• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.292-297
• /
• 2009

Air foil thrust bearings are the critical components available on high-efficiency turbomachinery which need an ability to endure the large axial force. Air foil bearings are self-acting hydrodynamic bearings that use ambient air as their lubricant. Since the air is squeezed by the edge of compliance-surface of bearing, hydrodynamic force is generated. In this study, we measured the air film thickness and obtained the minimum film thickness experimentally. To increase the maximum load capacity, compliance of sub-structure was controlled. From numerical analyses, it is seen that, if the air film thickness is distributed more uniformly by variable compliance, the thrust bearings can take more axial load.

• 신재생에너지
• /
• 제3권1호
• /
• pp.13-19
• /
• 2007

A triangular fin with variable fin base thickness and base height is analyzed and optimized for the fixed fin base height using a two-dimensional analytical method. At the middle of the fin length, the variation of the temperature along the fin height is listed. The influences of the fin length, base thickness and base height on the heat loss and fin efficiency are analyzed, The optimum heat loss, corresponding optimum efficiency and optimum fin length as a function of the fin base thickness are presented. The optimum heat loss and optimum fin tip length as a function of the convection characteristic number are represented.

• 전자공학회논문지A
• /
• 제30A권8호
• /
• pp.57-62
• /
• 1993

In this paper, both feasible power gain and power added efficiency at the operating center frequency of 12 GHz are stressed to design a power FET with double-heterjunction structure. The variable parameters or the design are the unit gate width, the gate length, the doping density of AlGaAs, the AlGaAs thickness, the spacer thickness, the Al mole fraction, and the GaAs well thickness. The results of simulation for the FET with 1.mu.m gate length show that the power gain and the power added efficiency are 10.2 dB and 36.3% at 12GHz, respectively. An extrapolation of the relation between current gain and unilateral gain yields a 17 GHz cutoff frequency and 43GHz maximum frequency of oscillation. The calculation of the current versus voltage characteristics show that the output power of the device is about 0.62W.

• 산업기술연구
• /
• 제28권B호
• /
• pp.3-7
• /
• 2008

A cylindrical pin fin with variable fin base thickness is optimized based on fixed outer radius by using the one dimensional analytic method. Heat loss from the pin fin with fixed outer radius is presented as a function of the fin length. The ratio of in length for optimum heat loss to that for the maximum heat loss is listed. The maximum heat loss and effectiveness and the fin length for the optimum heat loss are presented as a function of fin base thickness and outer radius. One of the results presents the maximum effectiveness decreases rapidly first and then decreases slowly as the fin outer radius increases.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권4호
• /
• pp.381-386
• /
• 2013

A new resistance model for a Schottky Barrier Diode (SBD) in CMOS technology is proposed in this paper. The proposed model includes the n-well thickness as a variable to explain the operational behavior of a planar SBD which is firstly introduced in this paper. The model is verified using the simulation methodology ATLAS. For verification of the analyzed model and the ATLAS simulation results, SBD prototypes are fabricated using a $0.13{\mu}m$ CMOS process. It is demonstrated that the model and simulation results are consistent with measurement results of fabricated SBD.

• 수산해양기술연구
• /
• 제22권1호
• /
• pp.49-57
• /
• 1986

The vibrations problem of thin orthotropic skew plates of linearly varying thickness is analyzed using the small deflection theory of plates. Using dimensionless oblique coordinates, the deflection surface can be expressed as a polyonmial series satisfying the boundary conditions. For orthotropic plates which is clamped on all the four edges, numerical results for the first two natural frequencies are presented for various combinations of aspect ratio, skew angle and taper parameter. The properties of material used are one directional glass fibre reinforced plastic GFRP. The results obtained may be summarised as follows: 1. In case of the first mode vibration of plates with increase in the skew angle, the natural frequencies of plates decrease. 2. As the aspect ratio decrease, the natural frequencies of plates decrease. 3. For the identical skew angle, natural frequencies of plates increase with the taper parameter of thickness.

• Smart Structures and Systems
• /
• 제19권4호
• /
• pp.441-448
• /
• 2017

This paper uses the four-variable refined plate theory for the free vibration analysis of functionally graded material (FGM) rectangular plates. The plate properties are assumed to be varied through the thickness following a simple power law distribution in terms of volume fraction of material constituents. The theory presented is variationally consistent, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. Equations of motion are derived from the Hamilton's principle. The closed-form solutions of functionally graded plates are obtained using Navier solution. Numerical results of the refined plate theory are presented to show the effect of the material distribution, the aspect and side-to-thickness ratio on the fundamental frequencies. It can be concluded that the proposed theory is accurate and simple in solving the free vibration behavior of functionally graded plates.

• Structural Engineering and Mechanics
• /
• 제60권2호
• /
• pp.313-335
• /
• 2016

In this article, a four-variable refined plate theory is presented for buckling analysis of functionally graded plates subjected to uniform, linear and non-linear temperature rises across the thickness direction. The theory accounts for parabolic distribution of the transverse shear strains, and satisfies the zero traction boundary conditions on the surfaces of the plate without using shear correction factor. Young's modulus and Poisson ratio of the FGM plates are assumed to remain constant throughout the entire plate. However, the coefficient of thermal expansion of the FGM plate varies according to a power law form through the thickness coordinate. Equilibrium and stability equations are derived based on the present theory. The influences of many plate parameters on buckling temperature difference such ratio of thermal expansion, aspect ratio, side-to-thickness ratio and gradient index will be investigated.

• 한국구조물진단유지관리공학회 논문집
• /
• 제28권2호
• /
• pp.17-26
• /
• 2024

최근 콘크리트 타설 중 구조체, 거푸집 및 동바리 사고가 계속해서 발생하고 있으며, 특히 슬래브 두께가 증가하는 다층지지 RC 구조에서 붕괴 사고가 빈번하게 발생하였다. 이전 연구에서는 모든 슬래브 두께가 일정한 경우에 대한 연구가 주로 수행되었으나 일부 슬래브의 두께가 다른 경우, 슬래브 단면 강성의 변화로 전체 슬래브 강성 비율이 달라져 시공 하중의 분포가 달라질 수 있어 이에 대한 연구가 요구된다. 이 연구에서는 슬래브 두께를 변수로 설정하여 슬래브 두께 변화가 콘크리트 강성과 구조물에 미치는 영향을 고려하여 시공 하중의 분포를 분석하였으며, 슬래브 두께가 변화하는 경우 콘크리트 재료 강성 뿐만이 아닌 슬래브 단면 강성도 시공 하중 산정에 고려되어야 함을 확인하였다. 슬래브 두께가 증가 할 경우 두께가 증가하는 층에 작용하는 최대 시공 하중과 최대 손상 변수는 크게 증가하였으며 두께 증가가 클수록 더욱 높은 비율의 시공 하중이 작용함을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제67권6호
• /
• pp.565-578
• /
• 2018

This research article reported the nonlinear finite solutions of the nonlinear flexural strength and stress behaviour of nano sandwich graded structural shell panel under the combined thermomechanical loading. The nanotube sandwich structural model is derived mathematically using the higher-order displacement polynomial including the full geometrical nonlinear strain-displacement equations via Green-Lagrange relations. The face sheets of the sandwich panel are assumed to be carbon nanotube-reinforced polymer composite with temperature dependent material properties. Additionally, the numerical model included different types of nanotube distribution patterns for the sandwich face sheets for the sake of variable strength. The required equilibrium equation of the graded carbon nanotube sandwich structural panel is derived by minimizing the total potential energy expression. The energy expression is further solved to obtain the deflection values (linear and nonlinear) via the direct iterative method in conjunction with finite element steps. A computer code is prepared (MATLAB environment) based on the current higher-order nonlinear model for the numerical analysis purpose. The stability of the numerical solution and the validity are verified by comparing the published deflection and stress values. Finally, the nonlinear model is utilized to explore the deflection and the stresses of the nanotube-reinforced (volume fraction and distribution patterns of carbon nanotube) sandwich structure (different core to face thickness ratios) for the variable type of structural parameter (thickness ratio, aspect ratio, geometrical configurations, constraints at the edges and curvature ratio) and unlike temperature loading.