• Progress in Medical Physics
• /
• v.5 no.1
• /
• pp.25-39
• /
• 1994

To measure the velocity of heart wall and local flow transctaneously in blood vessels, we have developed a single channel 3.1 MHz pulsed ultrasonic Doppler velocity meter. Ultrasound pluse width and repetition frequency (PRF) used in the velocity meter is 1 ${\mu}$sec 6kHz reapectively, and the Doppler shift of the backscattered echo signal is sensed in a phase detector by coherent demodulation method. From the output of the phase detector, the Doppler signal corresponding to the mean velocity of acoustic wave scatterers over a small region is obtained by using a range gate, sample holder and band-pass filter. Mean frequency of Doppler signal is estimated by zero-crossing counter and the instantaneous velocity of scatters is displayed as a function of time. It is possible to estimate velocity profile, volume flow and flow acceleration of vessels in man if the number of channels and range resolution in increased.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.3
• /
• pp.77-83
• /
• 2006

The purpose of this study is to analyze lateral displacement behavior of clay layers in case of the banking in soft ground through model tests. Seven model tests varying with thickness of soft clay and loading velocity are performed to correlate between ground heaving and loading velocity. In case of low loading velocity, vertical settlement below loading plate and small ground heaving are obviously observed. In case of the high loading velocity, it is shown that both soil displacement at the end of a loading plate and surface heaving are large. In addition, the calculated displacements show good agreement with three cases of field measurements in clay with high moisture contents so that we can predict the range of heaving area and the amount of heaving.

• Physical Therapy Korea
• /
• v.13 no.2
• /
• pp.1-8
• /
• 2006

The main purposes of this study were to find the correlation between walking ability assessment tools using the Modified Barthel Index (MBI), Functional Independence Measure (FIM), Spinal Cord Injury Measurement II (SCIM II), Walking Index for Spinal Cord Injury (WISCI), walking velocity, and walking endurance. The study population consisted of 56 patients with spinal cord injury referred to the department of Rehabilitative Medicine in the National Rehabilitation Hospital. All subjects were ambulatory with or without an assistive device. All participants were assessed by MBI, FIM, SCIM II, WISCI, walking velocity, and walking endurance. The data were analyzed using Pearson correlation analysis and X2. There was significant correlation between the MBI, FIM, SCIM II, WISCI, walking velocity, and walking endurance (p<.01). In particular, WISCI has a significant correlation with SCIM II(p<.001). Therefore the WISCI scale is an appropriate assessment tool to predict the gait ability of patients with spinal cord injury. Further study about MBI, FIM, SCIM II, WISCI, walking velocity, and walking endurance is needed using a longitudinal study design.

• Journal of computational fluids engineering
• /
• v.13 no.1
• /
• pp.21-27
• /
• 2008

A numerical study for laminar flow in the entrance region of helical tubes for uniform inlet velocity conditions is carried out by means of the finite volume method to investigate the effects of Reynolds number, pitch and curvature ratio on the flow development. This results cover a curvature ratio range of 1/10$\sim$1/320, a pitch range of 0.0$\sim$3.2, and a Reynolds number range of 125$\sim$2000. It has been found that the curvature ratio does significantly effect on the angle of flow development, but the pitch and Reynolds number do not. The characteristic angle $\phi_c(=\phi/\sqrt{\delta})$, or the non-dimensional length $\overline{l}(=l\sqrt{\delta}cos(atan\lambda)/d)$ can be used to represent the flow development for uniform inlet velocity conditions. In uniform inlet velocity conditions, the growth of boundary layer delays the flow development attributed to centrifugal force, and in which conditions the amplitude of flow oscillations is smaller than that in parabolic inlet velocity conditions. If the pitch increases or if the curvature ratio or Reynolds number decreases, the minimum friction factor and the fully developed average friction factor normalized with the friction factor of a straight tube and the flow oscillations decrease.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.496-505
• /
• 2000

A semi-infinite parallel crack propagated with constant velocity in two bonded anisotropic strip under anti-plane clamped displacement is analyzed. Using Fourier integral transform a Wiener-Hopf equation is derived. By solving this equation the asymptotic stress and displacement fields near the crack tip are determined, where the results give the more general expression applicable to the extent of the anisotropic material having one plane of elastic symmetry for the parallel crack. The dynamic stress intensity factor and energy release rate are also obtained as a closed form, which are the results applicable to the problem both of dynamic and static crack under the same geometry as this study. The stress intensity factor approaches zero at the critical crack velocity which is less than the shear wave velocity, but in typical case of isotropic or orthotropic material agrees with the velocity of shear wave. Also a circular shear stress around crack tip is considered, from which the stress is shown to be approximately symmetric about the horizontal axis. Referring to the maximum stress criteria, it could be shown that a brenched crack is formed by crack growth as crack velocity increases.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3
• /
• pp.447-451
• /
• 2013

In this study, a shock absorber whose orifice area changes according to the oil pressure inside the absorber is developed. The orifice widens and narrows when the oil pressure is high and low, respectively; thus, the orifice area changes according to the oil pressure, in other words, according to the extension/compression velocity. It is well known that the damping force can be expressed as $C{\cdot}v^{\alpha}$. For fluid film damping, the force is proportional to velocity, i.e., ${\alpha}=1$, and for orifice damping, it is proportional to the square of velocity, i.e., ${\alpha}=2$. The shock absorber proposed in this paper can exhibit different relationships between the damping force and velocity because the orifice area changes according to the induced oil pressure. The motivation of this study is to develop a method for designing a shock absorber with desired values of C and ${\alpha}$ which is not just 1 or 2. Theoretical and experimental studies have been conducted to verify the damping characteristics of the shock absorber. The effect of some major design parameters on damping characteristics has been also examined to relate the design parameters to the damping characteristics.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.135-144
• /
• 2001

In this study, the time varying boundary control using the right boundary transverse motion is suggested to stabilize the transverse vibration of an axially moving string on the basis of the energy flux between the moving string and the boundaries. The effectiveness of the active velocity boundary control is showed through the FDM simulation results. Sliding mode control is adopted in order to achieve velocity tracking control of the time varying right boundary to dissipate vibration energy of the string effectively. Optical sensor system for measuring the transverse vibration of an axially moving string is developed, and the angle of the incident wave to the right boundary, which is the input of the velocity boundary controller, is obtained. Experimental research is carried out to examine the validity and the performance of the transverse vibration control using the suggested velocity right boundary control scheme.

• Biomedical Science Letters
• /
• v.11 no.4
• /
• pp.435-439
• /
• 2005

To determine the appropriate concentration of papaverine hydrochloride(PPV) for therapeutic intraarterial infusion against cerebral vasospasm and to measure the mean blood flow velocity of the middle cerebral artery in rabbits. Vasospasm was induced in the experimental groups (3 days after infusion; group 1, n=3, 7 days after infusion; group 2, n=3) and a control group (n=l) by placing a blood clot in the subarachnoid space around the top of the internal carotid siphon. PPV (5 mg/kg) was infused into the internal carotid artery. The vascular diameters of the internal carotid artery (ICA) and middle cerebral artery (MCA) were measured on angiograms before and after infusion. The mean blood flow velocity in the MCA was measured on transcranial doppler sonograms before and 24 hours after infusion. After fixation, the MCA was dissected out, stained, and examined microscopically. After PPV infusion in both groups, vascular dilatation of about $20\%$ was seen. The mean increase in blood flow velocity in the group $1(30\%)$ was smaller than in the group $2(70\%)$. The mean blood flow velocity in the MCA decreased by about $30\%$ in both groups, but increased again after 24 hours nearly to the level before PPV infusion. PPV infusion may be more effective in early stages of vasospasm when vascular walls have fewer histologic changes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1183-1190
• /
• 2002

An experimental study is performed to investigate the characteristics of near wake behind a circular cylinder with serrated fins using the constant temperature anemometer and through flow visualization. Previous report(Boo et al., 2001) shows that there are three different modes in vortex shedding behavior. This paper is focused on the identification of the physical reasons why the difference iss occured in vortex shedding. The through flow velocity crossing fins decreases as increasing fin height and decreasing fin pitch mainly due to the flow resistence. Vortex shedding is affected strongly by velocity distribution around fin tube, especially by the velocity gradient. The velocity distribution at X/d=0.0 has lower gradient with increasing freestream velocity and fin height and decreasing fin pitch. Those differences in velocity gradients generate different vortex shedding mechanism.

• The Journal of Korean Physical Therapy
• /
• v.22 no.5
• /
• pp.49-56
• /
• 2010

Purpose: The aim of this study was to evaluate a possible role for cranial artery velocity in cervicogenic headache. Methods: We studied 13 patients with cervicogenic headaches (M=9, F=4, age=$24.50{\pm}3.50\;y$) these were compared to 20 normal subjects (M=10, F=10, age=$23.30{\pm}2.90\;y$). Cervicogenic headache patients were divided into two groups (a myofascial relaxation group, a placebo group). Pain levels were measured using a visual analog scale (VAS). Transcranial Doppler (TCD) ultrasound recordings were used to measure blood flow velocity in the cranial artery. Results: Cervicogenic headache patients exhibited a significantly lower blood flow velocity in the middle cerebral artery. The patients who received an intervention had a significantly higher blood flow velocity in the left middle cerebral artery, right vertebral artery and basilar artery. Compared to the placebo group, the myofascial relaxation group exhibited a significantly decreased level of pain. Conclusion: Cervicogenic headache is pain referred to the head from a source in the cervical spine. Manual therapy affect to cervical spine and soft tissue as well as the passage of these vessels and nerves to recover because it is thought to be able to help.