• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.125-135
• /
• 2004

The validity of simulation has been well-established for decades in areas such as computer and communication system. Recently, the technique has become entrenched in specific areas such as transportation and traffic forecasting. Several methods have been proposed for investigating complex traffic flows. However, the dynamics of vehicles and their driver's characteristics, even though it is known that they are important factors for any traffic flow analysis, have never been considered sufficiently. In this paper, the traffic simulation using a multi-agent approach with considering vehicle dynamics is proposed. The multi-agent system is constructed with the traffic environment and the agents of vehicle and driver. The traffic environment consists of multi-lane roads, nodes, virtual lanes, and signals. To ensure the fast calculation, the agents are performed on the based of the rules to regulate their behaviors. The communication frameworks are proposed for the agents to share the information of vehicles' velocity and position. The model of a driver agent which controls a vehicle agent is described in the companion paper. The vehicle model contains the nonlinear subcomponents of engine, torque converter, automatic transmission, and wheels. The simulation has proceeded for an interrupted and uninterrupted flow model. The result has shown that the driver agent performs human-like behavior ranging from slow and careful to fast and aggressive driving behavior, and that the change of the traffic state is closely related with the distance and the signal delay between intersections. The system developed shows the effectiveness and the practical usefulness of the traffic simulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.157-164
• /
• 2000

It is known that residual aligning torque of tires causes vehicle pull. There is, however, only a little literature available which shows how the residual aligning torque of tires causes vehicle pull. In this paper, a vehicle model in two degrees of freedom was adopted for the analysis of a vehicle under the straight-ahead motion. The analysis with this vehicle model clearly shows the effect of residual aligning torque of tires on vehicle pull. In order to show the validity of the analysis, a vehicle commercially available was selected. This vehicle was modeled in 137 degrees of freedom system with multibody dynamics software. Vehicle pull simulation results show that vehicle model drifts in lateral direction due to the residual aligning torque of tires. Vehicle test results with the car were also included.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.91-99
• /
• 2003

When the driver suddenly depresses the brake pedal under critical conditions, the desired trajectory of the vehicle can be changed. In this study, the vehicle dynamics and fuzzy logic controller are used to control the vehicle trajectory. The dynamic vehicle model consists of the engine, the rotational wheel, chassis, tires and brakes. The engine model is derived from the engine experimental data. The engine torque makes the wheel rotate and generates the angular velocity and acceleration of the wheel. The dynamic equation of the vehicle model is derived from the top-view vehicle model using Newton's second law. The Pacejka tire model formulated from the experimental data is used. The fuzzy logic controller is developed to compensate for the trajectory error of the vehicle. This fuzzy logic controller individually acts on the front right, front left, rear right and rear left brakes and regulates each brake torque. The fuzzy logic controlling each brake works to compensate for the trajectory error on the split - $\mu$ road conditions follows the desired trajectory.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.143-150
• /
• 2006

In this paper, a new bushing model for vehicle dynamics analysis using Bouc-Wen hysteretic model is proposed. Bushing components of a vehicle suspension system are tested to capture the nonlinear behavior of rubber bushing elements using the MTS 3-axes rubber test machine. The results of the tests are used to define parameters in Bouc-Wen bushing model, which was employed to represent the hysteretic characteristics of the bushing. Bushing parameters are obtained by using genetic algorithms and sensitivity analysis of parameters are also carried out. ADAMS program was used for the identification process and VisualDOC program was employed to find the optimal parameters. A half-car simulation was carried out to show the usefulness of the developed bushing model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.59-67
• /
• 2014

A numerical model and a controller of Active Front wheel Steer (AFS) system are designed in this study. The AFS model consists of four sub models, and the AFS controller uses sliding mode control and PID control methods. To test this model and controller an Integrated Dynamics Control with Steering (IDCS) system is also designed. The IDCS system integrates an AFS system and an ARS (Active Rear wheel Steering) system. The AFS controller and IDCS controller are compared under several driving and road conditions. An 8 degree of freedom vehicle model is also employed to test the controllers. The results show that the model of AFS system shows good kinematic steering assistance function. Steering ratio varies depends on vehicle velocity between 12 and 24. Kinematic stabilization function also shows good performance because yaw rate of AFS vehicle tracks the reference yaw rate. IDCS shows improved responses compared to AFS because body side slip angle is also reduced. This result also proves that AFS system shows satisfactory result when it is integrated with another chassis system. On a split-m road, two controllers forced the vehicle to proceed straight ahead.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.684-689
• /
• 2000

In this paper, the equations of motion about vehicle, powertrain and brake system were derived. The vehicle has eight degrees of freedom with nonlinear tire model and the powertrain has two degrees of freedom containing engine, torque converter and four speed automatic transmission. The brake system has two states about front and rear brake line pressures. The transient tire model with first order time lag is also subjoined for low speed or stop-and-go simulation. The modeling was derived considering two points - the fidelity and the simplicity. The simulation using this model is similar with real vehicle dynamic behavior and the model is made as simple as possible far fast simulation. It is validated that the derived vehicle model can be applicable to the real time simulation.

• Structural Engineering and Mechanics
• /
• v.57 no.1
• /
• pp.21-43
• /
• 2016

A conditional probability based approach known as Particle Filter Method (PFM) is a powerful tool for system parameter identification. In this paper, PFM has been applied to identify the vehicle parameters based on response statistics of the bridge. The flexibility of vehicle model has been considered in the formulation of bridge-vehicle interaction dynamics. The random unevenness of bridge has been idealized as non homogeneous random process in space. The simulated response has been contaminated with artificial noise to reflect the field condition. The performance of the identification system has been examined for various measurement location, vehicle velocity, bridge surface roughness factor, noise level and assumption of prior probability density. Identified vehicle parameters are found reasonably accurate and reconstructed interactive force time history with identified parameters closely matches with the simulated results. The study also reveals that crude assumption of prior probability density function does not end up with an incorrect estimate of parameters except requiring longer time for the iterative process to converge.

• International Journal of Automotive Technology
• /
• v.7 no.7
• /
• pp.777-784
• /
• 2006

The lateral dynamic behaviours of a track inspection vehicle with laterally guided system are studied for the safety and comfort. A 10-DOF dynamic model is proposed counting for lateral and yaw motions. The equations for motions of the vehicle running on curved tracks at a constant speed are presented. It is shown by simulation that lateral guiding forces applied to the guiding wheels on the inner side of the track increase in a larger scale in comparison with those on the outer side when the vehicle passes through curved tracks with cant, and the front guiding spring forces is larger than the rears. Lateral vibrations due to yaw motions of the vehicle take place when the vehicle runs through curved tracks. Finally, effect of the lateral guidance on the vehicle dynamics is also examined and advantages of such a guiding system are discussed in some details. An optimal guided control is applied to restrain the lateral and yaw motions. The comparisons between the active and passive guidance explain the effect of the active control approaches.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.334-337
• /
• 1996

This is a paper intended for initial stage of vehicle modeling and design. The needs to determine a variety of vehicle suspension parameters required for initial design has been difficult and time-consuming task. In order to facilitate a concise and efficient presentation of initial vehicle design procedure, this paper uses a mathematical model and physical geometry. Vehicle model consists of dimensions, inertias and mechanical constants. These vehicle model parameters divided into several categories : basic parameters, coefficients and constants, design specification, spring and damper, bush stiffness, stabilizer bar, suspension geometry, tire, and vehicle weights of various design condition. This paper uses a vehicle design fundamental (VDF) program running under Windows 95 graphical interface. The features of VDF will be briefly outlined in this paper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.2
• /
• pp.170-176
• /
• 2008

Anti roll bar model for real time multibody vehicle dynamics model has been proposed using kinematic constraint. Anti roll bar have been modeled by kinematic relationship, and mass properties are neglected. Relative angle of torsion bar spring is computed by constraint about drop-link using Newton-Raphson iteration, and then the torque of torsion bar spring can be computed with the angle and torsion spring stiffness. Finally anti roll bar force acting on both knuckle can be calculated. To validate the proposed method, half car simulations of McPherson strut suspension and full car simulations are also carried out comparing with the ADAMS vehicle model with anti roll bar. CPU times are also measured to see the real-time capabilities of the proposed method.