• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.63-73
• /
• 1993

In this paper, fuzzy control algorithm for the speed ratio control of the electro-hydraulic rig type continuously variable transmission(CVT) was proposed and the CVT performance tests were carried out for the optimal operation of the engine simulator. The experimental results for the constant throttle and the acceleration modes showed that the engine can be run on the optimum operating line, representing the power and economy mode, by the fuzzy control of the CVT speed ratio. Comparing the PID control with the fuzzy control, it was found that the fuzzy control showed better performance with the faster rising time and smaller steady state error. The result of this study can be used as basic design materials for developing the transmission control unit of the CVT.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.780-786
• /
• 2001

For the compressor speed control of a multi-type air conditioning system, a fuzzy control algorithm was developed. The sum of zone temperature errors and its derivative were used as input variables, and the compressor speed was selected as the output variable. To test the effectiveness of the control algorithm, one outdoor environmental chamber and four indoor environmental chambers were used. In the chambers the zone temperature step change test and the indoor unit change over test were performed. Test results showed that, for the control of compressor speed, the fuzzy control algorithm was more effective than the conventional proportional control algorithm for the energy conservation.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.75-82
• /
• 2012

Elimination of rotor position sensors mechanically coupled with the rotor shaft is attractive to variable speed drives primarily due to increased system reliability and cost reduction. In this regard, search for a simple and robust position sensorless control has been intensified in past few years specifically for low-cost, high-volume applications such as home appliances. This paper describes a new parameter insensitive position sensorless control for switched reluctance motor (SRM) drives satisfying such a need in this market segment. Two consecutive switch-on times of the controllable switch in hysteresis current control are compared to estimate the rotor position and speed. The proposed sensorless control algorithm is very simple to implement since it does not depend on extensive computation or any additional hardware. In addition, the proposed method is robust in that its dynamic performance is least affected by system parameter variations. The proposed approach is demonstrated on a single-controllable-switch-converter-driven SRM with two-phases that lends itself to a system with low cost and compact packaging which comes close to the intended applications. Analysis and simulation results followed by experimental verification are presented to demonstrate the feasibility of the proposed sensorless control method.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.264-269
• /
• 2011

A precision of temperature control in the manufacturing process would be an important factor and become the main key to control production quality. Mostly manufacture machinery used oil as a coolant in their system so an accurate oil temperature control system become an absolute need in industrial field. This paper presents a experiment research to control the oil temperature constant at target point, in this experiment is $35^{\circ}C$ by using an inverter attached in compressor to varying the compressor speed. This control has been completed and tested through an experiment with different heat load of 4kW, 6kW, 7kW, 8kW and 10kW given under temperature constant room conditioned as $25^{\circ}C$. The results had shown the temperature deviation in the refrigerator has around $0.2^{\circ}C$ and the COP is 2.5 gained at 8kW and 10kW.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.2
• /
• pp.23-28
• /
• 1983

In this paper, a method to control the speed of a dc motor using a phase locked loop circuit with a variable sequential filter is discussed. We improved the transient response time more than 15 percent compared to conventional system using a variable sequential filter and the steady state error was reduced to less than 0.05 percent per rotation axis.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.80-87
• /
• 2003

Micro gas turbines are designed with low turbine inlet temperature and pressure ratio. To overcome the efficiency defect of the simple cycle, adoption of the recuperator is an inevitable choice. In addition to the design performance, we should also pay attention to the off-design performance of gas turbines since they usually operate at part-load conditions for a considerable amount of the time. This study aims at analyzing off-design performance characteristics of micro gas turbines and addressing the importance of the recuperator in the part load operation. Comparative analyses have been performed to evaluate the part load performance differences among various design and operating options : simple vs recuperative cycles, single vs two shaft configurations, various operating strategies for the single shaft configuration (fuel only control, variable speed operation, variable inlet guide vane control), and current vs advanced engines. Major finding is that maintaining turbine at high level is crucial in efficient operation of micro gas turbines.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2268-2270
• /
• 2003

In this paper, mathematically modeled equations were derived for wind turbine under the analysis of aerodynamics. On the basis of these equations, maximum power controller is implemented by simulink in matlab. In order to achieving maximum power, variable speed control method is used for obtaining maximum power coefficient in the variable wind speed because we can have maximum changing efficiency in these coefficients. Also, the maximum power control of wind generator system uses a synchronous generator and a invertor circuit.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.169-173
• /
• 2011

This study is about the development of remote controlled bollard using the BLDC motor and ball screw with mechatronics theory. A bollard is composed of the sensor part and the control part. The sensor part is consisted of sensors that detect the locations of a bollard. The role of the control part is adjusting motor speed and power through variable resistance. In order to confirm required performance, the speed of decent and ascent of the bollard, the time and the RPM of BLDC motor were tested according to the variable resistance and the applied load with 10 to $72kg_f$.

• ETRI Journal
• /
• v.6 no.2
• /
• pp.3-9
• /
• 1984

This paper proposes an optimal control scheme for shaft position control using microcomputer-based state-variable feedback. In this scheme a performance index was set up in order to ruduce the overshoot and improve the steady- state response speed, and the time-variant system parameters were identified in real time for optimal control. As a result of experiment, the over-shoot was not occured and the response speed was improved 2. 9 times about proportional control. This scheme improves the performance against the variation of load and sampling time, and adding the integral control in this scheme can reduce the steady-state error without any change in response time.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.485-487
• /
• 2006

Speed and torque controls of permanent magnet synchronous motors are usually attained by the application of position and speed sensors. However, speed and position sensors require the additional mounting space, reduce the reliability in harsh environments and increase the cost of a motor. Therefore, many studies have been performed for the elimination of speed and position sensors. This paper investigates an Improved sliding mode observer for the speed sensorless control of a permanent magnet synchronous motor. The proposed control strategy is the sliding mode observer with a variable boundary layer for a low-chattering and fast-reponse control. The proposed algorithm is verified through the simulation and experimentation.