• 한국전기전자재료학회논문지
• /
• 제25권11호
• /
• pp.930-937
• /
• 2012

Newly developed Series hybrid low-floor articulated vehicle which can meet both road and railway running conditions. It has the rated driving speed of 80 km/h and three driving modes with hybrid(engine+battery) driving mode, engine driving mode, battery driving mode. The battery driving mode requires the several 10 km running without additional charging operation. The vehicle has been equipped with LPB (lithium polymer battery) pack for the series hybrid propulsion system. LPB pack consists of 168 cells (3.7 V in a cell, 80 Ah) in series, DC Circuit breaker, mechanical rack, BMS (battery management system). This paper has shown the design process of LPB pack and application to the vehicle. Driving results in the road was successful to be satisfied with the requirement of the series hybrid vehicle.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.866-867
• /
• 2011

As part of the green growth, The Green Car has attracted wide attention. Types of the Green Car are Electric Vehicle, Plug-in Hybrid Electric Vehicle, Hybrid Electric Vehicle, Fuel Cell Vehicle and Clean Diesel Vehicle. Of these, The electric vehicle is equipped with the BDU(Battery Disconnecting Unit). BDU is supplying stable battery power and blocking it to protect electrical system of the electric vehicle. The BDU consists of electric components such as current sensor, fuse and pre-charge resistor. These must pass Voltage withstand test, Salt mist test, Thermal shock test, Vibration test and Short-circuit test commonly to verify reliability of the electric components. In addition, The current sensor should be verified whether normal operation. The breaking capacity of fuse should be verified. The durability of pre-charge resistor should be verified by supplying battery power and blocking it repeatedly. The reliability of BDU as well as the electric vehicle is secured by verifying the reliability of electric components. In addition, It will contribute to the acceleration and promotion of Green Car Technology.

• 자동차안전학회지
• /
• 제10권3호
• /
• pp.38-44
• /
• 2018

Conventional brake system was used for passenger cars and SUV for a long time. However, the high performance brake system has strongly required because of increase of engine power and customer's favorites etc. In this paper, a new high performance brake system for Europe was proposed. For this system, the high performance caliper and disc were newly developed. The superiorities of the developed high performance brake system were verified via heat capacity, hydraulic stiffness, corrosion and harsh braking mode test. Also, the high performance caliper and disc for the light-weight were applied to AL-Alloy and can obtain the weight reduction effect of 2.9 kg per vehicle. Finally, a developed high performance brake system is expected to be used for realization of the high performance at the same platforms.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.124-132
• /
• 2007

The main objective of this work is to investigate the characteristics of a heat pump system for fuel cell electric vehicle (FCEV). The present heat pump system adopts an electrically driven compressor running with R134a and uses the heat from the fuel cell stack as the heat source for the exterior heat exchanger. The experimental work has been done with various operating conditions such as different compressor speeds, fuel cell stack coolant temperatures and flow rates. The heating capacity was measured to be from 4 to 10 kW at $-20^{\circ}C$ ambient temperature, and the outlet temperature of interior heat exchanger was up to $70^{\circ}C$. After 30 seconds from start-up, the system reached a steady state and the heating capacity of 6.8 kW was acquired, and after 90 seconds, the air outlet temperature of interior heat exchanger became $35^{\circ}C$.

• Structural Engineering and Mechanics
• /
• 제60권2호
• /
• pp.237-249
• /
• 2016

There are constraints on truck weight, axle configurations and size imposed by departments of transportation around the globe due to structural capacity limitations of highway pavements and bridges. In spite of that, freight movers demand some vehicles that surpass the maximum size and legal weight limits to use the transportation network. Oversized trucks serve the purpose of spreading the load on the bridge; thus, reducing the load effect on the superstructure. For such vehicles, often a quick structural analysis of the existing bridges along the traveled route is needed to ensure that the structural capacity is not exceeded. For a wide vehicle having wheel gage larger than the standard 1830 mm, the girder distribution factors in the design specifications cannot be directly used to estimate the live load in the supporting girders. In this study, a simple approach that is based on finite element analysis is developed by modifying the AASHTO LRFD's girder distribution factors for slab-on-steel-girder bridges to overcome this problem. The proposed factors allow for determining the oversized vehicle bending moment and shear force effect in the individual girders as a function of the gage width characteristics. Findings of the study showed that the relationship between the girder distribution factor and gage width is more nonlinear in shear than in flexure. The proposed factors yield reasonable results compared with the finite element analysis with adequate level of conservatism.

• 한국항해항만학회지
• /
• 제31권1호
• /
• pp.107-113
• /
• 2007

교통의 흐름에 있어서의 트럭 및 콘테이너 차량 등 대형차량의 혼입은 차체의 크기에 기인한 넓은 공간의 점유 및 승용차에 비해 상대적으로 떨어지는 차량운행 능력 등의 특성 때문에 도로의 용량을 감소시키는 중요한 요인이 된다. 도로의 교통용량산정 시 이러한 대형차량의 혼입에 의한 용량의 감소를 나타내는 척도로서의 승용차 환산계수의 개념은 1965년 도로용량편람에서 처음으로 도입되었으며, 이후 구미의 많은 학자들에 의해 연구되었다. 본 연구에서는 차량배열 형태에 따른 차두시간의 분석을 통해 환산계수의 도출을 시도하였다. 분석을 위한 교통자료의 수집은 통행차량 차종의 대부분이 승용차와 대형차로 구성되어 있으며 비교적 관측이 용이한 부산시 도시고속도로의 평지구간에서 첨두시간과 비 첨두시간으로 나누어 실시되었다. 본 연구에서의 환산계수 산정방법은 차두시간의 분석을 통한 미시적 접근방법인바, 동방법의 정확성 및 효율적 검증을 위해서는 거시적 접근 방법에 의한 산정방법과의 비교분석이 요구된다.

• 대한교통학회지
• /
• 제7권2호
• /
• pp.89-111
• /
• 1989

This study concentrates on a basic investigation research related to some of parameters to be used for the analysis of capacity and the level of service for signalized intersections. The parameters to be studied are ideal saturation flow rate, large vehicle's passenger car equivalent(PCE) ane the lane utilization factors of through and left turn vehicles. The field data were collected at six intersections in Seoul using video cameras so as to reflect conditions in urban areas. In this study discharge headway based on a rear bumper of each vehicle was used and all the parameters were estimated using a regression technique. The findings of this research are as follows : 1. The saturation headway and saturation flow rate on a single lane with the lane width of 3.1m are 1.652 seconds and 2,180 pcphgpl. It was found that the frist 5 vehicles in the queue experience some start-up lost time. 2. It was confirmed that the new method adopted for the estimate of large vehicle's PCE gives larger PCE values than those derived from the method commonly used. 3. For the estimate of lane utilization factors of through and left turn vehicles, a relationship was established and the corresponding formulas were developed.

• 자동차안전학회지
• /
• 제14권3호
• /
• pp.41-47
• /
• 2022

Composite material is recently very important material for eco-friendly vehicles because of its excellent mechanical property and lightweight effect. So, many research results have been recently published for developing the composite material to apply vehicles. In this paper, new brake system is presented using composite material to response this situation. And advantages in terms of performance compared to competitive company will be discussed in depth to verify superiorities of the new composite brake. To do so, composite brake systems which have the same size as the competitive company to the same vehicle is applied. And superiorities through a variety of test results are presented. First, normal braking performances are compared with competitive company through braking effect, heat capacity and friction test, Second, circuit driving and high speed fade test are also verified with competitive company to confirm harsh braking performances for the new composite brake system. Finally, the effects of applying the composite brake to automobile industry like electric car are analyzed.

• 한국인공지능학회지
• /
• 제11권4호
• /
• pp.21-27
• /
• 2023

This paper discusses a deep learning-based road surface analysis system that collects data by installing vibration sensors on the 4-axis wheel bearings of a vehicle, analyzes the data, and appropriately classifies the characteristics of the current driving road surface for use in the vehicle's control system. The data used for road surface analysis is real-time large-capacity data, with 48K samples per second, and the A2B protocol, which is used for large-capacity real-time data communication in modern vehicles, was used to collect the data. CAN and CAN-FD commonly used in vehicle communication, are unable to perform real-time road surface analysis due to bandwidth limitations. By using A2B communication, data was collected at a maximum bandwidth for real-time analysis, requiring a minimum of 24K samples/sec for evaluation. Based on the data collected for real-time analysis, performance was assessed using deep learning models such as LSTM, GRU, and RNN. The results showed similar road surface classification performance across all models. It was also observed that the quality of data used during the training process had an impact on the performance of each model.

• International journal of advanced smart convergence
• /
• 제11권3호
• /
• pp.222-228
• /
• 2022

As a means to cope with the climate change crisis caused by global warming, automobile manufacturers continue to make efforts to use the driving energy of vehicles as electricity. As a result, parts industry such as battery, motor, and controller are attracting attention. China is often seen in large cities, with electric vehicles such as electric bicycles, electric motorcycles, and small electric vehicles popularized and commercialized, mainly in large cities. However, small electric vehicles are not popular in Korea, which is why the country's topography is high in hills. In order to drive the hilly domestic roads, power performance including vehicle climbing ability should be improved. In order to improve the power performance and the climbing capacity of small electric vehicles, the capacity of the motor should be increased. However, when the performance of the motor is improved, the weight of the motor becomes heavy and the price competitiveness is likely to decrease. In addition, in order to operate a high-performance motor, the power consumption of the battery is rapidly increased, so various problems must be solved. In order to commercialize a small electric vehicle for one or two people who do not emit harmful exhaust gas to the human body in a hilly domestic terrain, it is effective to have a separate transmission system. In this study, we were conducted dynamometer test to produce a continuously variable transmission(CVT) system prototype using a spring that can be applied to a small electric vehicle and to install a CVT system prototype manufactured in a small electric vehicle. The dynamometer test results showed that the maximum speed performance, acceleration performance, and climbing performance were improved.