• The Journal of Korean Society of Virology
• /
• v.26 no.2
• /
• pp.245-249
• /
• 1996

Hantaan virus vaccine was developed in 1988 and proved effective. This vaccine is a kind of inactivated vaccine, stable for two years when stored at $2-8^{\circ}C$. Almost virus vaccines including Hantaan virus vaccine are produced and kept in fluid state, and the immumogenicity can be easily destroyed at room temperature or at higher temperature. Therefore the vaccines should be kept in the refrigerator to maintain the immunogenicity. In this study, glucose and/or lactose was added as a stabilizer into Hantaan virus vaccine to increase the stability and dried in vaccum with ethanol treatment. 5% glucose and or lactose in Hantaan virus vaccine most effectively increased the stability of vaccine and maintained the immunogenicity at least for three months at room temperature. But drying with ethanol treatment did not help increasing the stability. These results suggest that glucose and lactose could be good stabilizer of virus vaccines.

• Journal of the Korean Ceramic Society
• /
• v.37 no.5
• /
• pp.444-452
• /
• 2000

Dense composites of titanium matrix and Al2O3 matrix with reinforcements of carbon or titanium carbide fibers were successfully fabricated by high-pressure self-combustion sintering method or combustion reacton under 30 MPa of uniaxial pressure with an aid of external heating in vaccum. It was found that the fibers were uniformly distributed in the matrix, and aligned in a phase perpendicular to the pressure axis. As a moel ratio of Ti/C or reaction time increased, the density of Ti-matrix composite increased Micro pores around fibers could be removed by using clean carbon fibers without sizing agent on their surface. The evolution of carbide fibers from carbon fibers was observed. The composition of the various phases around fibers were analyzed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.194-200
• /
• 2000

The sealing performance of an elastomeric O-ring seal using NBR and FFKM has been analyzed for the contact stress behaviors that develop between the O-ring seal and the surfaces with which it comes into contact. The leakage of an O-ring seal will occur when the pressure differential across the seal just exceeds the initial (or static) peak contact stress. The contact stress behaviors that develop in compressed O-rings, in common case of restrained geometry(grooved), are investigated using the finite element method. The analysis includes material hyperelasticity and axisymmetry. The computed FEM results show that the contact stress behaviors are related to materials of NBR and FFKM and temperature of vaccum chamber.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1520-1523
• /
• 1997

A rigorous dynamic simulation was performed in binary gas mixture H$_{2}$/CO (70:30 vol.%) to determinate start-up operating conditions of PSA(Pressure Swing Adsorption) processes. The rigorous dynamic model for the PSA process contains an Ergun equation for expressing the pressure drop in a bed, and valve equations to compute the boundary pressure change of the bed. As the result of the continuous dynamic simulation of 100 operating cyles in various initial conditions, the unsteady-state appeared in the early period and the cyclic steady-state came out about 20th cycle in feed condition and vaccum condition, and 30th cycle in pure H$_{2}$ condition. As time goes by valve equations made change the pressure at each end of the bed in ressurization, countercurrunt-depressurization and pressure equalization steps. The H$_{2}$ purity and the recovery is 99.99% and 86.73% respectively, which is slightly higher than the experimental data. Main contributiion of this study includes supplying fundamental technologies of handling combined variables PSA processes by developing rigorous models.

• Journal of the Korean Ceramic Society
• /
• v.22 no.6
• /
• pp.87-93
• /
• 1985

The hematite the magetite and the maghemite thin film were prepared by oxidation and reductino of the vaccum-evaporated iron thin film. Interre;atoms between film preparation process and the electrical properties were investigated. At room temperature the electrical conductivity of the iron the hematite the magnetite and the maghemite thin film were $1{\times}10^4\Omega^{-1}cm^{-1}$, 2{\times}10^{-5}\Omega^{-1}cm^{-1}$, $3{\times}10^{-5}\Omega^{-1}cm^{-1}$, and $4{\times}10^{-5}\Omega^{-1}cm^{-1}$, resp-ectively. The surface of each thin film was dense and homogeneous. At the temperature that the iron thin film was converted into the hematite thin film the electrical conductivity decreased rapidly and the electrical con-ductivity of the hematite thin film increased as temperature increased. The hematite thin film was reduced to the magnetite thin film in H2 atmosphere. The electrical conductivity decreased rapidly at the temperature that the maghemite thin film is formed by oxidation of the magnetite thin film and the electrical conductivity of the maghemite thin film increased as temperature increased.

• Journal of the Korean Ceramic Society
• /
• v.28 no.6
• /
• pp.437-442
• /
• 1991

Temperature and atmosphere dependence of electrical conduction of the metal Cu, Ag, Au films, vaccum evaporated on glass, was investigated. The structural changes of the metal films were examined by SEM and high temperature XRD. The electrical resistance slightly increased with initial temperature increase up to the inflection point and decreased to minimum value, after this rapidly increased with further temperature increased below minimum. These phenomena were caused by the thermally induced film failure as a result of the mass transport. The temperature for the film failure increased in the order of O2, Air, Vacuum, N2, Ar in Cu, Ag films and Air, Vacuum, N2, Ar in Au film. The increase of resistance at the lower temperature range was attributed to the lattice distortion by disordered crystal structure, while the decreasing resistance was attributed to the removal of structural defects and film densification.

• KSBB Journal
• /
• v.14 no.5
• /
• pp.561-565
• /
• 1999

Optimum conditions for vacuum-drying ad cultivation of yeast cells for the production of active dry yeast were examined. At lower temperature, more drying time was required to dry the yeast pellet to reach the desirable water content(8%). Optimum temperature of vaccum oven and time for drying was 63$^{\circ}C$ and 90 min, respectively. Optimum medium composition for flask culture using cane molasses as the substrate were 0.25% sugar, 0.013% $K_2$HPO$_4$, 0.1% $K_2$HPO$_4$. and 0.125% (NH$_4$)$_2$SO$_4$. Culture temperature $25^{\circ}C$ gave the highest survival rate of dired yeast. After finishing fed-batch culture and the culture was left in the fermentor without adding any sugar or nutrient, survival of the dried yeast harvested from the fermentor increased to 86.0% after 36 hr. It was also observed that the yeast cells with higher budding rates showed lower survival rate.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.18-21
• /
• 2000

A nonconstact technique for reducing the core loss of a grain oriented silicon steel has been developed by the use of mechanical scribing Q-switched laser plasma jet or electron beam irradiation. Among these methods electron beam irradiation has advantages of domain refining without any deformation or damage of insulating film on the surface of a grain criented Si-Fe. Over the past years this processing was performed in vaccum of 10-4 Torr or below causing the problem of high cost and difficulty of continuous works. In this paper a miniature electron permeable window through which electron beam energy 4-80keV and average current 0.1-2mA. were obtained for electron beam irradiating on air was designed and manufactured.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.181-189
• /
• 1992

The purpose of this investigation is to examine the effects of the strengthening treatments on the mechanical properties of the flame-sprayed titania ceramic coating layer. The strengthening treatments for flame sprayed specimens were carried out in 12 different conditions in vaccum furance. The mechanical properties such as microhardness, thermal shock resistance, adhesive strength and erosion resistance were tested for the sprayed specimens after strengthening treatments. And it was clear that the mechanical properties of coating layer were much improved by the strengthening treatments. The results obtained are summarized as follows; 1. It was shown that the metallurgical bond was formed between substrate and coating layer by the strengthening treatments and that thermal shock resistance and adhesive strength were remarkably raised. 2. Microhardness of coating lay was considerably increased by the strengthening treatments. 3. Erosion resistance and porosity of coating layer were slightly improved by the strengthening treatments.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.65-71
• /
• 1996

A novel lateral field emitter triode has been designed and fabricated. It has self-vacuum environmets and low turn-on voltage, so that the chief problems of previous field emission devices such as additional vacuum sealing process and high turn-on voltage are settled. An in-situ vaccum encapsulation empolying recessed cavities by isotropic RIE (reactive ion etch) method and an electron beam evaporated molybdenum vacuum seals are implemented to fabricate the new field emitter triode. The device exhibits low turn-on voltage of 7V, stabel current density of 2.mu.A/tip at V$_{AC}$ = 30V, and high transconductance (g$_{m}$) of 1.7$\mu$S at V$_{AC}$ = 22V. The superb device characteristics are probably due to sub-micron dimension device structure and the pencil type lateral cathode tip employing upper and lower LOCOS oxidation.