• 설비공학논문집
• /
• 제25권1호
• /
• pp.43-48
• /
• 2013

In this study, the performance of an impeller according to blade length and pitch angle was studied experimentally by building a variable pitch impeller while changing blade length to review the effect of blade length and pitch angle on a fan's performance. The pitch angle was changed in six steps from $20^{\circ}{\sim}45^{\circ}$ at intervals of $5^{\circ}$ while the blade lengths were changed to 90 mm, 100 mm, 110 mm and 120 mm with an identical airfoil shape while carrying out the experiment. The results are summarized as follows: The air flow per static pressure of axial fans increased linearly with increase of pitch angle, but the high static pressure showed a decrease at a pitch angle of $35^{\circ}$. The shaft power increased proportionally to the pitch angle at all blade lengths; the larger the pitch angle, the larger the measured increase of shaft power. This is because the drag at the fan's front increases with the pitch angle. In the axial fans considered in this research, the flow and increase of static pressure amount increased up to a pitch angle of $30^{\circ}$ but decreased rapidly above $35^{\circ}$.

• Journal of Biosystems Engineering
• /
• 제30권3호
• /
• pp.161-165
• /
• 2005

In this study, peeling test of the Altari radish on kimchi pre-processing system for mechanization was performed with the longitudinal plane peeling type with wider cutting blade than that of the peeled chip's. To determine the optimum cutter shape to match this plane peeling type, the peeling tests depending on variable cutting speed, rake angle and blade angle using the blade with thickness as 2 m and width as 50mm were performed, and the patterns of the peeled chips and peeling resistances were investigated. As the result of the tests, the rake angle of the blade with clean peeled surface of the Altari radish was over $45^{\circ}$, and the blade angle and rake angle with the minimum peeling resistance was $20^{\circ}\;and\;60^{\circ}$, respectively. The optimum peeling conditions were; the peeling speed 0.2m/s, blade angle $20^{\circ}$ and the rake angle $60^{\circ}$, and the peeling resistance of each blade was 15 N.

• International Journal of Fluid Machinery and Systems
• /
• 제8권2호
• /
• pp.94-101
• /
• 2015

To investigate the influence of blade profiles on cavitation behavior in impeller of centrifugal pump, a centrifugal pump with five different blade profiles impellers are studied numerically. The impellers with five different blade profiles (single arc, double arcs, triple arcs, logarithmic spiral and linear-variable angle spiral) were designed by the in-house hydraulic design code using geometric parameters of IS 150-125-125 centrifugal pump. The experiments of the centrifugal pump have been conducted to verify numerical simulation model. The numerical results show that the blade profile lines has a weak effect on cavitation inception near blade inlet edge position, however it has the key effect on the development of sheet cavitation in impeller, and also influences the distribution of sheet cavitation in impeller channels. A slight changing of blade setting angle will induce significant difference of cavitation in impeller. The sharp changing of impeller blade setting angle causes obvious cavitation region separation near the impeller inlet close to blade suction surface and much more flow loss. The centrifugal pump with blade profile of setting angle gently changing (logarithmic spiral) has the super cavitation performance, which means smaller critical cavitation number and lower vapor cavity volume fraction at the same conditions.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.413-414
• /
• 2008

Abstract should be in English. The leaning angle optimization of turbine blade using the genetic algorithm was conducted in this paper. The calculation CFD technique was based upon the Diagonalized Alternating Directional Implicit scheme(DADI) with algebraic turbulencemodeling. The leaning angle of VKI turbine blade was represented using B-spline curve. The control points are the design variable. Genetic algorithm was taken into account as an optimization tool. The objective was to minimize the total pressure loss. The optimized final geometry shows the better aerodynamic performance compared with the initial turbine blade.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.686-689
• /
• 2008

The leaning angle optimization of turbine blade using the genetic algorithm was conducted in this paper. The calculation CFD technique was based upon the Diagonalized Alternating Directional Implicit scheme(DADI) with algebraic turbulence modeling. The leaning angle of VKI turbine blade was represented using B-spline curve. The control points are the design variable. Genetic algorithm was taken into account as an optimization tool. The objective was to minimize the total pressure loss. The optimized final geometry shows the better aerodynamic performance compared with the initial turbine blade.

• 한국산학기술학회논문지
• /
• 제14권7호
• /
• pp.3170-3176
• /
• 2013

본 연구에서는 피치각 가변형 축류팬의 성능(정압별 풍량, 소비전력)과 소음특성을 실험으로 구하였다. 피치각은 $20^{\circ}{\sim}45^{\circ}$로 $5^{\circ}$ 간격으로 6개의 각도를 변화시켜 가면서 측정 하였고 팬 날개는 동일한 에어포일 형상으로 길이는 80 mm, 90 mm, 100 mm, 110 mm, 120 mm로 변경하여 실험을 수행하였다.

• International Journal of Fluid Machinery and Systems
• /
• 제3권3호
• /
• pp.245-252
• /
• 2010

It's known that pump head of centrifugal impeller with lager blade outlet angle is kept higher in air-water two phase flow condition, though the efficiency in water single phase flow condition is inferior. In the present study, a centrifugal impeller with variable blade outlet angles, that has higher efficiencies in both water single phase flow and air-water two phase flow conditions, is proposed. And the performances of the centrifugal impeller with variable blade outlet angles were experimentally investigated in both flow conditions of single and two-phase. In addition, effects of installing diffuser vanes on the performances of centrifugal pump with movable bladed impeller were also examined. The results are as follows: (1) The movable bladed impeller that proposed in this study is effective for higher efficiency in both water single phase and air-water two phase flow conditions. (2) When diffuser vanes are installed, the efficiency of movable bladed impeller decreases particularly at large water flow rate in water single-phase flow condition; (3) The performances of movable bladed impeller are improved by installing of diffuser vanes in air-water two-phase flow condition at relatively small water rate. The improvement by installing of diffuser vanes however disappears at large water flow rate.

• 항공우주시스템공학회지
• /
• 제8권1호
• /
• pp.12-17
• /
• 2014

In this paper, optimal design of composite rotor blade cross-section to consider manufacturability was performed. Skin thickness, torsion box thickness and skin lay-up angle were adopted as discrete design variables and The position and width of a torsion box were considered as continuous variables. An object function of optimal design is to minimize the mass of a rotor blade, and various constraints such as failure index, center mass, shear center, natural frequency and blade minimum mass per unit length were adopted. Finally, design variables such as the thickness and lay-up angles of a skin, and the thickness, position and width of a torsion box were determined by using an in-house program developed for the optimal design of rotor blade cross-section.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.89-95
• /
• 1998

This paper focuses on the effect of structural coupling in the behavior of composite rotor blade. We have searched for bending, extension and shear coupling term with the ply angle of rotor blade and the dynamic behavior of rotor blade for each coupling term. It was found that natural frequency increases as the rotating speed of rotor blade increases. In the couplings with feathering, bending coupling is main parameter, because bending coupling term is larger than shear . Also, the couplings with feathering is less effective in 0$^{\circ}$, 90$^{\circ}$, of ply angle and more variable at blade tip.

• 한국소음진동공학회논문집
• /
• 제23권4호
• /
• pp.338-346
• /
• 2013

Equations of motion of a rotating blade considering pre-twist angle, cross section taper and a concentrated mass are derived using the hybrid deformation variable modeling method. For the modeling of a concentrated mass which is located at an arbitrary position of the blade, a Dirac delta function is employed for the mass density function. The final equations for the vibration analysis are transformed into a dimensionless form using several dimensionless parameters. The effects of the dimensionless parameters on the vibration characteristics of the rotating blade are investigated through numerical analysis.