• Journal of Environmental Science International
• /
• v.19 no.6
• /
• pp.665-670
• /
• 2010

Pollutants from urban pavement consists various kinds of substances which are originated from dry deposition, a grind out tire, corrosive action of rain to pavement and facilities and raw materials of the road etc.. These are major pollutants of urban NPS (Non-point source) during rainfall period. However there is not enough information to control such pollutants for appropriate management of natural water quality. In this study of transportation areas, three monitoring stations were set up at trunk road, urban highway and national road in Gyeongnam province. Runoff flow rate was measured at every 15minutes by automatic flow meters installed at the end of storm sewer pipe within the road catchment area for water quality analysis. Data was collected every 15 minutes for initial two hours of rainfall. Additional samples were collected 1-4 hours interval till the end of rainfall. The monitoring parameters were $COD_{Mn}$, SS, T-N & T-P and heavy metals. The average EMCs of TSS and $COD_{Mn}$ were 62.0 mg/L and 24.2 mg/L on the city trunk road, which were higher than those of urban highway and national road, indicating higher pollutant loads due to activities in the city downtown area beside the vehicle. On the other hand, the average EMC of T-N and T-P were in the range of 2.67-3.23 mg/L and 0.19-3.21 mg/L for all the sampling sites. Heavy metals from the roads were mainly Fe, Zn, Cu and Mn, showing variable EMCs by the type of road. From the TSS wash-off analysis in terms of FF(first flush) index, first flush phenomenon was clearly observed in the trunk road(FF : 0.89-1.43). However, such mass delivery behavior was not apparently shown in urban highway(FF : 0.90-1.11) and national road(FF : 0.81-1.41).

• International Journal of Oral Biology
• /
• v.43 no.3
• /
• pp.147-153
• /
• 2018

The aim of the present study was to evaluate the central antinociceptive effects of eugenol after intraperitoneal administration. Experiments were carried out using male Sprague-Dawley rats. Subcutaneous injection of 5% formalin-induced nociceptive behavioral responses was used as the pain model. Subcutaneous injection of 5% formalin significantly produced nociceptive responses by increasing the licking time during nociceptive behavior. Subsequent intraperitoneal injection of 100 mg/kg of eugenol led to a significant decrease in the licking time. However, low dose of eugenol (50 mg/kg) did not affect the nociceptive behavioral responses produced by subcutaneous injection of formalin. Intrathecal injection of $30{\mu}g$ of naloxone, an opioid receptor antagonist, significantly blocked antinociceptive effects produced by intraperitoneal injection of eugenol. Neither intrathecal injection of methysergide ($30{\mu}g$), a serotonin receptor antagonist nor phentolamine ($30{\mu}g$), an ${\alpha}-adrenergic$ receptor antagonist influenced antinociceptive effects of eugenol, as compared to the vehicle treatment. These results suggest that central opioid pathway participates in mediating the antinociceptive effects of eugenol.

• Journal of Hydrogen and New Energy
• /
• v.27 no.6
• /
• pp.712-720
• /
• 2016

When bioethanol and water are mixed at a proper ratio, phase separation can occur because of the immiscibility of biobutanol with water. Phase separation in bioethanol blends fuels is a major problem for gasoline vehicle users due to effect of octane number and component corrosion. Thus, in this study, the phase separation of bioethanol was examined effect of bioethanol blends (E3 (3 vo.% bioethanol in gasoline), E5 and E10) in presence of water. The effect were evaluated behavior with phase separation test, simulation test of fuel tank in gas station according to water addition volume and it was investigated change of water content, bioethanol content and octane number for gasoline phase in bioethanol blends (E3, E5 and E10) every 1 week after water addition. The E3 occurred phase separation more easily than the E5 and E10 in small water contents because solubility of water on ethanol content difference in gasoline-ethanol. It was kept a initial level of water content, bioethanol content, and octane number by repeated sample replacing in simulation test of fuel tank.

• Journal of the Ergonomics Society of Korea
• /
• v.28 no.3
• /
• pp.63-71
• /
• 2009

A car navigation system as an in-vehicle route guidance information (RGI) offers a state-of-the-art technological solution to driver navigation in an unfamiliar area. However, the RGI is provided by some pre-determined options in terms of the interface between a driver and a car navigation system. Drivers occasionally pass the target intersection owing to non- or late- recognizing it. This paper is examined the position of driver's turn signal operation and intersection recognition approaching at the target intersection which is difficult to identify, as a fundamental research on developing the additional RGI connecting with the turn signal control. The field experiment was conducted to measure distances of the turn signal operation and the intersection recognition from the target intersection according to left turns, right turns, and landmarks at adjacent intersection. And glance behavior to the car navigation display was evaluated by using an eye camera. The results of the field study indicate that, most case of driving, drivers operate the turn signal until 40m to 50m before coming to the target intersection. The driving simulator experiment was performed to examine the effectiveness of providing the additional RGI when drivers did not operate the turn signal approaching at the target intersection based on the results of the field study. To provide the additional RGI is effective for the intersection identification and recognition, and expected to improve the traffic safety and the comfort for drivers.

• Biomedical Science Letters
• /
• v.24 no.3
• /
• pp.239-244
• /
• 2018

Recently, many researches regarding the natural products which alternate with chemical products have been done. Among them, boswellia is well known for effect on anti-oxidative effect and inflammation. The aim was the effect boswellia of formalin- induced orofacial and temporomandibular joint (TMJ) pain on experimental animals was investigated. Experiments were carried out using subcutaneous (SC) pain model and TMJ pain model that were induced by the injection of 5% formalin into the right vibrissa pad (SC, $50{\mu}L$) or TMJ ($30{\mu}L$) of rats, respectively. In both models, formalin (5%), formalin after distilled water (vehicle), formalin after boswellia extract (p.o., concentrations of 15, 30 mg/kg) (n=6). The number of scratching on the injected region was scored during the 9 successive periods of 5 min intervals following injection of formalin. Oral administration of boswellia (15, 30 mg / kg) reduced formalin-induced SC orofacial pain behavioral responses. SC orofacial pain behavioral responses was significantly reduced at 20~35 min. In the experimental group injected into temporomandibular joints, the pain response was significantly reduced by $276.2{\pm}8.20$ and $78.3{\pm}4.7$ after oral administration of boswellia (15, 30 mg / kg) at $398.3{\pm}24.8$ times. As a result of the passage of time, the oral administration of boswellia showed a significant effect of reducing the temporomandibular joint pain 30 minutes after the injection of formalin. This study confirmed that oral administration of boswellia modulated the pain behavior in both models. In conclusion, boswellia extract may be a potential therapeutic treatment for orofacial pain.

• Structural Engineering and Mechanics
• /
• v.52 no.5
• /
• pp.1019-1032
• /
• 2014

Rails are key elements in railway superstructure since these elements receive directly the train load transmitted by the wheels. Simultaneously, rails must provide effective stress transference to the rest of the track elements. This track element often deteriorates as a consequence of the vehicle passing or manufacturing imperfections that cause in rail several defects. Among these rail defects, transverse cracks highlights and are considered a severe pathology because they can suddenly trigger the rail failure. This study is focused on UIC-60 rails with transverse cracks. A 3-D FEM model is developed in ANSYS for the flawless rail in which conditions simulating the crack presence are implemented. To account for the inertia loss of the rail as a consequence of the cracking, a reduction of the bending stiffness of the rail is considered. The numerical models have been calibrated using the first four bending vibration modes in terms of frequencies. These vibration frequencies have been obtained using the Experimental Modal Analysis technique, studying the changes in the modal parameters of the rails induced by the crack and comparing the results obtained by the model with experimental results. Finally, the calibrated and validated models for the single rail have been implemented in a complete railway ballasted track FEM model in order to study the static influence of the cracks on the rail deflection caused by a load passing.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.501-506
• /
• 2001

Computer modeling is essential to evaluate possible design of suspension for a railway vehicles. By creating a simulation, the engineers are able to assess the feasibility of a given design and change the design factors to get a better design. But if one wishes to perform complex analysis on the simulation, such as railway vehicle dynamic, the computational time can become overwhelming. Therefore, many researchers have turned to surrogate modeling. A surrogate model is essentially a regression performed on a data sampling of the simulation. In the most general sense, metamodels(surrogate model) take the form $y(x)=f(x)+{\varepsilon}$, where y(x) is the true simulation output, f(x) is the metamodel output, and $\varepsilon$ is the error between the two. In this paper, a second order polynomial equation is partially used as a metamodel to represent the forty-six dynamic performances for high speed train. The number of factors as design variables of the metamodel is twenty-nine, which are composed the dynamic characteristics of suspension. This metamodel is used to search the optimum values of suspension characteristics which minimize the dynamic responses for high speed train. This optimization is a multi-objective problem which have many design variables. This paper shows that the response surface model which is made through the design of analysis of computer experiments method is very efficient to solve this complex optimization problem.

• Journal of Digital Convergence
• /
• v.16 no.7
• /
• pp.249-257
• /
• 2018

The purpose of this study is to construct a virtual reality simulation environment for searching and evaluating evaluation criteria for road safety facilities with new technologies. Virtual reality simulation requires high realism and accurate behavior data extraction. To do this, we used the Unreal Engine to create the environment by dividing it into an external environment and a vehicle environment. After that, a sample simulation for the luminescent road markers and preliminary experiments were conducted. As a result, luminescent road markers showed better 5m interval than 10m interval. It can be confirmed that it can be used in the simulation for searching the evaluation criteria for the new road safety facilities that incorporate the new technology in the future. In the future, it will be possible to simulate various environments by adding modeling and sample components for other road facilities.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.848-853
• /
• 2004

Regarding to the project SUAV (Smart Unmanned Aerial Vehicle) in KARI (Korea Aerospace Research Institute), several engine configurations has been evaluated. However it's not an easy task to collect all the necessary data of each engine for the analysis. Usually, some kind of modeling technique is required in order to determine the unknown data. In the present paper a qualitative method for reverse engineering is proposed, in order to identify some design patterns and relationships between parameters. The method can be used to estimate several parameters that usually are not provided by the manufacturer. The method consists of modeling an existing engine and through a simulation, compare its transient behavior with its operating envelope. In the simulation several parameters such as thermodynamics, performance, safety and mechanics concerning to the definition of operation-envelope, have been discussed qualitatively. With the model, all engine parameters can be estimated with acceptable accuracy, making possible the study of dependencies among different parameters such as power-turbine total inertia, TIT, take-off time and part load, in order to check if the engine transient performance is within the design criteria. For more realistic approach and more detailed design requirements, it will be necessary to enhance the compressor map first, and more realistic estimated values must be taken into account for intake-loss, bleed-air and auxiliary power extraction. The relative importance of these “unknown” parameters must be evaluated using sensitivity analysis in the future evaluation. Moreover, fluid dynamics, thermal analysis and stress analysis necessary for the resulting life assessment of en engine, will not be addressed here but in a future paper. With the methodology presented in the paper was possible to infer the relationships between operation-envelope and engine parameters.

• Journal of the Korea Society for Simulation
• /
• v.20 no.3
• /
• pp.89-100
• /
• 2011

The MAGLEV (Magnetically Levitated Vehicle) system, which is under commercialization as a new transportation system in Korea, is operated by means of unmanned automatic control system. Therefore the plan of train operation should be carefully established and validated in advance. In general, when making the train operation plan, the statistically predicted traffic data is used. However, traffic wave can occur when real train service is operated, and the demand-driven simulation technology is required to review train operation plans and service qualities considering traffic wave. This paper presents a method and model to simulate the MAGLEV's operation considering continuous demand changes. For this purpose, we employed the discrete event model which is suitable for modeling the behavior of railway passenger transportation, and modeled the system hierarchically using DEVS (Discrete Event System Specification) formalism. In addition, through the implementation and experiment using DEVSim++ simulation environment, we tested the feasibility of the proposed model and it is also verified that our demand-driven simulation technology could be used for the prior review of the train operation plans and strategies.