• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1875-1882
• /
• 1993

Variable thickness plates are commonly used as structural members in the majority of industrial sectors. Previous fracture mechanics researches on variable thickness plates were limited to mode I loading cases. In practice, however, cracks are usually located inclined to the loading direction. In this respect, combined mode(mode I/II) stress intensity factors $K_{I}$ and $K_{II}$ at the crack tip for a variable thickness plate were obtained by 3-dimensional finite element analysis. Variable thickness plates containing a slant edge crack were chosen. The parameters used in this study were dimensionless crack $length{\lambda}$, slant $angle{\alpha}$, thickness $ratio{\beta}$ and width ratio{\omega}$. Stress intensity factors were calculated by crack opening displacement(COD) and crack sliding displacement(CSD)method proposed by Ingraffea and Manu.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.53-60
• /
• 2014

This paper proposes a control scheme to reduce the power consumption of a variable displacement swash-plate type piston pump supplying oil to a valve-controlled hydraulic cylinder at constant pressure. Whenever flow rate demand was absent, the swash plate angle and the pump speed were changed to the minimum values required to compensate for the internal leakage flow. In response to command signals, the pump speed was changed in proportion to the absolute mean value of the speed component for position commands. At the same time, a pressure regulator was activated to maintain constant system pressure by precisely adjusting the pump speed with the swash plate angle fixed at the maximum. The conventional system consisting of a pressure-compensated variable displacement type pump is driven at a constant speed of 1,800rpm. By comparison, computer simulation and experimental results showed that idling power at stand-by status could be reduced by up to 70% by reducing the pump speed from 1,800rpm to 300rpm and the swash plate angle to the minimum.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.1
• /
• pp.73-94
• /
• 2003

The purpose of this investigation was to analyze A kinematic analysis of the Kuzushi-arm motion when performing Morote-Seoinage in judo who was 5 females university representative judokas of light weight category in judo, and filmed on video cameras(60field/s). The data of this study digitizied by KWON3D 2.1 program computed the average and standard deviation calculated individual 5 trials with Programing Lab view 6i. From the data analysis & discussion, the following conclusions were drawn : 1) distance variable of attacking hand arm in kuzushi motion Left right(X direction) displacement variable was all of A, B, C pattern with moving left to right and leaning. Strip of displacement variable was ordo. to C(55.6cm), A(53.3cm), B(43.9cm) pattern, C pattern largely leaned to left Front Rear(Y direction) displacement variable was different A($131.3cm{\pm}3.1cm$), B($128.7{\pm}4.0cm$) and C(111.0cm) on ready position, 3 pattern leaned to rear direction. Strip of displacement was order to B(43.4cm), A(41.1cm) and C pattern(28.3cm). Up down(Z direction) displacement variable was all of A, B, C pattern leaned to up in the Kuzushi-phase and leaned to down in the Kake-phase. Strip of displacement was order to A(83.9cm), B(80.4cm), C pattern(71.9cm). 2) Shoulder joint angle variable Flexion and extension Ready position' angle was A($138.3{\pm}4.9^{\circ}$), B($142.9{\pm}3.7^{\circ}$) and C($164.5^{\circ}$) pattern, strip of flexion extension was order to C($80.9^{\circ}$), A($79.9^{\circ}$) and B($39.0^{\circ}$) pattern, greatly C pattern had largely angle change. Adduction and abduction : B and C pattern's angle change were adduction and abduction in the Kuzushi-phase after adduction in the Kake phase, A pattern's angle change was abduction in the Kuzushi-phase after adduction in the Kake phase. internal and external rotation : 3 pattern were internal rotation in the Tsukuri phase and external rotation in the Kake phase. After B and C pattern were external rotation and A pattern was internal rotation. 3) Elbow joint angle variable Flexion and extension 3 pattern's ready position angle were A($142.0{\pm}4.4^{\circ}$), B($123.5{\pm}5.5^{\circ}$) and C($105.5^{\circ}$) and flexion. Strip of flexion extension were order to A($57.9^{\circ}$), C($34.6^{\circ}$) and B($25.2^{\circ}$) pattern.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.190-195
• /
• 1998

This paper reports on the theoretical and expetimental study of the vane and cam ring motions in a variable displacement vane pump which is already used widely in various industrial and automotive applications. Dynamic equations of vane and cam ring motion and flow continuity equations are derived and then solved simultaneously using the numerical method. Vane detachment cause the pressure tipples, noise, wear in cam ring, and decrease the volumetric efficiency. Consequently, Vane detachment occurs due to excess compression in the pumping chamber, and it can be reduced by adjustment of design parmeters.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.272-276
• /
• 1996

This study deals with the speed control of an overcentered variable-displacement hydraulic motor on a constant pressure network, which is noted for its high system efficiency fast dynamic response and energy recovery capability. The speed control characteristics of the conventional cascade PI controller are largely affected by load-torque disturbances. To obtain robust speed control despite torque disturbances, the load torque is estimated by an observer based on a mathematical model and compensated for by a feedforward loop. It is shown by experiment that robust speed control may be obtained with the proposed controller. The experimental data agree fairly well with the theoretical analysis.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.1 no.4
• /
• pp.9-14
• /
• 2004

An estimation technique called the Extended Kalman filter is used to estimate viscous friction, spring initial contraction, and the spring constant on the swash plate of a variable displacement pump. The feasibility of the approach was established using a simulation study. It showed that these parameters could be estimated very accurately in a reliable and independent fashion. A special experimental system was set up to facilitate the measurement of certain states to enhance the Kalman Filtering approach. The aforementioned parameters were estimated and found to be reasonably repeatable for a common operating point. It was very evident that as the operating conditions changed (i.e. temperature) so did the estimated values of certain parameters such as viscous friction. This was believed to be a good verification test for the approach.

• Journal of the Korean Society of Safety
• /
• v.13 no.3
• /
• pp.24-31
• /
• 1998

Variable thickness plates are commonly encountered in the majority of mechanical/structural components of industrial applications. And, as a result of the unsymmetry of the structure or the load and the anisoptropy of the materials, the cracks in engineering structures are generally subjected to combined stresses. In spite of considerable practical interest, however, a few fracture mechanics study on combined mode crack in a variable thickness plate have carried out. In this respect, combined mode I/III stress intensity factors $K_I$ and $K_III$ at the crack tip for a variable thickness plate were obtained by 3-dimensional finite element analysis. Variable thickness plates containing a central slant crack were chosen. The parameters used in this study were dimensionless crack length $\lamda$, crack slant angle $\alpha$, thickness ratio $\beta$ and width ratio $\omega$. Stress intensity factors were calculated by crack opening displacement(COD) and crack tearing displacement(CTD) method.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2142-2153
• /
• 2014

Linearization of transducer characteristic plays a vital role in electronic instrumentation because all transducers have outputs nonlinearly related to the physical variables they sense. If the transducer output is nonlinear, it will produce a whole assortment of problems. Transducers rarely possess a perfectly linear transfer characteristic, but always have some degree of non-linearity over their range of operation. Attempts have been made by many researchers to increase the range of linearity of transducers. This paper presents a method to compensate nonlinearity of Linear Variable Displacement Transducer (LVDT) based on Extreme Learning Machine (ELM) method, Differential Evolution (DE) algorithm and Artificial Neural Network (ANN) trained by Genetic Algorithm (GA). Because of the mechanism structure, LVDT often exhibit inherent nonlinear input-output characteristics. The best approximation capability of optimized ANN technique is beneficial to this. The use of this proposed method is demonstrated through computer simulation with the experimental data of two different LVDTs. The results reveal that the proposed method compensated the presence of nonlinearity in the displacement transducer with very low training time, lowest Mean Square Error (MSE) value and better linearity. This research work involves less computational complexity and it behaves a good performance for nonlinearity compensation for LVDT and has good application prospect.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.33-38
• /
• 2010

Technology of vehicle industry has been developing and it is required a better vehicle performance than before. Therefore, the consumers are asking not only an economic efficiency, functionality, polished design, ride comfort and silence but also a driving stability. The ride comfort, silence and driving stability are influenced by the size of vehicle and various facilities. But the principal factor is a room noise and vibration sensed by a driver and passenger. Thus, the NVH of vehicle has been raised and used as a principal factor for evaluation of vehicle performance. The primary objective of this study is an optimized design of powertrain mounting system. To optimized design was applied MSC.Nastran optimization modules. Results of dynamic analysis for powertrain mounting system was investigated. By theses results, design variables was applied 12 dynamic spring constant. And the weighting factor according to translational displacement and rotational displacement applied 3 cases. The objective function was applied to minimize displacement of powertrain. And the design variable constraint was imposed dynamic spring constant ratio. The constraint of design variable for objective function was imposed bounce displacement for powertrain.

• Smart Structures and Systems
• /
• v.6 no.8
• /
• pp.953-974
• /
• 2010

The performance of variable dampers for seismic protection of the benchmark highway bridge (phase I) under six real earthquake ground motions is presented. A simplified lumped mass finite-element model of the 91/5 highway bridge in Southern California is used for the investigation. A variable damper, developed from magnetorheological (MR) damper is used as a semi-active control device and its effectiveness with friction force schemes is investigated. A velocity-dependent damping model of variable damper is used. The effects of friction damping of the variable damper on the seismic response of the bridge are examined by taking different values of friction force, step-coefficient and transitional velocity of the damper. The seismic responses with variable dampers are compared with the corresponding uncontrolled case, and controlled by alternate sample control strategies. The results of investigation clearly indicate that the base shear, base moment and mid-span displacement are substantially reduced. In particular, the reduction in the bearing displacement is quite significant. The friction and the two-step friction force schemes of variable damper are found to be quite effective in reducing the peak response quantities of the bridge to a level similar to or better than that of the sample passive, semi-active and active controllers.