• Journal of Magnetics
• /
• v.16 no.4
• /
• pp.398-402
• /
• 2011

A novel laminate composite of FeCuNbSiB/FeNi /PZT is proposed, where FeCuNbSiB has a permeability of around 100000, which is much larger than that of FeNi. The high-permeability FeCuNbSiB was laminated with piezomagnetic FeNi rather than attached to its ends. It is expected that the effect produced by the high permeability will act on the whole of the piezomagnetic layer. While a FeNi layer was laminated with a FeCuNbSiB layer, the strong demagnetization produced by the latter was expected to be imposed on the FeNi layer as well as the applied fields. The distribution of applied fields was altered by the high-permeability material (both bias and ac field) and the field variation positively contributed to the ME effect in piezomagnetic/piezoelectric composites. Thus the ME voltage coefficient along with the field sensitivity were improved.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.66-71
• /
• 2012

We deal with a problem to determine experimentally as well as theoretically permeability of incompressible viscous flow through packed bed of bidisperse hard spheres in size. For the size ratios of large to small spheres ${\lambda}$=1.25 and 2, we set up bidisperse packing and measured porosity and permeability at various volumetric ratios of small to large spheres ${\gamma}$. Bidisperse packing shows lower porosity and permeability than monodisperse packing does. Variation of porosity as a function of ${\gamma}$ does not match with that of permeability. A theoretical expression for predicting permeability of a viscous flow for packed bed of bidisperse packing is derived based on calculation of drag force acting on each sphere and its predictions are compared with the experimental data and those from some relations previously suggested. It is found that our theory shows better agreement with experimental results than the previous studies and is proved to be quite simple and accurate in estimating the permeability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.3
• /
• pp.323-331
• /
• 2022

An experimental study was conducted to investigate the effect of applied tensile force and temperature on the permeability of magnetic flux in prestressing steel. The permeability of magnetic flux is the ratio at which the magnetic flux between two points passes. The prestressing steel used in these experiments included a 7-mm PS wire mainly used for cable-stayed bridges and a 12.7-mm PS strand for prestressed concrete bridges. The experiments to extract the permeability of the magnetic flux of steel wire and strand were conducted under various tensile levels and temperature conditions. From the experimental results, it was observed that the permeability of magnetic flux of the PS tension material was linearly proportional to the applied tensile stress level, and inversely proportional to the temperature. If the experimental relationship among the magnetic permeability, temperature, and prestressing ratio of a PS tension material is known in advance, the current tension stress level on PS members can be evaluated by measuring solely the magnetic permeability and temperature.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.552-559
• /
• 2011

There is a method for offering continuous information by AF track circuits. Magnetic fields are formed by current through rails in the AF track circuit systems. So, the continuous information is received by the magnetic fields on a on-board antenna. Coating materials of spray on rails are researched to decrease defects such as head check, shelling, corrugation, squats and so on in Germany. Currently, a coating method of rail construction is proposed by using the ceramics in Korea. When deciding physical characteristic of the coating material of spray, researches are required about variation of flux density and resistivity by using the coating material of spray. In case that the flux density is much lower than existing value, the information for train control is not transmitted to the on-board antenna. In this paper, inductance on rails is calculated and a model is presented about variation of the magnetic field intensity and resistivity in the AF track circuit. Standard permeability of the coating material of spray is proposed. Also, standard resistivity of the coating material of spray is presented by analyzing short current.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.326-332
• /
• 2011

Radial variation of sound absorption capability and air permeability of yellow poplar (Liriodendron tulipifera) wood in cross sectional surface and effect of steam explosion treatment were estimated by the two microphone transfer function method and the capillary flow porometry, respectively. The sound absorption coefficients of steam explosion treated wood was higher than those of control wood and these values increased with frequency. Abundant and big vessel may behave as sound absorbing pore observed on the cross sectional surface of yellow poplar wood. The sound absorption coefficients and air permeability of sapwood were higher than those of heartwood for Liriodendron tulipifera.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.21-26
• /
• 1995

The systematic variation of complex permeability and complex permittivity and their relationship with micro-wave absorbing properties are investigated in sintered Ni-Zn ferrites of non-stoichiometric composition. The specirrens of ${(Ni_{0.5}Zn_{0.5}O)}_{1-x}(Fe_{2}O_{3})_{1+x}$ spinels were prepared by a conventional ceramic processing technique. In the present study. complex permeability and permittivity can be controlled by the variation of ${\alpha}-Fe_{2}O_{3}$ contents in the spinel lattice. The primary effect of the excess ${\alpha}-Fe_{2}O_{3}$ is to increase the dielectric constant. while the notable decrease of magnetic loss is observed in the iron-deficient ferrites. The results suggest that the matching fre-queocyand matching thickness could be controlled by the variation of ${\alpha}-Fe_{2}O_{3}$ contents in the Ni-Zn ferrite.

• Archives of Pharmacal Research
• /
• v.12 no.2
• /
• pp.143-147
• /
• 1989

The urea effect on skin permeation of clonidine was investigated to reduce a log time and to increase a permeability. ICR mouse skin and human skin were used and were assumed to be a two-layer membrane consisted of stratum corneum and viable epidermis. The urea acted as a skin denaturant and humectant in the whole epidermis. Also it enhanced the skin permeability of clonidine about 3.5 times. On the other hand, it enhanced the skin permeability by acting as a humectant in the viable epidermis. But the urea effect on the whole epidermis was shown to be greater than that on the viable epidermis. Therefore, it was found that the effect of urea was greater on the stratum corneum than the viable epidermis. Variation of enhancing effect according to the concentration of urea was not found in the range of 1% to 20%.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.87-90
• /
• 2005

This paper presents an evaluation of the effect of titanium dioxide nanoparticles in sulfonated poly(ether ether ketone) (SPEEK) with sulfonation degree of 57%. A series of inorganic-organic hybrid membranes were prepared with a systematic variation of titanium dioxide nanoparticles content. Their water uptake, methanol permeability and proton conductivity as a function of temperature were investigated. The results obtained show that the inorganic oxide network decreases the proton conductivity and water swelling. It is also found that increase in inorganic oxide content leads to decrease of methanol permeability. In terms of morphology, membranes are homogeneous and exhibit a good adhesion between inorganic domains and the polymer matrix. The properties of the composite membranes are compared with standard nafion membrane.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.18-22
• /
• 2008

The electromagnetic (EM) wave absorption properties with a variation of crystallization annealing temperature have been investigated in a sheet-type absorber using the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy powder. With increasing the annealing temperature the complex permeability (${\mu}_r$), permittivity (${\varepsilon}_r$) and power absorption changed. The EM wave absorber shows the maximum permeability and permittivity after the annealing at $610^{\circ}C$ for 1 hour, and its calculated power absorption is above 80% of input power in the frequency range over 1.5 GHz.

• Geomechanics and Engineering
• /
• v.19 no.4
• /
• pp.361-368
• /
• 2019

This study aims to evaluate the applicability of a grout material that is mixed with carbon fiber, biogrout, ground granulated blast furnace slag (GGBS) powder and cement. Uniaxial compressive strength tests were performed on homo-gel samples at days of 1, 3, 7, 14 and 28. In addition, the variation of permeability with the mixing ratios was measured. Based on the uniaxial compressive strength test, it was confirmed that the uniaxial compressive strength increased by 1.2times when carbon fiber increased by 1%. In addition, as a result of the permeability test, it was found that when the GGBS increased by 20%, the permeability coefficient decreased by about 1.5times. Therefore, the developed grout material can be used as a cutoff grouting material in the field due to its strength and cut-off effect.