• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.4
• /
• pp.10-16
• /
• 2010

In this paper, synthesis here Mn add to Ar injection the state and a vacuum an atomosphere $ZnGa_2O_4$ : Mn, ZnO and $Ga_2O_3$ power of 1 : 1 mole ratio mixture. Manufacture a close examination of oxygen a component variation luminescence a specific character reach an in fluence of $ZnGa_2O_4$ : Mn, luminescence spectrum observation also an explanation of Mn site symmetry and at luminescence spectrum reach an influence from low temperature photoluminescence spectrum.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.323-328
• /
• 1989

In this paper, we studied the diagnostic method of insulation deterioration for 22.9kV CNCV cable using D.C potential decay component. At first, arbitrary D.C high voltage is appeied the CNCV cable for two minutes and switched off in vacuum. And then D.C potential decay components is measured for ten minutes. It is detecting source for cable insulation deterioration that its gradient is. Provisionally, we decided the criterion voltage and select the high voltage meter and S.W.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.10
• /
• pp.83-90
• /
• 2007

The vehicle dynamic control system needs to detect the yaw rate of vehicle and a yaw rate sensor is required as a central component. Therefore, A sensor on the basic of the "tuning fork method" for automotive controls is being developed. The sensor was fabricated by the surface micro machining process to miniaturize its size. The sensor output offset is ${\pm}0.37^{\circ}/sec$ in the room temperature. The resonance frequency of the fabricated yaw rate sensor is measured to 5.29kHz for the drive mode. Tests of the sensor demonstrate that its performance is equivalent to that required for implementation of a yaw control system. Vehicle handling and safety are substantially improved using the sensor to implement yaw control.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.1-8
• /
• 1996

The component analysis of wax for detecting temperature in automobile thermostat of the automotive engine and manufacture of it with distillation and solvent extraction were progressed. From the lift test results of prepared samples, it was found that the solvent extracted samples were in the proper range for use as an automobile thermostat of the automotive engine. And more accurate wax could be manufactured by high vacuum fractional distillation and acid treatment after solvent extraction from crude oil pitch.

• Applied Biological Chemistry
• /
• v.23 no.2
• /
• pp.106-114
• /
• 1980

The flavor constituents of Korean Milgam were extracted with a nitrogen gas stream under partial vacuum and identified by gas liquid chromatography. By employing the extraction coefficient, it was possible to determine the concentration of components in Milgam as well as in the extracts. Among 53 GLC peaks, 26 components were identified. Ethanol was the most abundant component (140ppm), followed by limonene (120ppm). These two were the most important flavor constituents.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.153-163
• /
• 2017

Transparent conducting electrodes (TCEs) are attracting considerable attention as an important component for emerging optoelectronic applications such as liquid crystal displays, touch panels, and solar cells owing to their attractive combination of low resistivity (<$10^{-3}{\Omega}cm$) and high transparency (>80%) in the visible region. The solution-based process has unique properties of an easy fabrication procedure, scalability, and low cost compared to the conventional vacuum-based process and may prove to be a useful process for fabricating TCEs for future optoelectronic applications demanding large scale and flexibility. In this paper, we focus on the introduction of a solution-based process for TCEs. In addition, we consider the powder materials used to fabricate solution-based TCEs and strategies to improve their transparent conducting properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.336-339
• /
• 2007

The enhanced control of OLED deposition processes by Organic Vapor Phase Deposition $(OVPD^{(R)})$ is discussed. $OVPD^{(R)}$ opens a wide space of process control parameters. It allows the accurate and individual control of deposition layer properties like morphology and precise mixing of multi component layers (co-deposition) in comparison to conventional deposition manufacturing processes like e. g. VTE (vacuum thermal evaporation).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.605-608
• /
• 1999

We report investigations on a Pentacene thin film as a component for active layer of Organic thin film transistors. Pentacene film was deposited by Organic Molecular Beam Deposition(OMBD) and Al electrode was deposoted by vacuum evaporation. Electrical characterization of Pentacene films were measured by the three-terminal contact resistance methods, as the results contact resistance between pentacene films and the Aluminium electrode is 5.064G$\Omega$. The Al contact with the pentacene shows the bottom contact resistance. From the current-voltage characteristics, electrical conductivity of the Pentacene film is found as ~ 10$^{-4}$ /cm. physical characterization of pentacene films were measured by UV-spectrum and Cyclic-Voltammetry method.

• Journal of Welding and Joining
• /
• v.29 no.6
• /
• pp.45-48
• /
• 2011

In this research, laser welding of automotive transmission components was investigated to replace electron beam welding which is normally conducted under vacuum condition. Fiber laser welding was applied to the automotive transmission components - hub clutch and annulus gear. In the component welding, the laser welding parameters were optimized to eliminate spatters and the end crater. By applying laser welding to the transmission parts, the process time could be reduced up to 70% compared with the current electron beam welding process.

• Land and Housing Review
• /
• v.10 no.3
• /
• pp.23-32
• /
• 2019

Vacuum Insulation Panel(VIP) has the lowest thermal conductivity among present insulations. It is composed of envelope, core material and getter. Aluminum film is usually used as the envelope of VIP, and it is important component to decide the useful life of VIP. In this research, the thermophysical properties of incombustible fiber glass core VIP were investigated with the possibility of its architectural applications. The results of this research can be summarized as follows: 1) The thermal conductivity of 20mm-thick fiber glass core VIP is resulted as 0.00177W/m·K, which means that 20mm-thick VIP can meet all the reinforced insulation guideline and it can be used in any envelope of any region in Korea. 2) As a result of the test of incombustion and gas toxicity, fiber glass core VIP was suitable for incombustible material. 3) As the test result for the long term thermal conductivity, fiber glass core VIP was found out that it would keep above 10 times insulating performance than polystyrene foam and glass fiber. 4) To meet the thermal transmittance of 0.12W/㎡K, limited-combustible insulation of expanded polystyrene foam and phenolic foam should be used respectively as thick as above 280mm and 170mm, incombustible VIP can meet the same insulation level with 20mm thickness. 5) The price competitiveness of incombustible VIP to meet the thermal transmittance of 0.12W/㎡·K was about 1,500won/㎡ higher than that of phenolic foam.