• 한국진공학회지
• /
• 제8권3A호
• /
• pp.238-244
• /
• 1999

Pt/SBT/Pt capacitors were fabricated using the MOD-derived $SrBi_{2x}Ta_2O_9$ (SBT) films and their ferroelectic and leakage current characteristics were investigated with post annealing at 400~$800^{\circ}C$. Although the MOD-derived SBT film exhibited the hysteresis loop typical for the leaky film, the well-saturated ferroelectric hysteresis loop could be obtained by post annealing the Pt/SBT/Pt capacitors at $550^{\circ}C$~$800^{\circ}C$. The remanent polarization $2P_r$ of the SBT film exhibited a maximum value of 9.72$\mu\textrm{cm}^2$ with post annealing at $600^{\circ}C$, and then decreased with increasing the post annealing temperature above $600^{\circ}C$. The MOD-derived SBT films exhibited the high leakage current density of ~$10^{-3} \textrm{A/cm}^2$ at 75kV/cm. With post annealing the Pt/SBT/Pt capacitor at 600~$800^{\circ}C$, however, the leakage current density decreased remarkably to less than $10^{-6}\textrm{A/cm}^2$ at 75kV/cm.

• Geomechanics and Engineering
• /
• 제6권4호
• /
• pp.377-389
• /
• 2014

The vacuum consolidation method which was proposed by Kjellman in 1952 has been studied extensively and used successfully since early 1980 throughout the world, especially in East and Southeast Asia. Despite the increased successful use, different opinions still exist, especially in connection to distribution of vacuum with depth and time in vertical drains and in soil during preloading of soft ground. Porewater pressure measurements from actual cases of field vacuum and vacuum-fill preloading as well as laboratory studies have been examined. It is concluded that (a) a vacuum magnitude equal to that in the drainage blanket remains constant with depth and time within the vertical drains, (b) as expected, vacuum does not develop at the same rate within the soil at different depths; however, under ideal conditions vacuum is expected to become constant with depth in soil after the end of primary consolidation, and (c) there exists a possibility of internal leakage in vacuum intensity at some sublayers of a soft clay and silt deposit. A case history of vacuum loading with sufficient subsurface information is analyzed using the ILLICON procedure.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제36회 동계학술대회 초록집
• /
• pp.171.2-171.2
• /
• 2009

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2008년도 제34회 동계학술대회 초록집
• /
• pp.315-315
• /
• 2008

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권5호
• /
• pp.185-190
• /
• 2002

Capacitor material utilized in the downsizing passive devices and dynamic random access memory(DRAM) requires the physical and electrical properties at given area such as capacitor thickness reduction, relative dielectric constant increase, low leakage current and thermal stability. Common capacitor materials, $SiO_2$, $Si_3N_4$, $SiO_2$/$Si_3N_4$,TaN and et al., used until recently have reached their physical limits in their application to several hundred angstrom scale capacitor. $Ta_2O_{5}$ is known to be a good alternative to the existing materials for the capacitor application because of its high dielectric constant (25 ~35), low leakage current and high breakdown strength. Despite the numerous investigations of $Ta_2O_{5}$ material, there have little been established the clear understanding of the annealing effect on capacitance characteristic and conduction mechanism, design and fabrication for $Ta_2O_{5}$ film capacitor. This study presents the structure-property relationship of reactive-sputtered $Ta_2O_{5}$ MIM capacitor structure processed by annealing in a vacuum. X-ray diffraction patterns skewed the existence of amorphous phase in as-deposited condition and the formation of preferentially oriented-$Ta_2O_{5}$ in 670, $700^{\circ}C$ annealing. On 670, $700^{\circ}C$ annealing under the vacuum, the leakage current decrease and the enhanced temperature-capacitance characteristic stability. and the leakage current behavior is stable irrespective of applied electric field. The results states that keeping $Ta_2O_{5}$ annealed at vacuum gives rise to improvement of electrical characteristics in the capacitor by reducing oxygen-vacancy and the broken bond between Ta and O.

• 한국정밀공학회지
• /
• 제26권8호
• /
• pp.112-118
• /
• 2009

A pressure rise is generated while air bearing stages are moving in high vacuum environment. This study analyzed this pressure rise phenomenon theoretically and verified it experimentally using two different kinds of stages - linear and rotary air bearing stages. Results indicate that the pressure rise was caused by additional leakage resulting from stage velocity, along with adsorption and outgassing of gas molecules from the guide rail surface. Though tilting of the stage due to acceleration and deceleration reached several micrometers, it had a negligible effect on pressure rise because the tilting time was very short. Therefore, a rotary air bearing stage showed much less pressure rise than a linear stage because the rotary stage theoretically has nothing to do with the above causes. Additional leakage caused by stage velocity was inevitable if the stage had movements, but pressure rise caused by adsorption and outgassing could be suppressed by improving the surface quality to reduce real surface area, and by coating the guide rail surface with titanium nitride (TiN) which has less adhesion probability of gas molecules. The results also indicate that the pressure rise increased when the air bearing stage operated under high vacuum conditions.

• Applied Science and Convergence Technology
• /
• 제25권1호
• /
• pp.15-18
• /
• 2016

Study investigated the optimal anodizing conditions for fabricating an oxide film that produces less contamination in a corrosive plasma environment, using oxalic acid and tartaric acid. Oxide films were produced using sulfuric acid, oxalic acid, and tartaric acid electrolyte mixtures with various mole ratios. The oxide film made by adding 0.05M tartaric acid to 0.3M oxalic acid showed higher breakdown voltage and lower leakage current. Additionally, contamination particles were reduced during plasma etching, thus demonstrates that this mixture presented optimal conditions. However, higher tartaric acid content (0.1 M, 0.15 M) led to lower breakdown voltages and higher leakage currents. Also, it resulted in more cracking during thermal shock tests as well as the generation of more contamination particles during plasma processing.

• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.57-65
• /
• 2003

본 연구에서는 웨이퍼 레벨 진공 패키징된 MEMS자이로스코프 소자의 신뢰성 시험 및 분석을 통하여 웨이퍼 레벨 진공 패키징의 파괴 메카니즘을 연구하였다. 진공 패키징의 주된 파괴 모드는 누설, 가스투과, 그리고 outgassing이다. 누설은 접합 계면이나 재질의 결함을 통하여 주로 발생되며, 접합폭을 증가시키거나 단결정 실리콘을 사용하면 누설이 감소한다. Outgassing은 실리콘 및 유리기판의 표면 및 내부에서 발생하며 주로 $H_2O$와, $CO_2$, $C_3H_5$ 및 유기 오염물질이었다. Epi-poly의 경우 SOI 웨이퍼보다 약 10배의 outgassing을 발생시킨다. 또한 유리기판을 샌드블라스트 공정을 사용하여 가공한 경우, 약 2.5배의 outgassing 양이 증가한다. Outgassing 제거를 위해서는 접합 전에 웨이퍼를 pre-baking하는 과정이 필수적이며, outgassing의 발생을 최대로 하기 위한 최적의 pre-baking조건은 실리콘과 유리 웨이퍼를 $400^{\circ}C$와 $500^{\circ}C$ 사이에서 pre-baking하는 것이다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1157-1161
• /
• 2011

본 연구에서는 튜브 시스템 내부를 대기압 이하로 감압하여 유지시키는데 필요한 진공 펌프 시스템의 용량에 관한 파라메타들의 영향을 연구하였다. 튜브 열차 시스템은 기존 육상 교통의 속도 한계를 극복하기 위하여 튜브 내부를 대기압 이하로 유지하여 주행하는 열차의 공기 저항을 크게 줄일 수 있다. 진공 펌프 시스템은 튜브 내부를 감압시키고, 튜브 내부로 누설되는 공기를 추가적으로 배출시키는 역할을 한다. 튜브 구조물의 누설을 고려한 정량적 및 정성적 용량을 산정하기 위하여 진공 펌프의 용량에 영향을 끼치는 파라메타를 선정하여 각각의 변화에 대한 영향을 검토하였다. 콘크리트의 압력 누설 실험식을 이용하여 누설량을 구하고, 그 결과를 진공 펌프 용량 산정에 반영하였다. 본 결과는 진공 펌프 구동에 소요되는 동력이 튜브 열차 공기 저항 저감으로 인한 동력비 절감 효과를 비교 분석하는 데에도 참고 자료로 활용될 것이다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.287-290
• /
• 2006

Orbiter mechanism has been applied to vacuum pump design for small oxygen generator where low vacuum of about 200mmHg is required. Performance of the designed vacuum pump has been numerically investigated: calculated volumetric and adiabatic efficiencies were 69.7% and 83.9%, respectively for leakage clearance of $10{\mu}m$. Total efficiency of the orbiter vacuum pump was 77.5%. At the shaft speed of 1700 rpm suction displacement volume of 6.3cc provided discharge flow at the rate of 2.3 liter/min with power consumption of 10.1Watt. Torque variation of the orbiter pump was only about 20% of that of diaphragm pump.