• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.4
• /
• pp.359-367
• /
• 2012

In this paper, the input split type series-parallel hybrid electric vehicle (SPHEV) is established and the interpretation of the dynamic characteristics in four kinds of HEV modes, such as electric vehicle mode, engine mode, hybrid mode, and regeneration mode, is described. For this research, the forward-facing approach simulation method is chosen, which is useful for vehicle dynamic analysis. The rating of each powertrain component is designed based on energy-based concept and electrical peaking hybrid (ELPH) method. Finally, the designed powertrain is evaluated with the developed PSiM simulator and simulation results are shown.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.367-373
• /
• 2017

In this paper, a new shift map was proposed to improve the fuel economy of a transmission mounted electric device(TMED) type dual clutch transmission(DCT) plug-in hybrid electric vehicle(PHEV) by considering transmission and motor losses. To construct the shift map, powertrain efficiencies of the engine-DCT-motor were obtained at each gear step. A shift map that provides the highest powertrain efficiency was constructed for the given wheel torque and vehicle speed. Simulation results showed that the fuel economy of the target PHEV can be improved by the new shift map compared with the existing engine optimal operating line(OOL) shift control.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.106-112
• /
• 2008

Modern vehicles require a high degree of refinement, including good drive ability to meet customer demands. Vehicle drive ability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. This paper focuses on the simulation of FTP-75 mode which is considered with spark timing control on transient condition. The acceleration is the most important factor for vehicle fuel economy. The retard of spark timing increases in proportion to acceleration. Likewise, bsfc(break specific fuel consumption) which is affected by spark timing also increases in proportion to acceleration. The result of simulation considered transient condition shows 0.3% of error comparing with a test on chassis-dynamometer.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.3
• /
• pp.240-248
• /
• 2017

This paper describes the development of a powertrain for a 20 kW experimental electric vehicle using a surface-mounted permanent magnet synchronous motor (SPMSM) and its application to a test vehicle. Two 10 kW SPMSMs are used in the powertrain, and two-level inverters are developed by using IGBTs to derive these motors. To control the SPMSM, a control board based on a TMS320F28335 DSP module, which has fast arithmetic function and floating point operator, is used. We develop a 100 V/40 A battery pack, which includes $32{\times}4$ LiFePO4 battery cells using commercial BMS. A commercial on-board charger with 220 V (AC) input and 100 V (DC) and 18 A output is used to charge the battery pack. The performance of the developed vehicle, such as acceleration availability, maximum speed, and maximum power, is estimated based on vehicle dynamics and verified through experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.135-143
• /
• 2014

Electrified vehicles can be classified with hybrid electric vehicles, battery electric vehicles and fuel cell electric vehicles. These vehicles have two more than energy converters which are the part of a powertrain. It is particularly difficult to estimate the power of hybrid electric vehicles due to two different energy converters with different power characteristics. Therefore, a new power concept for these vehicles is needed. The vehicle power as the new concept for solving this problem was defined in this study. The test method and the procedure were made a development in this study. Four electrified vehicles with different electric fraction were used to validate the method. Two percentage of COV was suggested as a criterion for the maximum vehicles power based on the previous studies. The repeatability of this method was within ${\pm}2$ per cent for the maximum vehicle power and within ${\pm}5$ per cent for the vehicle speed at maximum vehicle power.

• Journal of Power System Engineering
• /
• v.12 no.2
• /
• pp.23-28
• /
• 2008

The primary objective of this study is to truly understand reaction force be due to engine exciting force. Exciting forces of the engine apply a source of the vehicle NVH(Noise, Vibration, Harshness). To understand reaction force was applied MSC.Nastran software. Analyzed frequency response analysis of powertrain mount system. First, engine exciting force was applied field function. Also nonlinear characteristics was applied field function : such as dynamic spring constant and loss factor. And nonlinear characteristics was applied CBUSH. Generally characteristics of rubber mount is constant frequency. But characteristics of hydraulic mount depend to frequency. Therefore nonlinear characteristics was applied. Powertrain mounting system be influenced by powertrain specification, mount position, mount angle and mount characteristics etc. In this study, we was analyzed effects of powertrain mounting system. And we was varied dynamics spring constant and loss factor of mounts.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.305-310
• /
• 2007

This paper presents a damper system design in torque converter to minimize the vibration in powertrain of automatic transmission vehicle. The lock-up clutch in torque converter makes engine and transmission connected directly. When the lock-up clutch is engaged the torque fluctuation of engine is attenuated by the damper system. This function decides the vehicle power-train dynamic characteristics. At first, the dynamic hysteresis effect with any self and surface to surface contact problems of the damper springs in the damper system for torque converter is analyzed by using FEM. It is shown that these simulation results have a good design reference to energy dissipation operating by damper system in torque converter. And, to calculate dynamic characteristics, the vehicle model is structured by using $AMESim^{(R)}$?? that is a common use program. The vehicle model shows the frequency response of vehicle by changing the stiffness of damper spring, and these results lead the most suitable stiffness of spring. Also, new damper system is analyzed resonance frequency variation and is compared with prior damper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.16-22
• /
• 2007

Fuel efficiency is one of the major issues in regard to energy and environment. As customers desire more comfortable vehicles, increase of accessory traction force is necessary. Air conditioning system (ACS) consumes the biggest traction force among accessories, especially during summer. This means ACS is the primary object deteriorating fuel economy among accessories. Since direct measurement of traction force and fuel consumption in practical vehicle is difficult, comparison analysis is taken between vehicle with and without ACS working. For this comparison, real time measurements are carried out to know ACS traction force and fuel consumption. As a result of the comparison, a vehicle without ACS operation was 15.92% superior to a vehicle with ACS operating. It could be used as a fundamental material for improvement ACS for better fuel efficiency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.193-198
• /
• 2004

In order to keep the market competitiveness, it is desirable for automotive manufacturer to meet the customer's various aspects of requirements. The overall NVH (Noise, Vibration, and Harshness) performance has been an important measure when evaluating overall vehicle performance, product quality, and enhancing customers' loyalty to the product. The noise and vibration, while the engine is idling, has been brought particular attention to the drivers and passengers, because they encounter the operation conditions quite frequently without other masking noise sources: wind noise, road noise, and even powertrain radiated noise at higher speed driving. The specific noise, defined as 'CHIT' noise, has been identified as a potential customer issue, from the Pickup Truck with newly developed V8 powertrain. This paper describes the definition of the noise, identifying the potential sources, and noise radiation mechanisms, based on series of powertrain and vehicle test and verification processes. Then, based on the root-cause identified, the design change has been proposed and validated with several vehicles in order to have a complete satisfaction of the customer.