• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1853-1857
• /
• 2005

In most of motor-driven motion control systems, an encoder is used to measure a position of the motor and the velocity information is obtained by measuring the position increment over a sampling period. The quantization effect due to limited resolution of the encoder induces some measurement errors, and consequently causes deterioration of the motion performance especially in low velocity. In this paper, we propose a gain-scheduled acceleration estimator which works in wider velocity range than the original acceleration estimator. We investigate and analyze characteristics of the velocity measurement mechanism which takes into account the quantization effect of the encoder. Next, we introduce the acceleration estimator and propose a gain-scheduled acceleration estimator. The bandwidth of the gain-scheduled acceleration estimator is automatically adjusted by the velocity command. Finally, its performance is evaluated by simulation and experiment, and the results are compared with those of a conventional method and the original acceleration estimator.

• 한국지능시스템학회논문지
• /
• 제21권3호
• /
• pp.283-289
• /
• 2011

본 논문에서는 차륜형 역진자에 적용되는 속도 추정기 기반 제어기 설계와 다양한 수치 시뮬레이션이 수행되었다. 차륜형 역진자는 불안정한 평형점과 안정한 평형점을 동시에 갖는다. 불안정한 평형점에 대하여 평형을 유지하기 위하여 차륜형 역진자는 지속적으로 제어되어야 한다. 제어기의 입력으로 차륜형 역진자 몸체의 각도, 각속도, 변위 속도 등이 필요하다. 필요한 속도는 모터에 부착된 에코더 신호를 차분하여 얻어지며, 엔코더의 해상도에 민감하게 의존한다. 저해상도 엔코더와 속도 추정기에 기반하여 개선된 속도 검출법이 제안되고 경사면에서 유효함을 보이기 위해서 다양한 수치 시뮬레이션이 수행되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.140-142
• /
• 2007

This paper presents an effective method of precise velocity control at low speed with a low resolution encoder. Multirate observer to estimate the velocity at every DSP control period is used except a constant velocity mode. The observer corrects the estimation error when detects pulse signal. Unlike the conventional methods, the multirate estimator is stable at a low speed. However, the multirate estimator shows ripples at a constant velocity. Thus, in this paper we use a velocity prediction method which uses the present velocity from the previous average velocity to reject the ripple. In a summary, at a constant speed mode, the predicted velocity is used. Otherwise, the estimated velocity by the multirate obvserver is used. The effectiveness of the multirate observer and ripple rejection at low speed is verified through various simulations.

• 한국정밀공학회지
• /
• 제8권3호
• /
• pp.64-72
• /
• 1991

This paper deals with the state estimator and controller. All state variables' feedback in the system were used to improve electro hydraulic servo sysem were used to improve electro hydraulic servo system's responese charact- eristics. Many gains of the state variables'and estimator's are produced by the algebraic Riccati equation, and every state variables'optimal gain and estimator gain is selected by trial and error method. For the designed estimator performance's examination, this paper simulate the time response for the step input, the reduced velocity output in subjected to load torque, and the time response for the step input in changing the inertiamoment.

• 전기학회논문지
• /
• 제65권11호
• /
• pp.1868-1878
• /
• 2016

This paper proposes a novel velocity estimator for long-term underwater navigation of autonomous underwater vehicles(AUVs). Provided that an external position fix is not given, a viable goal in designing a underwater navigation algorithm is to reduce the divergence rate of position error only using the sporadic velocity information obtained from Doppler velocity log(DVL). For such case, the performance of underwater navigation eventually depends on accuracy and reliability of external velocity information. This motivates us to devise a velocity estimator which can drastically enhance the navigation performance even when the DVL measurement is unavailable. Incorporating the Gertler-Hagen hydrodynamics model of an AUV with the measurement models of velocity and depth sensors, the velocity estimator design problem is resolved using the extended Kalman filter. Different from the existing methods in which an AUV simulator is regarded as a virtual sensor, our approach is less sensitive to the model uncertainty often encountered in practice. This is because our velocity filter estimates the simulator errors with sensor aids and furthermore compensates these errors based on the indirect feedforward manner. Through the simulations for typical AUV navigation scenarios, the effectiveness of the proposed scheme is demonstrated.

• Transactions on Control, Automation and Systems Engineering
• /
• 제2권4호
• /
• pp.228-234
• /
• 2000

The aim of the work is to present a new method of estimating the existence of a mass unbalance and mass unbalance under a crack on a rotating shaft. This is an advanced new method for the detection of a mass unbalance and a new way to estimate the position of it under crack influence. As the first step, the shaft is physically modelled with a finite element method and the dynamic mathematical model is derived by using the Hamilton principle; thus, the system is represented by various subsystems. The equation of motion of the shaft with a mass unbalance and a crack are established by adapting the local mass unbalance and the stiffness change. this is a reference system for the given system. Based on a model for transient behavior induced from vabrations measured at the bearings, an elementary Estimator is designed to detect mass unblance on the shaft. Using the Estimator, a bank of the Estimator is established to estimate the estimate the position of the mass unbalance and arranged at a certain location on the shaft. The informations for the given system are the measurements of bearing displacements and velocity.

• 제어로봇시스템학회논문지
• /
• 제15권1호
• /
• pp.1-7
• /
• 2009

As designing PID control on aircraft, we consider a gain scheduling on altitude and velocity. If pitot tube is not installed in the unpowered air vehicle, the control performance is reduced by the difference between ground speed and air speed with a wind considered. In this paper, a simple guidance controller (LOS: Line of Sight) and the wind estimator using Kalman filter are designed. And we minimize the wind effect through the estimator. Finally, we perform the 6-DOF nonlinear simulation with the wind model to verify the performance of the controller with the wind estimator.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.245-248
• /
• 1998

This paper proposes a sensorless velocity estimator using the reduced-order state equation of induction motor based on Kalman Filter. The electrical transients in the stator voltage equations of induction motor are neglected in the reduced-order model. The advantage of using the reduced-order model is to reduce the required number of numerical integrations for filtering the rotor speed. As changing the operating points and the parameters of the induction motor in simulation studies, the behavior of the sensorless velocity estimator as predicted by the reduced-order state equation of induction machine is compared with the behavior predicted by the complete state equation of induction machine.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.648-651
• /
• 1996

Samsung Electronics has developed high performance velocity and position controller for induction motors, and succeeded in mass production for the first time in Korea. Dynamic performance and final control accuracy of the controller are equivalent to those of AC servo motor controller. At present, we adopted the controller as spindle motor drive for Samsung CNC systems, and expect its wide use in industry as general purpose velocity and position controller for induction motor.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.11-14
• /
• 1996

Samsung Electronics has developed high performance velocity and position controller for induction motors and succeeded in mass production for first time in Lorea. Dynamic performance and final control accuracy of the controller are equivalent to those of AC servo motor controller. At present we adopted the controller as spindle motor drive for Samsung CNC systems and expect its wide use in industry as general purpose velocity and position controller for induction motor.