• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.848-850
• /
• 2000

본 논문에서는 신경회로망을 이용하여 On-Line상에서 EEG(Electroencephalogram) 신호를 분류하는 방법을 제안한다. EEG 신호란 인간의 두뇌활동에서 발생하는 전기적 신호로서 고도의 비선형과 시변 특성을 지니고 있어 정량적인 분석이 어려운 신호로 여겨진다. 이를 분석하기 위해 본 논문에서는 입력 벡터들을 서브클래스로 분류하는 경쟁 레이어와 서브클래스를 모아 정해진 클래스를 선택하는 선형 레이어로 이루어진 LVQ (Learning Vector Quantization) 신경망을 구성하고 On-Line 분석결과를 제시한다. 이러한 On-line 분석방법은 EEG 신호를 실시간으로 분석하여 컴퓨터를 인간의 생각만으로 제어될 수 있는 BCI(Brain Computer Interface)의 구현에 사용될 것이다.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.87-89
• /
• 2005

If the three phases are not balanced, the current in neutral line is not zero. Then, the induced voltage can be generated In communication line. The KEPCO's rule about unbalanced current in single electric pole is a twenty percent of phase current. But the unbalanced current in double electric pole can't decide the rule because there are many different views. This paper develops the calculation and analysis technique of neutral current in single electric pole and double electric pole using equivalent circuit analysis, vector analysis and EMTP simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.527-530
• /
• 1996

The Kalman filter has been used as a self-localization method for the mobile robot. To satisfy the assumptions inherent in the Kalman filter, we should calibrate the sensors of the robot before use of them. However, it is generally hard to find exact sensor parameters, and the parameters may change during the robot task as the environment varies. Thus we need to perform on-line sensor calibration, by which we can obtain more credible location of the mobile robot. In this paper, we present an on-line sensor calibration scheme which estimates the unknown sensor bias and the current position of the robot. To this end, first we find out the calibration errors of the sensor from redundant sensory data using the parity vector and recursive minimum variance estimation. Then we calculate the current position of the robot by weighted least square estimation without internal encoder data. The performance of the proposed method is evaluated through computer simulation.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1282-1286
• /
• 1999

This paper presents the DQ transfomation and space vector modulation method to develop a control algorithm of distribution STATCON(STATic CONdenser) for line voltage regulation, dc link voltage regulation and harmonics compensation. The Performance analysis of a PI with ramp comparision and synchronous reference frame current controller is carried out. Based on these analysis, the control performances are desirable to compensate the harmonics and to regulate de link and line voltage of Distribution line.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.433-442
• /
• 1995

For the line search of a multi-variable optimization, an efficient algorithm is presented. The algorithm sequentially employs several polynomial approximations such as 2-point quadratic interpolation, 3-point cubic interpolation/extrapolation and 4-point cubic interpolation/extrapolation. The order of polynomial function is automatically increased for improving the accuracy of approximation. The method of approximation (interpolation or extrapolation) is automatically switched by checking the slope information of the sample points. Also, for selecting the initial step length along the descent vector, a new approach is presented. The performance of the proposed method is examined by solving typical test problems such as mathematical problems, mechanical design problems and dynamic response problems.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1368-1369
• /
• 2008

This paper describes the electric field distribution analysis along a shield form inner vacuum interrupter(VI). The equipotential line and electric field and field vector in a VI are analysed by a finite element method at various shield form. in result, The equipotential line and electric field distribution was affected to VI shield gap. The reason is as it gets distortion of equipotential line done. finally, this paper recognized whether or not affected, and proposed gap with the most suitable shield length and an external insulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.788-795
• /
• 2000

In this paper, a method for the precise impedance measurement of coaxial loads using an offset open and short as the reflection standards and reference air lines with different lengths as the impedance standards is proposed. Measured input impedances of power sensors and thermistor mounts obtained from SWR bridges(5~400MHz) and a vector network analyzer(100~1,000MHz) are presented in the frequency range of 5MHz to 1,000 MHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.478-479
• /
• 2008

this paper describes the electric field distribution interpretation along a shield form inner vacuum interrupter(VI). The equipotential line and electric field and field vector in a VI are analysed by a finite element method at various shield form. in result, The equipotential line and electric field distribution was affected to VI shield form. The reason is as it gets distortion of equipotential line done. shield of cup type is how to electric field distribution, finally, this paper recognized whether or not affected, and proposed gap with the most suitable shield length and an external insulation.

• Journal of Power Electronics
• /
• v.3 no.1
• /
• pp.24-32
• /
• 2003

The commutation and control in matrix converters is more complicated as in voltage source converters. Natural freewheeling paths do not exist and the theoretic absent storage elements result in a direct coupled system of load and line currents as well as voltages. The paper offers an overview about staggered commutation and control policies in matrix converters. Based on the knowledge about load current direction and the signs of the line to line input voltages different multi-step commutation policies were derived. This paper examines the application of that policies in the case of space vector modulation and direct control methods with the focus on the resulting effects to the reference output voltage deviation.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.106-107
• /
• 2019

This paper propose a new 3D SVM method for three-phase four wire inverter for fault isolation at a single line ground fault. The available switching combination for isolation of a single line ground fault was analyzed. Using this method, voltage vector diagrams according to each switching combination were classified according to various ground fault situations, and 3D SVM method was performed by generating command for fault isolation. The proposed methods are mathematically analyzed and verified by PSIM simulation.