• 산업기술연구
• /
• 제2권
• /
• pp.13-19
• /
• 1982

Polycrystalline silicon layers have been deposited by a chemical vapor deposition technique using $SiCl_4$, $H_2$ gas mixture on single crystal silicon substrates. In this work, the effects of depostion temperature and total flow rate on the deposition rate of polycrystalline silicon are investigated. From the experimental results it was found that the formation reaction of polycrystalline silicon was limited by surface reaction and mass transfer controlled as the deposition temperature was increased. The morphology of polycrystalline silicon layer changed from a fine structure to a coarse one as the deposition temperature was increased.

• Bulletin of the Korean Chemical Society
• /
• 제20권9호
• /
• pp.1031-1034
• /
• 1999

Tin oxide films have been grown employing the chemical vapor deposition technique under reduced pressure conditions using tetramethyltin as the precursor and oxygen as the oxidant. An activation energy derived for the deposition reaction under representative deposition conditions has a value of 89±3 kJ mol-1, suggesting a typical kinetic control. Deposition rates of tin oxide films exhibit a near first order dependence on tetramethyltin partial pressure and a zeroth order dependence on oxygen partial pressure. This study provides the first quantitative information about the growth kinetics of tin oxide films from tetramethyltin by the cold-wall low-pressure chemical vapor deposition.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2006년도 제30회 학술논문발표회 초록집
• /
• pp.186-186
• /
• 2006

• 한국초전도ㆍ저온공학회논문지
• /
• 제13권4호
• /
• pp.5-9
• /
• 2011

We have fabricated the superconducting $MgB_2$/carbon fiber by physical vapor deposition method. Mg (Magnesium) and B (Boron) were simultaneously deposited on the carbon fiber using the RF-sputtering and thermal evaporation, respectively. To ensure the relatively high vapor pressure of Mg at the growth region and the subsequent phase stability of $MgB_2$ at the deposition temperature, inverted funnel-like guide made of Mg-foil was employed while one side of the guide were open for the sputtered B flux. Mg vapor pressure should be controlled precisely to secure the complete reaction. The $MgB_2$/carbon fiber showed a uniformly deposited thin layer with dense and well-formed grains. The $MgB_2$/carbon fibers in this study showed $T_c$~37.5K, $J_c$ ~ $2{\times}10^4\;A/cm^2$ in the 20K, 0T.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.381-381
• /
• 2011

The influence of the water vapor on the growth of single-walled carbon nanotubes (SWCNTs) was investigated. SWCNTs were synthesized by catalytic chemical vapor deposition of acetylene over Fe-Mo/MgO catalyst with injection of water vapor. The morphologies and structures of the water-assisted SWCNTs were investigated according to the growth conditions such as water vapor concentrations, flow rate of the gas, furnace temperature, and growth time. Water-assisted SWCNTs exhibited large bundle morphological features with well-alignment of each CNT, while SWCNTs synthesized in the absence of water vapor showed entangled CNT with the random orientation. We also found that the diameter of the SWCNT bundle could be controlled by the growth condition. In our optimal growth condition, the product yield and the purity were 300 wt. % and 75%, which were 7.5 and 2.5 times higher than those of SWCNTs synthesized without water vapor, respectively. More detail discussion will be offered at the poster presentation.

• 한국표면공학회지
• /
• 제23권2호
• /
• pp.18-23
• /
• 1990

Thin films of tin oxide were prepared by chemical vapor deposition (C.V>D) using the hydrolysis reaction of SnCl4, Deposition rate increased with the increase of temperature up to $500^{\circ}C$and then decreased at $700^{\circ}C$, Deposition rate with SnCl4 partial pressure showed RidealEley behavir. It was found that SnO2 thin film deposited at the temperature above $400^{\circ}C$ had(110) and (301) plane preferred orientation with crystallinity of rutite structure. Electrical resisvity of SnO2 thin film decreased with increase increase of deposition temperature and showed minimum value of 10-3 ohm at $500^{\circ}C$and than largely increased increased with further increase of deposition temperture.

• 한국결정성장학회지
• /
• 제17권1호
• /
• pp.18-22
• /
• 2007

Carbon nanofilaments were deposited on silicon oxide substrate by thermal chemical vapor deposition method. We used $Fe(CO)_5$ as the catalyst for the carbon nanofilaments formation. Around $800^{\circ}C$ substrate temperature, the formation density of carbon nanofilaments could be enhanced by the vacuum sublimation technique of $Fe(CO)_5$, compared with the conventional spin coating technique. Finally, we could achieve the low temperature, as low as $350^{\circ}C$, formation of carbon nanofilaments using the sublimated Fe-complex nanograins with thermal chemical vapor deposition. Detailed morphologies and characteristics of the carbon nanofilaments were investigated. Based on these results, the role of the vacuum sublimation technique for the low temperature deposition of carbon nanofilaments was discussed.

• 한국전기전자재료학회논문지
• /
• 제29권4호
• /
• pp.241-246
• /
• 2016

ZnO thin films have wide application areas due to its versatile properties as transparent conductors, wide-bandgap n-type semiconductors, gas sensor materials, and etc. We have performed a systematic investigation on ultraviolet-assisted CVD (chemical vapor deposition) method. Ultraviolet irradiation during the deposition of ZnO causes chemical reduction on the growing surface; which results in the reduction of the deposition rate, increase in the surface roughness, and decrease of the electrical resistivity. These effects produce larger characteristic variation with various deposition conditions in terms of surface morphology and optical/electrical properties compared to normal CVD deposited ZnO thin films. This versatile controllability of ultraviolet-assisted CVD can provide a larger processing options in the fabrication of nano-structured materials and flexible device applications.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.647-651
• /
• 2016

SiC films were prepared on glassy carbon substrates by laser chemical vapor deposition under a high pressure of $10^4Pa$ using a diode laser (wavelength = 808 nm) and a polysilaethylene precursor. (111)-oriented SiC films were formed at a deposition temperature ($T_{dep}$) range of 1150 - 1422 K. At $T_{dep}=1262K$, the SiC film with a high Lotgering factor of above 0.96 showed an exhibited pyramid-like surface morphology and flower-like grains. The highest deposition rate ($R_{dep}$) was $220{\mu}m\;h^{-1}$ at $T_{dep}=1262K$.

• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.809-814
• /
• 1998

In this study, the metastable state diamond thin films have been deposited on Si substrates from methand-hydrogen and oxygen mixture usin gMicrowave Plasma Enhanced Chemical Vapor Deposition (MWPCVD) method. effects experimental parameters MWPCVD including methan concentrations, oxygen additions, operating pressure, deposition time on the growth rate and crystallinity were investigated. diamond thin film was synthesized under the following conditions: methane concentration of 0.5%(0.5sccm)∼5%(5sccm). oxygen concentration of 0∼80%(2.4sccm). operating pressure of 30Torr∼ 70Torr, deposition time of 1∼32hr. SEM, WRD, and Raman spectroscopy were employed to analyse the growth rate and morphology, crystallinity and prefered growth direction, and relative amounts of diamond and non=diamond phases respectively.