• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2001년도 춘계연구발표회 논문개요집
• /
• pp.46-47
• /
• 2001

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.221-224
• /
• 2012

This paper presents the strength safety of a hybrid alarm valve by a finite element analysis. The stress and strain of a conventional hybrid alarm valve are calculated for the given maximum test pressure of 2MPa. Especially, the FEM computed maximum stress of a conventional hybrid valve is only 18.6% of yield strength, 370MPa. This means that the conventional valve is designed with a thick thickness of a valve structure. But, new hybrid alarm valve model, which is developed by optimized design method in this study, shows more low level of 43% in maximum stress and strain compared with that of a conventional hybrid valve. These results may recommend the reduction of a weight and a dimension for an optimized hybrid alarm valve.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.1051-1054
• /
• 2000

We developed the micro CSF (celebrospinal fluid) shunt valve with surface and bulk micromachining technology in polymer MEMS. This micro CSF shunt valve was formed with four micro check valves to have a membrane connected to the anchor with the four bridges. The up-down movement of the membrane made the CSF on & off and the valve characteristic such as open pressure was controlled by the thickness and shape of the bridge and the membrane. The membrane, anchor and bridge layer were made of the $O_2$ RIE (reactive ion etching) patterned Parylene thin film to be about 5~10 microns in thickness on the silicon wafer. The dimension of the rectangular nozzle is 0.2＊0.2 $\textrm{mm}^2$ and the membrane 0.45 mm in diameter. The bridge width is designed variously from 0.04 mm to 0.12 mm to control the valve characteristics. To protect the membrane and bridge in the CSF flow, we developed the packaging system for the CSF micro shunt valve with the deep RIE of the silicon wafer. Using this package, we can control the gap size between the membrane and the nozzle, and protect the bridge not to be broken in the flow. The total dimension of the assembled system is 2.5＊2.5 $\textrm{mm}^2$ in square, 0.8 mm in height. We could precisely control the burst pressure and low rate of the valve varing the design parameters, and develop the whole CSF shunt system using this polymer MEMS fabricated CSF shunt valve.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.184-192
• /
• 2001

Cam/tappet wear is one of the critical concerns in valve train deign. Maximum contact stress and minimum oil film thickness between the cam and tappet are usually checked for the estimation of wear characteristics. If the two extreme cases arise simultaneously, there is a strong possibility of cam/tappet wear. In this paper, effects of valve train layout on the wear characteristics were studied. Especially for swinging arm type valve trains, initial geometric layout must be very carefully defined to avoid wear problems. The study was performed fur an end pivot type OHC valve train, which had severe wear problems. Analysis results show that some geometric parameter affect very sensitively on the wear characteristics. Experiments were also performed for the original and modified valve trains, which strongly support the analysis results.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1993년도 추계학술대회
• /
• pp.99-103
• /
• 1993

A monoleaflet polymer artificial heart valve which showed the remarkable improvement in pressure drop compared with other types of artificial valve was designed to decrease the deflection in vertical direction and the displacement or the valve tip in horizontal direction. Stress distribution change was studied as the location of the supporting members or the valve frame changed. And it was found that using the valve tip horizontal displacement the minimum valve thickness could be obtained in order to prevent the gap between the valve tip and the frame wall.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.655-663
• /
• 2005

Tribological characteristics in the sliding parts of oil hydraulic piston pumps are very important in increasing overall efficiency. In this study, the fluid film between the valve plate and the cylinder block was measured by using a gap sensor and the mercury-cell slip ring unit under real working conditions. To investigate the effect of the valve shape, we designed three valve plates each having a different shape. One of the valve plates was without bearing pad, another valve plate had bearing pad and the last valve plate was a spherical valve plate. It was noted that these three valve plates observed different aspects of the fluid film characteristics between the cylinder block and the valve plate. The leakage flow rates and the shaft torque were also investigated in order to clarify the performance difference between these three types of valve plates. From the results of this study, we found that the spherical valve plate estimated good fluid film patterns and good performance more than the other valve plates in oil hydraulic axial piston pumps.

• Tribology and Lubricants
• /
• 제20권3호
• /
• pp.132-139
• /
• 2004

Many researches about the contacts between cam and follower have investigated EHL film thickness either without dynamic loading effect or only with curve fitting formula such as Dowson-Hamrock's, because including squeeze film effect makes it hard to obtain convergence and stability of computation. Therefore, inaccurate information about minimum film thickness without dynamic loading condition causes inappropriate design of cam profiles and wrong selection of cam and follower materials. In this work, computation tools both for kinematics and dynamics of valve train system of push-rod type and for fluid film thickness with elastic deformation on the basis of dynamic loading condition with multigrid multi-level method is developed. The computational results of minimum film thickness with the respects of both static and dynamic loading conditions are compared for the contact of flat follower over the entire cycle.

• Design & Manufacturing
• /
• 제13권1호
• /
• pp.31-35
• /
• 2019

For manufacturing upper housing product of mechanical control valve, the progressive drawing process was conducted experimental. Then, the center of the product was cut to measure the thickness of the product. As a result, the following conclusions were obtained. By means of a stand-alone pad provided with sufficient pressure, it is possible to prevent the occurrence of wrinkles in the die pad product of the drawing process. As a result of the experiment, it was considered that the flange bottom of the product and the lower edge of the product are made thick in thickness, the top edge and the top surface are thin. It is considered that this is due to the size and roughness of the entrance edge radius of the die in the drawing process, and the inflow of the material by the die pad.

• 한국화재소방학회논문지
• /
• 제16권4호
• /
• pp.59-64
• /
• 2002

버터플라이 밸브의 압력손실과 캐비테이션에 대한 유동특성 연구를 수행하였다. 밸브의 열림각에 대한 압력손실계수는 Carnot 방정식을 응용하여 수식화하였다. 캐비테이션(캐비테이션의 발단, 슈퍼 캐비테이션, 캐비테이션 손상, 초킹 캐비테이션과 같은)은 밸브의 압력손실계수로부터 예측되었다. 압력손실과 캐비테이션 예측은 밸브의 열림각에 대한 두께 비의 변화에 따라 수행하였다. 예측 데이터는 버터플라이 밸브를 개발하는데 필요한 엔지니어링 데이터로 활용하고자 한다.

• 한국자기학회지
• /
• 제12권6호
• /
• pp.212-217
• /
• 2002

비자성층을 사이에 둔 두 강자성층의 보자력 차이를 이용하여 거대자기저항특성을 나타내는 Ta/CoFe/Cu/NiFe/Ta 구조의 pseudo 스핀밸브를 DC 마그네트론 스퍼터링 방법으로 제조하였다. Ta/CoFe/Cu/NiFe/Ta 구조에서 CoFe층의 두께 변화에 따른 자화 특성 및 자기저항 특성을 조사하였으며, 이 구조에서 CoFe층의 두께가 60 $\AA$일 때 자기저항비는 3.82%이고 CoFe층과 NiFe층 사이의 보자력 차이는 27.4 Oe이다. Ta/CoFe/Cu/NiFe/Ta 구조를 갖는 pseudo 스핀밸브에서 CoFe층과 NiFe층의 보자력 차이는 CoFe층의 두께가 20 $\AA$에서 40 $\AA$까지 증가함에 따라 증가하였으며 40 $\AA$ 이상에서는 감소하였다. 이와 같은 결과는 박막의 결정성 및 포화 자기변형(λ$_{s}$)의 변화에 의한 것으로 판단된다. Cu층과 NiFe층 사이에 CoFe층을 삽입한 Ta/CoFe/Cu/NiFe/Ta 구조에서 삽입층인 CoFe층의 두께 변화에 따른 자화특성 및 자기저항 특성을 조사한 결과 CoFe두께가 10$\AA$시 자기저항비가 6.7 %이며. 삼층막 구조 보다 자기저항비가 약 1.5배 이상 증가함을 알 수 있었다.