• Journal of Sensor Science and Technology
• /
• v.10 no.5
• /
• pp.292-303
• /
• 2001

This work reports the tunneling effects of the lateral field emitters. Tunneling effect is applicable to the VMFS(vacuum magnetic field sensors). VMFS uses the fact that the trajectory of the emitted electrons are curved by the magnetic field due to Lorentz force. Polysilicon was used as field emitters and anode materials. Thickness of the emitter and the anode were $2\;{\mu}m$, respectively. PSG(phospho-silicate-glass) was used as a sacrificial layer and it was etched by HF at a releasing step. Cantilevers were doped with $POCl_3(10^{20}cm^{-3})$. $2{\mu}m$-thick cantilevers were fabricated onto PSG($2{\mu}m$-thick). Sublimation drying method was used at releasing step to avoid stiction. Then, device was vacuum sealed. Device was fixed to a sodalime-glass #1 with silver paste and it was wire bonded. Glass #1 has a predefined hole and a sputtered silicon-film at backside. The front-side of the device was sealed with sodalime-glass #2 using the glass frit. After getter insertion via the hole, backside of the glass #1 was bonded electrostatically with the sodalime-glass #3 at $10^{-6}\;torr$. After sealing, getter was activated. Sealing was successful to operate the tunneling device. The packaged VMFS showed very small reduced emission current compared with the chamber test prior to sealing. The emission currents were changed when the magnetic field was induced. The sensitivity of the device was about 3%/T at about 1 Tesla magnetic field.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.6
• /
• pp.309-314
• /
• 2010

The numerical study for the effect of various factors that affect the temperature distribution of the process glass installed above the large rectangular heater plate was carried out. For the calculation, heat flux, distance between heat source and process glass plate, effect of vacuum condition and convection in a chamber were considered as important factors. The results showed that the temperature gradient on the glass was increased at the natural convection because of the buoyancy force increases due to the heated air. Also, the more heat flux and distance between the heater plate and glass increases, the more increasing the temperature gradient was. In the case of isothermal heating wall, the temperature variation was smaller than the uniform heat flux condition.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.133-137
• /
• 2016

The surface treatment of cover glass for conversion efficiency of photovoltaic cell is important to reduce reflectivity and to increase the incident light. In this work, random textured anti glare (RTAG) glass was prepared by wet surface coating method. Optical properties due to the changes of surface morphology of RTAG glass were compared and conversion efficiency of photovoltaic cell was researched. Grain size and changes of surface morphologies formed with surface etching time greatly affected optical transmittance and transmission haze. Current density (Jsc) were high at the condition when surface morphologies reflection haze were low and transmission haze were high. Jsc was $40.0mA/cm^2$ at glancing angle of $90^{\circ}$. Incidence light source was strongly influenced by surface treatment of cover glass at high incidence angle but was hardly affected light source at the low angle of incidence.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.582-587
• /
• 2012

Recently, the low-emissivity glass has been used to reduce the energy loss through building windows. However, it simply reduces the inflow of solar rays and has a relatively high heat transmission coefficient. To solve the problems, a high-efficiency vacuum glazing has been under development but it has not been actively used due to its high price and insufficient performance. In this paper, the effects of internal pressure, pillar (spacer) height, pillar diameter, pillar interval, emissivity etc. on the performance of vacuum glazing have been analyzed with three-dimensional computational fluid dynamics and structural analysis. As a result, the performance of vacuum glazing was predicted more accurately and major factors that determine the performance of vacuum glazing were optimized.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1421-1423
• /
• 1996

In this study, the effect of solar cell cover glass on the solar cell performance is evaluated. Silicon solar cell (active area:4*6cm, efficiency:12.6% at AMO condition) is used for this study. ITO(Indium tin Oxide) film thickness of the ITO/AR/substrate glass/solar cell structure samples are $40{\AA}$, $60{\AA}$, $160{\AA}$, $240{\AA}$ respectively. The solar cell maximum output power on the stacking structure variations showed 465mW in the AR/ITO/substrate glass/solar cell, and minimum output power showed 403mW in the AR/substrate glass/solar cell. The maximum output power of the solar cell on the ITO thickness variations of the ITO/AR/substrate glass/solar cell showed 460mW at $40{\AA}$ then decrease output power as ITO thickness increase. For environment tests, all samples are exposed UV light in the vacuum chanber. The output power degradation of AR(UVR)/substrate glass/solar cell stacking structure is small compared with ITO/AR(UVR)/substrate glass/solar cell stacking structure.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.700-706
• /
• 2016

Etch rate, surface roughness and microstructure as plasma resistance were evaluated for six kinds of oxide glass with different compositions. Borosilicate glass (BS) was found to be etched at the highest etch rate and zinc aluminum phosphate glass (ZAP) showed a relatively lower etch rate than borosilicate. On the other hand, the etching rate of calcium aluminosilicate glass (CAS) was measured to be similar to that of sintered alumina while yttrium aluminosilicate glass (YAS) showed the lowest etch rate. Such different etch rates by mixture plasma as a function of glass compositions was dependent on whether or not fluoride compounds were formed on glass and sublimated in high vacuum. Especially, in view that $CaF_2$ and $YF_3$ with high sublimation points were formed on the surface of CAS and YAS glasses, both CAS and YAS glasses were considered to be a good candidate for protective coating materials on the damaged polycrystalline ceramics parts in semi-conductor and display processes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.123-123
• /
• 2015

Al doped ZnO(AZO) films as a transparent conductive oxide (TCO) electrode were deposited on glass, polyethylene naphthalate (PEN) and polyethylene terephthalate (PET) at room temperature by a conventional rf-magneton sputtering (CMS) and a facing target sputtering (FTS) using Al2O3 and ZnO targets. In order to investigation of AZO properties, the structural, surface morphology, electrical, and optical characteristics of AZO films were respectively analyzed. The resistivities of AZO films using FTS system were $6.50{\times}10-4{\Omega}{\cdot}cm$ on glass, $7.0{\times}10-4{\Omega}{\cdot}cm$ on PEN, and $7.4{\times}10-4{\Omega}{\cdot}cm$ on PET substrates, while the values of AZO films using CMS system were $7.6{\times}10-4{\Omega}{\cdot}cm$ on glass, $1.20{\times}10-3{\Omega}{\cdot}cm$ on PEN, and $1.58{\times}10-3{\Omega}{\cdot}cm$ on PET substrates. The AZO-films deposited by FTS system showed uniform surface compared to those of the films by CMS system. We thought that the films deposited by FTS system had low stress due to bombardment of high energetic particles during CMS process, resulted in enhanced electrical conductivity and crystalline quality by highly c-axis preferred orientation and closely packed nano-crystalline of AZO films using FTS system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.53-56
• /
• 1998

Electroluminescent(EL) devices based on organic materials have been of great interest due to their possible applications for large-area flat-panel displays, where they are attractive because of their capability of multicolor emission, and low operation voltage. In this study, glass substrate/ITO/Eu(TTA)$_3$(Phen)/Al(A), glass substrate/ITO/TPD/Eu(TTA)$_3$(p-hen)/Al(B) and glass substrate/ITO/TPD/Eu(TTA)$_3$(phen)/AlQ$_3$/Al(C) structures were fabricated by vacuum evaporation method. where aromatic diamine(TPD) was used as a hole transporting material, Eu(TTA)$_3$(phen) as an emitting material. and tris(8-hydroxyquinoline)Aluminum(AlQ$_3$) as an electron transporting layer. Electroluminescent(EL) and I-V characteristics of Eu(TTA)$_3$(Phen) with a various thickness were investigated. This structure shows the red EL spectrum, which is almost the same as the PL spectrum of Eu(TTA)$_3$(phen). I-V characteristics of this structure show that turn-on voltage was 9V and current density was 0.01A/$\textrm{cm}^2$ at a dc operation voltage of 9V. Electrical transporting phenomena of these structures was explained using the trapped- charge-limited current model with I-V characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.203-203
• /
• 2010

Nano-crystalline Si thin films were deposited on polymer and glass by inductively coupled plasma (ICP) - assisted RF magnetron sputtering at low temperature in an argon and hydrogen atmosphere. Internal ICP coil was installed to increase hydrogen atoms dissociated by the induced magnetic field near the inlet of the working gases. The microstructure of deposited films was investigated with XRD, Raman spectroscopy and TEM. The crystalline volume fraction of the deposited films on polymer was about 70% at magnetron RF power of 600W and ICP RF power of 500W. Crystalline volume fraction was decreased slightly with increasing magnetron RF power due to thermal damage by ion bombardment. The diffraction peak consists of two peaks at $28.18^{\circ}$ and $47.10^{\circ}\;2{\theta}$ at magnetron RF power of 600W and ICP RF power of 500W, which correspond to the (111), (220) planes of crystalline Si, respectively. As magnetron power increase, (220) peak disappeared and a dominant diffraction plane was (111). In case of deposited films on glass, the diffraction peak consists of three peaks, which correspond to the (111), (220) and (311). As the substrate temperature increase, dominant diffraction plane was (220) and the thickness of incubation (amorphous) layer was decreased.

• Journal of the Korean Vacuum Society
• /
• v.14 no.3
• /
• pp.159-164
• /
• 2005

Indium tin oxide (ITO) films were deposited on a glass slide at a thickness of 280 nm by radio frequency(rf) magnetron sputtering from a ceramic target composed of $In_2O_3\;(90\%)\;+\;SnO_2\;(10\%)$. We investigated the effects of the annealing temperature (Ta) between 200 and 350'E for 30 min in air on such properties as thermal stability, surface morphology, and crystal structure of the films. X-ray diffraction spectra revealed that all the films were oriented preferably with [222] direction and [440] direction and the peak intensity increased with increasing annealing temperature. X-ray photoelectron spectroscopy (XPS) showed that the sodium was out-diffused from the glass substrate at the annealing temperature of $350^{\circ}C$. The sodium composition of the ITO film amlealed at $350^{\circ}C\;for\;30\;min\;was\;2.5\%$ at the surface. Also the sodium peak almost disappeared after 3 keV $Ar^+$sputtering for 6 min. The visible transmittance of all ITO films was over $77\%$.