• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.133-135
• /
• 2006

This paper considers a speed control problem of DC motor under load variations. In order to reduce the effect of load variation, a disturbance observer has been designed for the given system. With a cheap encoder there exists considerable measurement noise in the velocity feedback and it should be reflected in designing the disturbance observer. The authors have obtained the nominal transfer function of a DC motor and designed a disturbance observer for the control purpose. With the disturbance observer a digital controller has been implemented using a DSP(TMS320F2812). Some experiments show the enhanced performance of the control system with the proposed method.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.130-135
• /
• 1998

This paper deals with a position control problem of a hydraulic proportional position control system using a friction compensation control. There are many nonlinearities in hydraulic systems. With only proportional controller, response is slow and steady-state error cannot be compensated properly. Controller designed in this paper achieves fast transient response through the velocity and acceleration feedback and good steady-state response through the friction compensator. A/D and D/A board is employed for data acquisition and manipulation. The experimental results are compared with computer simulation results using Matlab.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.90-98
• /
• 1997

A time-optimal control law for quick, strongly nonlinear systems has been developed and demonstrated. This procedure involves the utilzation of neural networks as state feedback controllers that learn the time-optimal control actions by means of an iterative minimization of both the final time and the final state error for the systems with constrained inputs and/or states. A neural identifier or a genetic algorithm identifier could be utilized for modeling the partially known systems and the unknown systems. The nature of neural networks as a parallel processor would circumvent the problem of "curwe of dimensionality". The control law has been demonstrated for both a torque input motor and a velocity input motor identified by a genetic algorithm called GENOCOPed GENOCOP.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.950-957
• /
• 2003

This paper deals with adaptive fuzzy logic controller design to achieve proper dynamic response of a composite thin-walled beam with a tip mass. In order to check the effectiveness of this controller, three different types of control logic are selected and applied. The adaptive control capabilities provided by a system of piezoactuators bonded or embedded into the structure are also implemented in the system. Results show that the fuzzy logic controller is more effective than the proportional or velocity feedback controller for the vibration control of composit thin-walled beam with a tip mass.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.105-108
• /
• 1988

In this paper, a control system design method is proposed for DC motor drive. A state space model is used to control sysytem and for closed loop system the technique of pole assignment is applied. The control system is designed with state feedback theory and to improve the response further more feedforward theory is applied to control system. The microprocessor as a controller and the interfaces in the system are proposed. Digital simulation results for step changes in reference velocity and load torque are shown.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.424-428
• /
• 2004

A wind turbine system converts wind energy into electric energy, the system operated under normal environmental conditions. In case of particular turbulent wind flow such as typhoon, hurricane etc, the control of a blade used to a yaw control and a pitch control method. A small wind turbine has not a speed control system to only a manual tail safety brake. This paper shows a automatic tail safety brake controller based on feedback control using wind velocity. The controller composed of wired motor, relay system, steel wired motor him down a perpendicular to wind flow and then the blade speed reduced high to zero. The operation of automatic tail safety controller verified by manual test.

• 한국소음진동공학회논문집
• /
• 제11권6호
• /
• pp.193-199
• /
• 2001

Active control of forced vibration of the cantilevered laminated composite plates using collocated piezoceramic sensor/actuator is analyzed numerically and verified experimentally for various fiber orientations. Impact on the stiffness and the damping properties is studied by varying stacking sequence of [$\theta$$_{4}$O$_{2}$90$_{2}$]s for the laminated composite plate. For the forced vibration control, the plate is excited by one pair of collocated PZT exciters in resonance and its vibrational response is suppressed by the other collocated PZT sensor/actuator using direct negative velocity feedback. It is shown that the active control of forced vibration is more effective for the smart laminated plate with higher modal damped stiffness(2ζ$\omega$/aup 2/) .

• 대한물리의학회지
• /
• 제12권3호
• /
• pp.67-71
• /
• 2017

PURPOSE: Muscle fatigue is a cause to change proprioception. The purpose of this study was to investigate the effects of calf muscle fatigue and visual control on postural balance during single-legged standing in healthy adults. METHODS: Nineteen healthy adults (male) were participated in this study (mean age: 24.36 years; mean height: 171.32 cm; mean weight: 64.58 kg). The postural balance (sway length, sway area, sway velocity of COG displacement) was measured by Balance Trainer System (BT4) in before and after calf muscle fatigue feeling in single legged stance. In this study, repetitive single-legged heel rise test was used to induce fatigue of the calf muscle. Paired t- test was used to compare the postural balance between before and after calf muscle fatigue. Data of subjects were analyzed using SPSS 22.0 (SPSS Inc., Chicago, IL, USA). Level of significance was set to .05. RESULTS: The sway length, sway area, sway velocity of COG (center of gravity) displacement after calf muscle fatigue feeling was significantly increased compared to before calf muscle fatigue feeling during single leg standing both eye open and close conditions (p<.05). CONCLUSION: This study suggested that calf muscle fatigue feeling has affected on postural balance when standing one leg both eye open and close conditions and postural control was disturbed by muscle fatigue and visual feedback in single leg standing.

• 한국산학기술학회논문지
• /
• 제5권3호
• /
• pp.266-272
• /
• 2004

본 논문에서는 주행 차량의 직진운동 제어를 위하여 관측자를 이용한 적응제어기를 제안한다. 차체중량, 시정수 등의 차량 파라미터들을 추정하기 위해 표준형 적응칙을 이용한다. 차량의 구동력 입력에서 가속도 까지의 비선형 모델을 이용하여 차량주행 속도 및 가속도 관측자를 설계한다. 제안한 관측자의 지수함수적인 안정도 및 관측자에 의거하여 설계한 적응제어기의 안정도를 리아프노브 함수 후보에 의해 입증한다. 전체 시스템의 안정도 및 차차간 상대거리/속도/가속도 오차들의 점근적인 수렴성도 수학적으로 입증하며, 제안한 방법의 타당성 및 효율성을 시뮬레이션을 통해 검증한다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 추계종합학술대회
• /
• pp.701-704
• /
• 2005

PID 제어기는 구조가 간단하고 적용이 용이하다는 장점으로 인하여 널리 사용되고 있는 제어방식이다. 이러한 선형 PID 제어기는 시스템의 파라메터가 변화가 있거나 부하 특성이 비선형적으로 변화할 때에 적절한 이득과 성능을 얻기 어려워 고성능 제어 특성을 기대하기 어렵다. 본 연구에서는 세포성 면역 반응과 경사감소학습에 기초하여 비선형 PID 제어기를 설계하고, 설계된 제어기의 이득과 비선형 함수의 파라메터들을 실시간 적응적으로 학습할 수 있는 학습 알고리즘을 개발하고, 이를 제어시스템에 적용하였다. 제안된 비선형 PID 제어기는 비선형 직류 모터 시스템의 파라메터들이 변화하거나 주파수가 다른 추종 명령에 대하여, 적응적으로 이득을 변화 시키며 추종함을 보였다.