• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.747-750
• /
• 2003

We have studied PHEMTs optimization by means of fabrication of PHEMTs. All PHEMTs have been fixed with a gate length of 0.1 ${\mu}{\textrm}{m}$, a gate head size of 0.75${\mu}{\textrm}{m}$, and two gate fingers. We have measured the characteristics of PHEMTs with variation of source-drain spacing, pad size, and gate width. As a result, we have found the enhanced characteristics of $I_{dss}$, $S_{21}$, $h_{21}$, $f_{T}$, $f_{max}$, and $G_{ms}$ with increasing gate width. Also, $g_{m}$ has improved with decreasing source-drain spacing, and $S_{21}$ has improved with deceasing pad size.e.e.e.e.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.11
• /
• pp.723-730
• /
• 2015

This paper investigated the noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time Fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.1
• /
• pp.59-66
• /
• 2003

The purpose of this study is to analyze the characteristics (COP) of the heat pump system for various operating conditions with the use of seawater heat source and exhaust energy. To accomplish the goal, first of all, the computer simulation for heat pump system is carried out. The heat pump system model is made of a waste heat recovery system and a vapor compression refrigeration system, and the working fluid is R-22. The model calculated the change of COP with the variation of temperature and flow rate. The COP and the plate heat exchanger (PHE) area of the heat pump system are considered moderately high in the condensation temperature of $25^{\circ}^C$ and the evaporation temperature of $2^{\circ}^C$ in indoor culture system. The simulation results will be used effectively for the design and the performance prediction of heat pump system using unused energy in a land base aquaculture system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.7 s.100
• /
• pp.865-870
• /
• 2005

Torque fluctuation of the engine and angular velocity variation of propeller shaft is the main excitation source for torsional vibration in the vehicle driveline. Experimental model for engine system is constructed with 4 cylinder 4 cycle diesel engine including Motor-Propeller Shaft-Axle-Wheel system. The angular velocity is measured by magnetic pickup and FV converter at the engine flywheel and propeller shaft. This paper presents the theoretical mechanism of these excitation sources and it is identified by the experimental methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1735-1740
• /
• 2000

The aim of this study is to analyze the sound insulation performance of windows depending on the sound source types and to propose the noise control method in the apartment house. The regions where apartment houses are constructed are varied in the dominant noise sources such as aircraft noise, railway noise and road traffic noise. For the experiment, nine noise sources including pink noise were selected and recorded, which was used in the experiment by reproducing. As a result of this study, the sound insulation performance of window was found that when the frequency contents of the noise were high level in all frequency bands the difference of sound insulation performance was negligible, but when the frequency contents were low level at particular frequency band the difference of sound insulation performance was shown very differently.

• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.71-74
• /
• 2002

We have development the dimming controller using the ac chopper technique. The ac chopper change the amplitude of the input source voltage with the unchanged its frequency. The conventional dimming controller is operated by controlling voltage phase and is consist of the triac. It has a bad characteristic about a current THD and a power factor. But the dimming controller using the at chopper technique has a low current THD and a good power factor. The developed dimming controller is consist of the MOSFET and the low pass filter. The system is operated by the variation circuit of the input source voltage and the microprocessor.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1170-1171
• /
• 2008

Microsources supply high quality power from 1kW to a matter of MW with higher reliability and energy efficiency than the existing large power facilities. In this paper, we designed dynamic modeling of Microturbine and Fuel cell being worthy as a small distributed energy source. Using EMTP we designed the dynamic modeling and confirmed characteristics of steady-state and dynamic analysis. In this paper, we designed dynamic modeling of Microturbine and Fuel cell being worthy as a small distributed energy source and analyzed dynamic characteristics corresponding to load variation.

• Journal of computational fluids engineering
• /
• v.17 no.3
• /
• pp.45-52
• /
• 2012

This paper is a study on the design of the solar lamp bank which is a very important part of the solar simulator with the commercial metal halide lamps and infrared lamps. Lamp Bank is designed by the lamp bank design program based on point light source theory. The reliability of the program for lamp bank design is verified through irradiance variation experiments of a kind of lamp according to horizontal distance. Solar lamp bank facilitates heat distribution and satisfies the irradiance in the three wave length which test guidelines require. The shape of the ceiling board next to the lamp bank to promote the lamp cooling efficiency and to reduce temperature deviation and air velocity deviation in the chamber is so creative. The ceiling board of partial closed type is the best among several types.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.205-212
• /
• 2000

Induction motors. having axial cooling channels in stator and rotor are designed for better cooling performance. Traction motors are one of those examples. And, thermal analysis gain more attention with the Increased demand of the motors, for reliable operation and life prolongation. was Induced to effective thermal conductivity through modeling. Through. fundamental comparison experiment, heat source experiment and transient state experiment, the induction motor using inverter was examined to produce heat source with frequency level and traced to thermal variation at starting and stopping. And thermal analysis using thermal network was compared with a transient state experiment.

• Korean Journal of Microbiology
• /
• v.14 no.4
• /
• pp.167-175
• /
• 1976

Twenty one strains of Rhodopseudomonas palustris from 7 different regions in Korea have been isolated and identified on the basis of Bergey's Manual in order to study their regional variation. They can use fructose as carbon source (or hydrogen donor). Capacity to produce molecular hydrogen during photosynthesis was tested using liquid medium, modified by omission of $NH_4Cl$ and addition of L0glutamic acid. As nitrogen source nitrate can be used, and isopropanol can be used as hydrogen donor. their pH ranges are 5.9 - 9.1. Their growth are inhibited in the medium that contains 100 units of penicillin G/ml. as for the growing test in dark aerobic condition, the period needed for adptation is longer than that of Korea strain of Rhodopseudomonas gelatinosa.