies related to a humid environment have been very scarce. It is demonstrated that the refrigerant mass flow rate, heat flux, water condensing rate and air outlet temperature of the evaporator significantly increase with air inlet relative humidity. As the air inlet relative humidity increases, the latent and total heat transfer rates increase, but the sensible heat transfer rate decreases. The purpose of this study is to provide experimental data on the effect of air inlet relative humidity on the air and refrigerant side pressure drop characteristics for a slit fin-tube heat exchanger. Experiments were carried out under the conditions of inlet refrigerant saturation temperature of 7 $^{\circ}C$ and mass flux varied from 150 to 250 kg/$m^2$s. The condition of air was dry bulb temperature of 27$^{\circ}C$, air Velocity Varied from 0.38 to 1.6 m/s. Experiments Showed that air Velocity decreased 8.7% on 50% of relative humidity 40% of that at degree of superheat of 5$^{\circ}C$, which resulted that pressure drop of air and refrigerant was decreased 20.8 and 8.3% for 50% of relative humidity as compared to 40%, respectively.

• 상하수도학회지
• /
• 제27권2호
• /
• pp.215-222
• /
• 2013

The fluctuation of inlet flow to a water treatment plant makes a serious problem that it can change the outlet flowrate from each process abruptly. Since it takes very short time for the surface wave occurred from the fluctuation of inlet flow to reach the latter processes, it is impossible for operators to cope with that stably. In order to investigate the characteristics of hydraulic behavior for rectangular sedimentation basin in water treatment plant, CFD(Computational Fluid Dynamics) simulation were employed. From the results of both CFD simulations, it was confirmed that time taken for the follow-up processes by the fluctuation in intake well can be estimated by the propagation velocity of surface waves. Also, it takes very short time for the surface wave occurred from the fluctuation of inlet flow to reach the latter processes. In the case of inlet flowerate being increased sharply, local velocity within sedimentation basin appeared as wave pattern and increased due to convection current. Also, it could be observed that vortex made local velocity in the vicinity of bottom rise.

• 한국전산유체공학회지
• /
• 제3권2호
• /
• pp.52-64
• /
• 1998

Numerical simulations on the flowfield of lifting chamber for Wing-In-Ground vehicle were performed using Fluent/UNS 4.2 software. The trend of lifting force in lifting chamber and parametric study of geometric and fluid variables were primarily investigated. Selected parameters for investigation are inlet velocity, height between chamber and water level, depth of the skirt, location of inlet, variaton of height at bow and stern. Also, air capturing capabilities from downstream of the propeller were evaluated at the air inlet. The lifting force was increased linearly with the increased of inlet velocity and nonlinearly with the decrease of height force was increased with increased depth. It turned out to have very minor effect on lifting force to change the location of air inlet for lifting chamber, installed on top surface. Tilting the vehicle when it was lifted, the lifting forces, generated in each case, showed no appreciable changes.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1172-1177
• /
• 2008

Diverging channel from gas burner exit to the inlet section of Heat Recovery Steam Generator (HRSG) has been re-designed for 1 MW steam supply and power generation system. Three different test geometries have been chosen for the numerical simulation. The existing design for 300 kW HRSG system (CASE B) has been improved by geometry and position changes of inlet guide vanes along with gas velocity entrance angle at the diverging channel inlet (CASE C). Both cases has been compared with the case where hot combustion gas is directly injected without any guide vanes (CASE A). Improved design shows overall uniform velocity and temperature distribution compared to existing design.

• 대한기계학회논문집B
• /
• 제40권1호
• /
• pp.9-19
• /
• 2016

본 연구는 테일러 반응기내 각속도와 유입속도 변화에 따른 테일러 유동의 변화와 입자의 체류시간 변화를 전산수치해석 기법을 이용하여 알아보았다. 반응기내 유동은 각속도가 증가함에 따라 점점 불안정해지는 경향을 보였다. 유동은 레이놀즈 수의 증가에 따라 CCF, TVF, WVF, MWVF 영역으로 이동하게 되고 각 영역에서 상이한 유동특성을 보였다. 유입속도의 변화가 테일러 유동에 영향을 주는 것을 확인하였다. 각속도가 빠를수록, 그리고 유입속도가 느릴수록 입자의 체류시간과 표준편차는 증가하였다.

• Journal of Biosystems Engineering
• /
• 제9권1호
• /
• pp.22-33
• /
• 1984

Husk separator is an indispensable equipment in rice milling plants. However, any basic research on the designing and operating criteria of the husk separator have rarely been conducted in Korea. According to the survey results reported recently, grain loss occurs in the process of rice husk separation at custom rice milling plants in Korea and the performance of husk separator has also not been identified. With this regard this study was conducted with a typical commercial husk separator to investigate the effect of the operational factors such as feed rate, blower speed and opening ratio on the velocity distribution in the air duct and the performance of the separator. The results are summerized as follows: 1. The average wind velocity in the primary air duct increased linearly with the blower rpm and the size of air inlet port in both cases of double type and single type operations. 2. The coefficient of variation in the horizontal wind velocities in the primary air duct was the minimum when the opening ratio was 0.22 ($0.052m^2$ of air inlet port) in both cases of single type and double type operations regardless of the blower speeds used in this test. The average wind velocity at the upper part of air duct was greater by 2-5 m/s than the velocity at the bottom part in double type operation. In case of single type operation, however, the average velocity in the middle part was greater than the upper or bottom part when the opening ratio was greater than 0.74. 3. The relationship between the overall effectiveness of separation(Ed for double type and Es for single type) and the average wind velocity (Va) in the primary air duct was expressed in the following quadratic functions. $$Ed=-190.84+106.18Va-10.052Va^2$$ ($r^2$ = 0.97782) $$Es=-223.76+106.23Va-9.1935Va^2$$ ($r^2$ = 0.97029) The average wind velocity required to obtain the overall effectiveness of separation more than 80% ranged from 4.04 m/sec to 5.84 m/sec in case of double type operation, and from 4.70 m/sec to 6.20 m/sec in case of single type. 4. An optimum wind velocity can be obtained with an increase in the blower speed or the size of air inlet port as presented in Figure 8. There was a tendency that the faster the blower speed, the narrower the control range of the air inlet port. 5. The feed rates (1850kg/hr and 2100kg/hr) adopted in this experiment did not bring about a significant difference in both the overall effectiveness of separation and the power consumption. 6. The energy consumption increased cubically with the blower speed but linearly with the size of the air inlet port. On the basis of the results described in items 1, 3, and 6, it would be more economic to adjust the size of the air inlet port larger with a relatively low blower speed than to adjust the size smaller with a relatively high speed.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.88-96
• /
• 2008

Effects of the duct inlet guide vane on the flowrate distribution characteristics of the defroster nozzle exit in a defrost duct system were investigated experimentally to design the optimum heating, ventilation and air conditioning (HVAC) system applied in an automotive compartment. A 3-dimensional hot-wire anemometer system was used to measure the velocity field in the vicinity of the defroster nozzle jet flow and the velocity distributions near the windshield interior surface. At first, two cases of with- and without-duct inlet guide vanes were considered as the test condition, and then three cases of the duct inlet guide vane were tested to determine the optimum guide vane shape and their positions. The arrangement of the duct inlet guide vanes has an effect on the improved flowrate distribution at the defroster nozzle exit and near the windshield interior surface. However, the application of the lots of guide vane to control the flow direction leads to increase the flow resistance, resulting in the decreased flowrate issuing from the defroster nozzle. The shape of the duct inlet guide vane affects not only the flowrate distribution between the driver side and the assistant driver side but also the reduction of the flow resistance in the defrost duct system.

• 멤브레인
• /
• 제22권5호
• /
• pp.369-380
• /
• 2012

본 연구에서는 직접 접촉식 막증류 공정에서 운전인자에 따른 담수 투과량과 열효율을 예측하기 위해 열 및 물질전달 방정식을 이용하여 1차원 해석모델을 개발하였다. 이 해석모델의 타당성을 검증하기 위해 해석모델 결과와 기존 연구자들에 의해 수행된 실험 결과를 비교하였고 만족할 만한 결과를 얻었다. 이를 통해 DCMD 모듈에서 염수와 증류수의 입구온도 및 입구속도가 담수 투과량 및 열효율에 미치는 영향을 분석하였다. 그 결과 염수의 입구온도와 입구속도가 증류수의 입구온도와 입구속도보다 담수 투과량과 열효율 증가에 미치는 영향이 크기 때문에 지배적인 운전특성이라는 것을 알 수 있었다. 염수의 입구온도가 $60^{\circ}C$에서 $95^{\circ}C$로 증가할 때 담수 투과량이 21.22 $kg/m^2h$에서 71.26 $kg/m^2h$로 3.4배 증가하였고 열효율은 0.556에서 0.765로 37.5% 증가하였다. 한편, 염수의 입구속도가 60에서 300 m/h로 증가함에 따라 담수 투과량이 27.91 $kg/m^2h$에서 36.33 $kg/m^2h$로 30% 증가하였고 열효율은 0.6에서 0.646로 7.5% 증가함을 알 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1969-1974
• /
• 2004

The performance of small cyclone is analysed by an experiment for the purpose of developing a bag-less vacuum cleaner. For the high collection efficiency and low pressure loss cyclone, the effect of cyclone inlet feature must be well understood. Four types of the helical inlet are considered to compare with the normal tangential inlet, and also various inlet velocities are used to each inlet type. Based on the reference dimension, each type of inlet shows the changes of the grade efficiency and pressure loss which determine the cyclone quality. The results show that the helical inlet has the smaller cut-size but bigger pressure loss than the tangential inlet. And the degree of opening area influences factors of cyclone performance. As the inlet velocity is increased, the cut-size becomes smaller and the pressure loss becomes bigger of each cyclone. Further studies are required to understand the optimized helical inlet of cyclone.