• Journal of the Korean Electrochemical Society
• /
• v.8 no.2
• /
• pp.88-93
• /
• 2005

Anode-supported solid oxide fuel cell (SOFC) was investigated to increase the cell power density at intermediate temperature through control of the cathode structure. The anode-supported SOFC cell were fabricated by wet process, in which the electrolyte of $8mol\%\;Y_2O_3-stabilized\;ZrO_2 (YSZ)$ was coated on the surface of anode support of Ni/YSA and then the cathode was coated. The cathode has two- or three- layered structure composed of $(La_{0.85}Sr_{0.15})_{0.9}MnO_{3-x}(LSM),\;LSM/YS$ composite (LY), and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3{LSCF)$ with different thickness. Their single cells with different cathode structures were characterized by measuring the cell performance and ac impedance in the temperature range of 600 to $800^{\circ}C$ in humidified hydrogen with $3\%$ water and air. The cell with $LY\;9{\mu}m/LSM\;9{\mu}m/LSCF\;17{\mu}m$ showed best performance of $590mW/cm^2$, which was attributed to low polarization resistance due to LY and to low interfacial resistance due to LSCF.

• Journal of Yeungnam Medical Science
• /
• v.6 no.1
• /
• pp.121-131
• /
• 1989

The temperature-corrected values of blood gas analysis were compared to uncorrected values in 40 cases of open heart surgery under moderate hypothermic cardiopulmonary bypass. The results were as follows. 1. The corrected value of pH was significantly higher than uncorrected value, and it's relationship was ${\Delta}pH=-0.015$ ${\Delta}Temp+0.005$(r=0.81, P<(0.01). 2. The corrected value of $PCO_2$ was lower than uncorrected value, and it's relationship was ${\Delta}PCO_2=1.11$ ${\Delta}Temp+1.81$(r=0.50, P<0.01). 3. The corrected value of $PO_2$ was lower than uncorrected value, and it' s relationship was ${\Delta}PO_2=5.21$ ${\Delta}Temp-1.45$(r=0.32, P<0.01). But there was no clinical significance. 4. The corrected values of $HCO_{3^-}$, base excess, $CO_2$ content and oxygen saturation were similar with uncorrected values. In summery, the values of pH and $PCO_2$were significantly changed by temperature-correction. Because of the neutral point of water (pH=pOH) rises as temperature falls and it change in parallel with the changes in blood pH, a corrected pH of 7.4, $PaCO_2$ of 40mmHg during deep hypothermia would reflect a profound respiratory acidosis. Therefore, the use of the uncorrected value at $37^{\circ}C$ is more preferable and valid means of assessing acid-base management regardless of actual patient temperature.

• Bulletin of the Korean Chemical Society
• /
• v.14 no.4
• /
• pp.439-444
• /
• 1993

The aerobic oxidation of the Fe(II) complex of 1,4,8,11-tetraazacyclotetradecane, [Fe(cyclam)$(CH_3CN)_2](ClO_4)_2$, in MeCN in the presence of a few drops of $HClO_4$ leads to low spin Fe(III) species [Fe(cyclam)$(CH_3CN)_2](ClO_4)_3$. The Fe(III) cyclam complex is further oxidized in the air in the presence of a trace of water to produce the deep green binuclear bismacrocyclic Fe(II) complex $[Fe_2(C_{20}H_{36}N_8)(CH_3CN)_4](ClO_4)_4{\cdot}2CH_3CN$. The Fe(II) ions of the complex are six-coordinated and the bismacrocyclic ligand is extensively unsaturated. $[Fe_2(C_{20}H_{36}N_8)(CH_3CN)_4](ClO_4)_4{\cdot}2CH_3CN$ crystallizes in the monoclinic space group $P2_1/n$ with a= 13.099 (1) ${\AA}$, b= 10.930 (1) ${\AA}$, c= 17.859 (1) ${\AA}$, ${\beta}$= 95.315 $(7)^{\circ}$, and Z= 2. The structure was solved by heavy atom methods and refined anisotropically to R values of R= 0.0633 and $R_w$= 0.0702 for 1819 observed reflections with F > $4{\sigma}$ (F) measured with Mo K${\alpha}$ radiation on a CAD-4 diffractometer. The two macrocyclic units are coupled through the bridgehead carbons of ${\beta}$-diimitie moieties by a double bond. The double bonds in each macrocycle unit are localized. The average bond distances of $Fe(II)-N_{imine}$, $Fe(II)-N_{amine}$, and $Fe(II)-N_{MeCN}$ are 1.890 (5), 2.001 (5), and 1.925 (6) ${\AA}$, respectively. The complex is diamagnetic, containing two low spin Fe(II) ions in the molecule. The complex shows extremely intense charge transfer band in the near infrared at 868 nm with ${\varepsilon}$= 25,000 $M^{-1}cm^{-1}$. The complex shows a one-electron oxidation wave at +0.83 volts and two one-electron reduction waves at -0.43 and-0.72 volts vs. Ag/AgCl reference electrode. The complex reacts with carbon monoxide in $MeNO_2$ to form carbonyl adducts, whose $v_{CO}$ value (2010 $cm^{-1}$) indicates the ${\pi}$-accepting property of the present bismacrocyclic ligand.

• Ceramist
• /
• v.21 no.4
• /
• pp.378-387
• /
• 2018

The optimal fabrication conditions for $Gd_{0.1}Ce_{0.9}O_{2-{\delta}}$(GDC) buffer layer and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-{\delta}}$ (LSCF) cathode on 1mol% $CeO_2-10mol%\;Sc_2O_3$ stabilized $ZrO_2$ (CeScSZ) electrolyte were investigated for application of IT-SOFCs. GDC buffer layer was used in order to prevent undesired chemical reactions between LSCF and CeScSZ. These experiments were carried out with $5{\times}5cm^2$ anode supported unit cells to investigate the tendencies of electrochemical performance, Microstructure development and interface reaction between LSCF/GDC/CeScSZ along with the variations of GDC buffer layer thickness, sintering temperatures of GDC and LSCF were checked, respectively. Electrochemical performance was analyzed by DC current-voltage measurement and AC impedance spectroscopy. Microstructure and interface reaction were investigated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Although the interfacial reaction between these materials could not be perfectly inhibited, We found that the cell, in which $6{\mu}m$ GDC interlayer sintered at $1200^{\circ}C$ and LSCF sintered at $1000^{\circ}C$ were applied, showed good interfacial adhesions and effective suppression of Sr, thereby resulting in fairly good performance with power density of $0.71W/cm^2$ at $800^{\circ}C$ and 0.7V.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.493-498
• /
• 1998

CdTe films were deposited by close spaced sublimation with various substrate temperatures, cell areas, and thicknesses of CdTe and ITO layers and their effects on the CdS/CdTe solar cells were investigated. The resistivity of CdTe layers employed in this study was 3$\times$ $10^{4}$$\Omega$cm For constant substrate temperature the optimum substrate ternperature for CdTe deposition was $600^{\circ}C$. To obtain larger grain size and more compact microstructure, CdTe film was initially deposited at 62$0^{\circ}C$, and then deposited at 54$0^{\circ}C$. The CdTe film was annealed at 62$0^{\circ}C$ and $600^{\circ}C$ sequentially to maintain the CdTe film quality. The photovoitaic cell efficiency improved by the "two-wave" process. For constant substrate temperature, the optimum thickness for CdTe was 5-6$\mu m$. Above 6$\mu m$ CdTe thickness, the bulk resistance of CdTe film degraded the cell performance. As the cell area increased the $V_{oc}$ remained almost constant, while $J_{sc}$ and FF strongly decreased because of the increase of lateral resistance of the ITO layer. The optimum thickness of the ITa layer in this study was 300~450nm. In this experiment we obtained the efficiency of 9.4% in the O.5cm' cells. The series resistance of the cell should be further reduced to increase the fill factor and improve the efficiency.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.28-41
• /
• 2022

A road system with CV(Connected Vehicle)s, which is often referred to as a cooperative intelligent transportation system (C-ITS), provides various road information to drivers using an in-vehicle warning system. Road environments with CVs induce drivers to reduce their speed or change lanes to avoid potential risks downstream. Such avoidance maneuvers can be considered to improve driving behaviors from a traffic safety point of view. Thus, empirically evaluating how a given in-vehicle warning information affects driving behaviors, and monitoring of the correlation between them are essential tasks for traffic operators. To quantitatively evaluate the effect of in-vehicle warning information, this study develops a method to calculate compliance rate of drivers where two groups of speed profile before and after road information is provided are compared. In addition, conventional indexes (e.g., jerk and acceleration noise) to measure comfort of passengers are examined. Empirical tests are conducted by using PVD (Probe Vehicle Data) and DTG (Digital Tacho Graph) data to verify the individual effects of warning information based on C-ITS constructed in Seoul metropolitan area in South Korea. The results in this study shows that drivers tend to decelerate their speed as a response to the in-vehicle warning information. Meanwhile, the in-vehicle warning information helps drivers to improve the safety and comport of passengers.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.20 no.5
• /
• pp.467-472
• /
• 1991

In order to investigate the changes of lipid ingredient and fatty acid content in flint corn by a growth process, total lipids from flint corn(Zea may l.) were extracted, purified and fractionated into three lipid classes (neutral lipid ; NL, glycolipid ; GL, phospolipid ; PL) by silicic acid column chromatography (SACC). Non-polar lipid ingredients and fatty acid contents were determined by thin layer chromatography (TLC) and gas chromatography (GC). And non-polar lipid ingredients were quantitatived by TLC scanner. The crude oil among proximare composition increased 2.74% to 4.43% and NL and PL were fractionated by SACC increased 48.5% to 86.02%, 1.01% to 2.73%, respectively. But GL decreased 50.4% to 11.25%. Neutral lipid ingredients identified monoglyceride, were 1.1~3.7%, 11.9~16.1%, 2.3~4.2%, 16.7~21.5% and 58.5~63.6%, respectively. The major fatty acids of NL were linoleic (48.9~61.0%), oleic(22.3~34.2%), palmitic (10.3~11.7%) acids and stearic, linolenic acids were also detected as minor components. The ratio of total unsaturated fatty acid to total saturated fatty acid presented a higher percentage of 5.87~6.34. The physico-chemical characteristics of flint corn lipids were presented as specific gravity presented 0.920, refractive index 1.468, saponification value 191.2, unsaponificable matter 0.97%, acid value 0.58 and iodine value 124.6, respectively.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.754-762
• /
• 1995

Strontium titanate(SrTiO$_3$) thin film was prepared on Si substrates by RF magnetron sputtering for a high capacitance density required for the next generation of LSTs. The optimum deposition conditions for SrTiO$_3$thin film were investigated by controlling the deposition parameters. The crystallinity of films and the interface reactions between SrTO$_3$film and Si substrate were characterized by XRD and AES respectively. High quality films were obtained by using the mixed gas of Ar and $O_2$for sputtering. The films were deposited at various bias voltages to obtain the optimum conditions for a high quality file. The best crystallinity was obtained at film thickness of 300nm with the sputtering gas of Ar+20% $O_2$and the bias voltage of 100V. The barrier layer of Pt(100nm)/Ti(50nm) was very effective in avoiding the formation of SiO$_2$layer at the interface between SrTiO$_3$film and Si substrate. The capacitor with Au/SrTiO$_3$/Pt/Ti/SiO$_2$/Si structure was prepared to measure the electric and the dielectric properties. The highest capacitance and the lowest leakage current density were obtained by annealing at $600^{\circ}C$ for 2hrs. The typical specific capacitance was 6.4fF/$\textrm{cm}^2$, the relative dielectric constant was 217, and the leakage current density was about 2.0$\times$10$^{-8}$ A/$\textrm{cm}^2$ at the SrTiO$_3$film with the thickness of 300nm.

• Journal of Bio-Environment Control
• /
• v.27 no.4
• /
• pp.319-325
• /
• 2018

The aim of the present study was to determine the influence of different fertilizer combinations on the growth, yield, and fruit quality of 'Duke' blueberry cultivar and the water quality of growth medium. The experiment was carried out with three year old 'Duke' blueberry bushes which were cultivated in containers ($60{\times}80{\times}40cm$) filled with 130 L peat moss and 40 L pearlite (v/v). Sawdust was used as the mulch in growth containers. Three different fertilizer combinations (FC) i.e., FC-1 consisted with standard solution, FC-2 consisted with nitrogen reduced by 10% from FC-1, and FC-3 consisted with nitrogen reduced by 20% from FC-1 were tested while, the ground water used as the control. The effects of different fertilizer combinations on shoot diameter, shoot length, number of shoots, leaf length, SPAD value (the relative content of chlorophyll), berry weight, soluble solids content, titratable acidity, and yield per bush in 'Duke' blueberry were examined. Also, the effects of different fertilizer combinations on pH, EC, $NH_4$ and $NO_3$ in 'Duke' blueberry growth medium were monitored. The highest pH and lowest EC, $NH_4$ and $NO_3$ in growth medium was recorded with control treatment during the experiment period. The maximum shoot diameter (3.7 mm) and shoot length (35.7 cm) was recorded for the FC-1. Highest number of shoots (47%) were recorded from 'Duke' blueberry bushes supplemented with FC-1 compared to other treatments. The fertilizer combinations supplemented with nitrogen showed significant influence on leaf length and SPAD value compared to control 'Duke' blueberry bushes. However, the fruit quality attributes, i.e., berry weight, soluble solids content, and titratable acidity were not significant different among fertilizer treatments. The significantly highest yields per bush were recorded for FC-1, FC-2, and FC-3, as 2.2, 2.9, and 2.7 kg, respectively compared to control (0.2 kg). Although, the FC-1 was supplemented with highest nitrogen content it resulted low yield per bush while having high number of shoots and vigorous growth.

• Journal of Life Science
• /
• v.23 no.12
• /
• pp.1436-1444
• /
• 2013

To improve the functionality of black garlic drinks, black garlic extract (5%) and five herb extracts (1%) were mixed in 70:30 (v/v) ratios as BHF1, and BHF2 was prepared using a 3X concentration of BHF1. After the black garlic and herb formulas (BHFs) were administered over the course of five weeks in rats by interval running training, the lipid profiles and the antioxidant enzyme activities were tested. The total phenolic content of the BHFs were significantly higher in BHF2 than they were in BHF1, and their antioxidant activities were dependent upon the total phenolic content. No significant difference was found in the total serum protein levels among the rats in the Ex-con group by interval running training and the rats in the BHFs-fed groups. However, the albumin level was significantly higher in the Ex-BHF2 to Ex-con group. AST and ALT activities significantly decreased in the BHFs-fed groups compared to the Ex-con group. In terms of changes in the serum lipid profiles, no significant difference was found between the specimens that underwent interval running training and those that did not undergo interval running training. Triglyceride levels, total cholesterol, LDL-C, and HTR levels in the serum were significantly decreased in the Ex-BHF2 to Ex-con group. No significant difference was found in the total lipid levels in the livers of the BHFs-fed groups and the Ex-con group. The triglyceride levels and total cholesterol levels in the Ex-BHF2 group were significantly lower compared to another group. Hepatic catalase activity was significantly increased in the Ex-BHF2 group, but SOD and GSH-px activities were significantly increased as the concentration of the BHF. The antioxidant enzyme activities by supplementation of BHFs increased; thus, three intakes of BHF each day could improve antioxidant status against different types of oxidative stress.