• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.125-130
• /
• 2004

This study proposes a development for the l-kW class small wind turbine system, which is applicable to relatively low wind speed region like Korea and has the variable pitch control mechanism. In the aerodynamic design of the wind turbine blade, parametric studies were carried out to determine an optimum aerodynamic configuration which is not only more efficient at low wind speed but whose diameter is not much larger than similar class other blades. A light composite structure, which can endure effectively various loads, was newly designed. In order to evaluate the structural design of the composite blade, the structural analysis was performed by the finite element method. Moreover both structural safety and aerodynamic performance were verified through the prototype test.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.871-878
• /
• 2003

With the development of micro -technology, the demand for micro actual ing device is increasing. But, it is difficult to achieve high resolution and wide bandwidth with the conventional contact systems. So, the contact-free systems which are suspended or levitated by magnetic force or air bearing were proposed. These systems can be applied to high precision stages and alignment apparatuses. This paper describes a magnetically suspended system with four degrees of freedom which are composed of three rotations (roll, pitch, yaw), and one translation ( z). The operating principle and the structure of the system are similar to variable reluctance type electric machines. In this study, the force analysis is executed using magnetic circuit and virtual work principle, and the equations that describe the dynamics of the system are presented. The multivariable PID controller is adapted to the system and the experiment is executed.

• 대한음성학회지:말소리
• /
• 제53호
• /
• pp.129-141
• /
• 2005

The goal of this research is to improve the quality of reconstructed speech in the Distributed Speech Recognition (DSR) system. For the extended DSR, we estimate the variable Maximum Voiced Frequency (MVF) from Mel-Frequency Cepstral Coefficient (MFCC) based on Gaussian Mixture Model (GMM), to implement realistic harmonic plus noise model for the excitation signal. For the standard DSR, we also make the voiced/unvoiced decision from MFCC based on GMM because the pitch information is not available in that case. The perceptual test reveals that speech reconstructed by the proposed method is preferred to the one by the conventional methods.

• Transactions on Electrical and Electronic Materials
• /
• 제18권5호
• /
• pp.265-272
• /
• 2017

This paper presents the dynamic modeling, analysis, and control of an AC/DC/AC-assisted, self-excited induction generator connected to the grid. The dynamic model includes wind turbine models with pitch control, gear boxes, self-excited induction generators, excitation capacitance, inductive load models, controlled six-pulse rectifiers, and novel state-space models of a grid-connected inverter. The system has been simulated to verify its capabilities of buildup voltage, stator flux response, stator phase current, electromagnetic torque, and magnetizing inductance variation during both the dynamic and steady states with a variable-speed prime mover. The complete setup of the above dynamic models was simulated using MATLAB/SIMULINK.

• Journal of Mechanical Science and Technology
• /
• 제19권10호
• /
• pp.1939-1949
• /
• 2005

Many studies have been conducted to increase regression rate of solid fuel in hybrid rocket. One of them resorts to swirl flow since it can extend the residence time of oxidizer in the fuel grain. Also, metal wires may lead to increase the regression rate of solid fuel as shown in solid propellants. In this study, a series of experiments was designed to investigate the enhancement of regression rate of solid fuel by embedded metal wires and by fuel port grain. And fuel port was designed with a helical configuration to attempt to induce swirl flow. PMMA with gaseous oxygen is the solid fuel used for investigation. Test results showed that embedded metal wires turned out to be ineffective method because only $3-4\%$ increases in regression rate were observed. However, fuel port grain configuration yields higher burning performance of up to $50\%$ increase in regression rate. Also pitch number as well as total impulse was found to be a design variable.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.320-322
• /
• 2002

The paper presents an electrical model of a grid-connected wind energy conversion system (WECS) with a variable speed drive, a fixed pitch angle, a synchronous generator as a wind generator and AC-DC-AC conversion scheme for simulating dynamic behaviors and performance responding to varying wind speed input. The electric output of the WECS is controlled by the AC-DC-AC conversion scheme, the objective of which is to capture the maximum active power under varying wind conditions and to keep the voltage of WECS terminal bus at a specific level. Aerodynamic models are used to incorporate the power characteristics to wind speed. The modeling and simulation of the WECS are realized on PSCAD/EMTDC environment.

• 동력기계공학회지
• /
• 제19권6호
• /
• pp.33-38
• /
• 2015

In this study new CVT(Continuously Variable Transmission) system which is adaptable to a small size electric vehicle is proposed available to gradient response CVT. New pulleys consist of springs adapted driving pulley and driven pulley. At the moment a small electric vehicle drive a slope, new system respond to a gradient as overcoming tensional force of springs. We made prototype of gradient response CVT to test parts performance and travelling performance test. As a result of test, belt pitch diameter varied for high torque direction at the gradient. In the flat travelling, acceleration travelling and gradient travelling performance test, the small electric vehicle with gradient response CVT get improved perfomance than the small electric vehicle with reduction gear.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.31-35
• /
• 1996

The cross section of the circular rod type workpiece to be cut in the band saw machine is variable at every moment in the sawing process. When the cutting feed rate is fixed to the constant speed, the cutting edges of the band saw teeth are also variabl eat any moment, so this causes the wear of the land saw teeth and the deterioration of the quality in the surface roughness. In this study, to work out this kind of problem basically, the mean cutting force of a tooth in the band saw was estimated by using the workpiece which was smaller than the interval of each tooth, i.e. band saw pitch, in the thickness. Then the static cutting forces were predicted by appling the mean cutting forces referred above to the mechanistic cutting force model which were analyzed through the geometric profile of a band saw tooth.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.37.2-37.2
• /
• 2011

Nowadays, offshore wind energy experiences a rapid development because of its wind condition and no noise impact problem. Different from Europe, offshore wind is just started in Asia. More work and research are needed in Korea. In this work, a three-bladed upwind variable speed pitch controlled 5MW wind turbine on a jacket support structure is used. During the simulation, several design load cases are investigated in two different fully coupled aero-hydro-servo-elastic codes. Some critical loads on the foundation are compared and analyzed.

• EDISON SW 활용 경진대회 논문집
• /
• 제4회(2015년)
• /
• pp.217-222
• /
• 2015

In this paper, a study was conducted for the optimization through shear web of shape the Edison program in wind power blade. We measured the displacement and stress distribution through two optimization methods to select the model with the smallest displacement and stress values. Before running the analysis, We try to find the inflection point through the shear web of the model and then analyze by introducing the geometric nonlinearity. The first optimization variables are introduced by the pitch angle and three web shapes. Third model such a honeycomb structure is good way to get an advantage for bending test. According to a method of previous optimization, third model is chosen and then the thickness of the web and blade as a variable is introduced, it is extracted as a result of displacement and the maximum stress per mass.