• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.553-571
• /
• 2019

Geometric variation including welding distortion accumulates as many parts are joined together, ultimately affecting the final product. This variation is then subjected to correction, which requires considerable effort, time, and cost. This variation can be categorized as in-plane/out-of-plane variation. To date, studies on variation simulation have largely focused on the out-of-plane variation, however the variation generated in the in-plane direction requires more time and efforts to correct afterwards. This research aims to construct a variation simulation model considering both the in-plane and out-of-plane variations. A geometric analysis was performed to derive an equation that reflects the coupling effect of the out-of-plane variation on the in-plane variation. The proposed model is validated with case study analysis and the results shows that good fidelity in predicting and diagnosing the in-plane variation during the block assembly process considering welding distortion.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.221-229
• /
• 1996

The engine speed fluctuation at idle operation mainly comes from cyclic variation of combustion in SI engine. In the present study, engineering model that is representing the cyclic variation of combustion was proposed for the sub-model of the engine cycle simulation. From the observed behaviors of the mass burn rates, probability density functions for the parameters of Wiebe function were defined. The mass burn rate of each cycle is obtained by Monte Cralo perturbation method with the probability function. The simulation results shows that trends of cylinder pressure variation and imep distribution follow up with those of experimental results at idle condition.

• 품질경영학회지
• /
• 제22권4호
• /
• pp.79-101
• /
• 1994

In modern manufacturing, a product consists of many components created by different processes. Variations in the individual component dimensions and in the processes may result in unacceptable final assemblies. Thus, engineers have increased pressure to properly set tolerance specifications for individual components and to control manufacturing processes. When a proper variation stack-up analysis is not performed for all of the components in a functional system, all component parts can be within specifications, but the final assembly may not be functional. Thus, in order to improve the performance of the final assembly, a proper variation stack-up analysis is essential for specifying dimensional tolerances and process control. This research provides a detailed case example of the use of variation stack-up analysis using a Monte Carlo simulation method to improve the defect rate of a complex process, which is the commutator brush track undercut process of an armature assembly of a small motor. Variations in individual component dimensions and process mean shifts cause high defect rate, Since some dimensional characteristics have non-normal distributions and the stack-up function is non-linear, the Monte Carlo simulation method is used.

• 한국환경과학회지
• /
• 제7권5호
• /
• pp.725-733
• /
• 1998

Three numerical experiments are done using IAP(Institute of Atmospheric Physics) global spectral model(T42L9) to investigate the influence of the surface temperatures on the 7-day simulation. Particularly, the response of the subtropical High in summer to the variation of soil temperature and sea surface temperature(SST) was emphasized through a series of experiments. Experiment 1 uses the June climate data as the earth surface conditions. Experiment 2 is similar to Experiment 1 except for the soil surface temperature. Experiment 3 is the same as Experiment 1 except for the modified SST, which is much warmer than the June climate SST on the sea around the Korean peninsula. The main finding in 7-day simulation is that the response of the subtropical high in summer to the variation of the sell surface temperature was much more than that to the variation of the SST. It is implied that the proper treatment of sell surface temperature is more important than that of the SST for the better 7-day simulation of the subtropical high in summer.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.161-168
• /
• 2016

CNG engine has been used as a transportation because of higher thermal efficiency and lower CO2 and particulate matter. However its out put power is decreased due to cylinder-to-cylinder variation during the supply of air-fuel mixture to the each cylinder. It also causes noise and vibration. So in this study, 1D engine simulation model was validated by comparison with experiment data and 3D CFD simulation was conducted to steady-state flow analysis about each manifold geometry. Then, the effects of various intake manifold geometries on variation were evaluated by using 1D-3D coupling analysis at engine speed of 2100 rpm range in 12 L CNG engine. As a result, variation was improved about 4 % though 3D CFD analysis and there was a variation within 3 % using 1D-3D coupling analysis.

• Advances in Computational Design
• /
• 제4권1호
• /
• pp.43-52
• /
• 2019

Variation Analysis (VA) is used to simulate final product variation, taking into consideration part manufacturing and assembly variations. In VA, all the manufacturing and assembly processes are defined at the product design stage. Process Capability Data Bases (PCDB) provide information about measured variation from previous products and processes and allow the designer to apply this to the new product. A new challenge to this traditional approach is posed by the Industry 4.0 (I4.0) revolution, where Smart Manufacturing (SM) is applied. The manufacturing intelligence and adaptability characteristics of SM make present PCDBs obsolete. Current tolerance analysis methods, which are made for discrete assembly products, are also challenged. This paper discusses the differences expected in future factories relevant to VA, and the approaches required to meet this challenge. Current processes are mapped using I4.0 philosophy and gaps are analysed for potential approaches for tolerance analysis tools. Matching points of simulation capability and I4.0 intents are identified as opportunities. Applying conditional variations, incorporating levels of adjustability, and the un-suitability of present Monte Carlo simulation due to changed mass production characteristics, are considered as major challenges. Opportunities including predicting residual stresses in the final product and linking them to product deterioration, calculating non-dimensional performances and extending simulations for process manufactured products, such as drugs, food products etc. are additional winning aspects for next generation VA tools.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제10권4호
• /
• pp.292-299
• /
• 2010

With scaled technology, timing analysis of circuits becomes more and more difficult. In this paper, we review recently developed circuit simulation techniques created to deal with the cost issues of transistor-level simulations. Various techniques for fast SPICE simulations and Monte Carlo simulations are introduced. Moreover, process and aging variation issues are mentioned, along with promising methodologies.

• 전자공학회논문지C
• /
• 제34C권8호
• /
• pp.64-70
• /
• 1997

This paper presents a parameter optimization method using evolutionary programming in voltage reference circuit because the designer must select appropriate parameter values of the circuit taking into consideration both powr voltage and temperature variation. In this paper, evolutionary programming is suggested as an approach for finding good parameters with which the reference voltage variation is small with respect to temperature variation. Simulation results. Simulation results show that this method is effective in circuit design.

• Geomechanics and Engineering
• /
• 제32권3호
• /
• pp.293-305
• /
• 2023

To ensure the safety of underground infrastructures, ground can sometimes be first treated by cement slurry and then stabilized using artificial ground freezing (AGF) technique before excavation. The hydration heat produced by cement slurry increases the soil temperature before freezing and results in an extension of the active freezing time (AFT), especially when the Metro Jet System (MJS) treatment is adopted due to a high cement-soil ratio. In this paper, by taking advantage of an on-going project, a case study was performed to evaluate the influence of MJS and AGF on the ground temperature variation through on-site measurement and numerical simulation. Both on-site measurement and simulation results reveal that MJS resulted in a significant increase in the soil temperature after treatment. The ground temperature gradually decreases and then stabilized after completion of MJS. The initiation of AGF resulted in a quick decrease in ground temperature. The ground temperature then slowly decreased and stabilized at later freezing. A slight difference in ground temperature exists between the on-site measurements and simulation results due to limitations of numerical simulation. For the AGF system, numerical simulation is still strongly recommended because it is proven to be cost-effective for predicting the ground temperature variation with reasonable accuracy.

• 한국멀티미디어학회논문지
• /
• 제22권11호
• /
• pp.1280-1287
• /
• 2019

For developing a wireless implantable device to monitoring the artery variation in real-time. The concept of a special vessel variation measurement capacitive sensor is presented in this paper. The sensor consists of two part; main sensor to measuring the arterial variation, and reference sensor is used to improve the accuracy of the capacitance value variation. Before sensor manufacture, a model of the sensor attached on the artery was designed in 3D to conduct in the FEA simulation to validate the validity and feasibility of the idea. The artery model was designed as layered structures and made of collagenous soft tissues with intima inside, followed by the media and the adventitia. Also, a grease layer was designed in the inner of the arterial wall to imitate the clogged arteries. The simulation was divided into two parts; sensor performance test by changing the diameter of the grease layer, and arterial wall tension test by changing the blood pressure. As the simulation results, the capacitance value measured by the proposed sensor is decreased follow the diameter of the grease increased. Also, large elastic deformation of the arterial wall since changing the blood pressure has been observed.