• Structural Engineering and Mechanics
• /
• v.40 no.5
• /
• pp.595-616
• /
• 2011

Impact experiments have been carried out on concrete slabs. The first group was traditionally manufactured, densely reinforced concrete targets, and the next were ordinary Portland and calcium aluminate cement based HPSFRC (High performance steel fiber reinforced concrete) and SIFCON (Slurry infiltrated concrete) targets. All specimens were hit by anti-armor tungsten projectiles at a muzzle velocity of over 4 Mach causing destructive perforation. In Part I of this article, production and experimental procedures are described. The first group of specimens were ordinary CEM I 42.5 R cement based targets including only dense reinforcement. In the second and third groups, specimens were produced using CEM I 42.5 R cement and Calcium Aluminate Cement (CAC40) with ordinary reinforcement and steel fibers 2 percent in volume. In the fourth group, SIFCON specimens including 12 percent of steel fibers without reinforcement were tested. A high-speed camera was used to capture impact and residual velocities of the projectile. Sample tests were performed to obtain mechanical properties of the materials. In the companion Part II of this study, numerical investigations and simulations performed will be presented. Few studies exist that examine high-velocity impact effects on CAC40 based HPSFRC targets, so this investigation gives an insight for comparison of their behavior with Portland cement based and SIFCON specimens.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2016-2021
• /
• 2003

This paper deals with a control technique of eliminating the transient vibration with respect to a waist axis of an articulated robot. This control technique is based on a model-based control in order to establish the damping effect on the driven mechanical part. The control model is composed of reduced-order electrical and mechanical parts related to the velocity control loop. The parameters of the control model can be obtained from design data or experimental data. This model estimates a load speed converted to the motor shaft. The difference between the estimated load speed and the motor speed is calculated dynamically, and it is added to the velocity command to suppress the transient vibration. This control method is applied to an articulated robot regarded as a time-invariant system. The effectiveness of the model-based control integrated into the position control loop is verified by simulations. Simulations show satisfactory control results to reduce the transient vibration at the end-effector.

• Journal of Biomedical Engineering Research
• /
• v.13 no.4
• /
• pp.331-338
• /
• 1992

In this study, Fuzzy control algorithm to generate a change of rocomotion condition according to an outer environment is introduced on a motorized wheelchair control. An optimal control rule for conquesting the less of safety and system Inefficiency in the past are given to this motorized wheelchair. And dynamic analysis Is also adopted to it. Using those rules, a proportional control was possible when the vehicle changed Its moving direction. The proposed method which considers the relationship between a moving velocity and the command from the joystick shows better performance in the change of moving direction.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.4
• /
• pp.524-528
• /
• 2006

A controller built with the gyro effect for a balance-beam can freely control the attitude of an unstructured object by changing the position of an inner gimbal. In this paper, we propose a new balance-beam controller that can detect the inertia of the load to limit the velocity of the load commanded by a user. We found that when there was smaller load inertia, a larger restoration displacement occurred. Therefore, the load can be identified by issuing a predefined command to measure the restoration displacement, which enables us to construct a controller that can limit the angular velocity of the load by planning the motion. Experimental results show the performance of the controller with different loads.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1998.10a
• /
• pp.159-165
• /
• 1998

In this paper the sway-control problem of a container crane is investigated. The control loop is divided into two stages. The first stage is a modified time optimal control for trolley traversing. The velocity command for trolley traversing consists of three components ; a reference velocity and two feedback signals for compensating the deviations of trolley and sway angle from their desired trajectories. For trolley's exact positioning the trolley dynamics is identified via an error equation identifier structure. The second stage is a nonlinear residual sway control that starts at the end of first stage. The control design for the second stage is investigated from the perspective of controling an underactuated system, and the control law combines the feedback linearization and variable structure control.

• Proceedings of the KOSOMBE Conference
• /
• v.1992 no.11
• /
• pp.71-76
• /
• 1992

In this study, Fuzzy control algorithm to generate a change of rocomotion cordition according to an outer environment is introduced on a motorized wheelchair control. An optimal control rules for conquesting the less of safety and system inefficiency in the past are given to this motorized wheelchair. And dynamic analysis is also adopted to it. Using those rules, a proportional control was possible when the vehicle changed its moving direction. The proposed method which considers the relationship between a moving velocity and the command from the joystick shows better performance in the change of moving direction.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.4
• /
• pp.350-358
• /
• 2009

This paper describes a result of the guidance and control for re-entry vehicle during TAEM phase. TAEM phase (Terminal Aerial Energy Management phase) has many conditions, such as density, velocity, and so on. Under these conditions, we have optimized trajectory and other states for guidance in TAEM phase. The optimized states consist of 7 variables, down-range, cross range, altitude, velocity, flight path angle, vehicle's azimuth and flight range. We obtained the optimized reference trajectory by DIDO tool, and used feedback linearization with neural network for control re-entry vehicle. By back propagation algorithm, vehicle dynamics is approximated to real one. New command can be decided using the approximated dynamics, delayed command input and plant output, NARMA-L2. The result by this control law shows a good performance of tracking onto the reference trajectory.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.3
• /
• pp.263-270
• /
• 2003

This paper deals with a control technique of eliminating the transient vibration of a waist axis of an articulated robot. This technique is based on a model-based control in order to establish the damping effect on the mechanical part. The control model is related to the velocity control loop, and it is composed of reduced-order electrical and mechanical parts. Using this model, the velocity of the load is estimated, which is converted to the motor shaft. The difference between the estimated load speed and the motor speed is calculated dynamically, and it is added to the velocity command to suppress the transient vibration of a waist axis of the robot arm. The function of this technique is to increase the cut-off frequency of the system and the damping ratio at the driven machine part. This control model is easily obtained from design or experimental data and its algorithm can be easily installed in a DSP. This control technique is applied to a waist axis of an articulated robot composed of a harmonic drive gear reducer and a robot arm with 5 degrees of freedom. Simulations and experiments show satisfactory control results to reduce the transient vibration at the end-effector.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.343-346
• /
• 2003

In order to discuss the availability of the hydrostatic guideway driven by the coreless linear motor to ultra precision machine tools, a prototype of guideway is designed and tested in this research. A coreless linear DC motor with the continuous force of 156 N and a laser scale with the resulution of 10 nm are used as the feeding system. The experiments are performed on the static stiffness. motion accuracy, positioning accuracy. microstep response and variation of velocity. The guideway has the infinite axial stiffness within 50 N of applied load, and has 0.08 ${\mu}{\textrm}{m}$ of linear motion error and 0.1 arcsec of angular motion error. It also has 0.21 ${\mu}{\textrm}{m}$ of positioning error and 0.09 ${\mu}{\textrm}{m}$ of repeatability, and it shows the stable response against the 10 nm resolution step command. The velocity variation of feeding system is less than 5%. From these results, it is confirmed that the hydrostatic guideway driven by the coreless linear motor is very useful for the ultra precision machine tools.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.2
• /
• pp.55-60
• /
• 2005

In order to develop the hydrostatic guideways driven by a core less linear motor for ultra precision machine tools, a prototype of guideway is designed and tested. A coreless linear DC motor with a continuous force of 156 N and a laser scale with a resolution of 0.01 ㎛ are used in the system. Experimental analysis on the static stiffness, motion errors, positioning error and its repeatability, micro step response and velocity variation of the guideway are performed. The guideway shows infinite stiffness within 50 N applied load in the feed direction, and by the motion error compensation method using the Active Controlled Capillary, 0.08 ㎛ linear motion error and 0.1 arcsec angular motion error are acquired. The guideway also reveals 0.21 ㎛ positioning error and 0.09 ㎛ repeatability, and it shows stable responses following a 0.01 ㎛ resolution step command. The velocity variation of feeding system is less than 0.6 ％. From these results, it is estimated that the hydrostatic guideway driven by a coreless linear motor is very useful for the ultra precision machine tools.