• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1248-1254
• /
• 2003

Carbon nanotubes(CNTs) are grown by using Co catalyst metal. CNTs fabricated by PECVD(plasma enhanced chemical vapor deposition) method are studied in terms of surface reaction and surface structure by TEM and Raman analysing method and ate analysed in its electrical field emission characteristics with variation of space between anode and cathode. Acetylene(C$_2$H$_2$) gas is used as the carbon source, while ammonia and hydrogen gas are used as catalyst and dilution gas. The CNTs grown by hydrogen(H$_2$) gas plasma indicates better vortical alignment, lower temperature process, and longer tip, compared to that grown by ammonia(NH$_3$) gas plasma. The CNTs fabricated with Co(cobalt) catalyst metal and PECVD method show the multiwall structure in mid-circle type in tip-end and the inner vacancy of 10nm. Emission properties of CNTs indicate the turn-on field to be 2.6 V/${\mu}{\textrm}{m}$ We suggest that CNTs can be possibly applied to the emitter tip of FEDs and high brightness flat lamp because of low temperature CNTs growth, low turn-on field.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3233-3237
• /
• 2010

A $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_2$ cathode was modified by coating with Li-La-Ti-O, and the effect of the coating thickness on their electrochemical properties was studied. The thickness of the coating on the surface of $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_2$ was increased by increasing the wt % of the coating material. The rate capability of the Li-La-Ti-O-coated electrode was superior to that of the pristine sample. 1- and 2-wt %-coated samples showed considerable improvement in capacity retention at high C rates. However, the rate capability of a 5-wt %-coated sample decreased. All the coated samples showed a high discharge capacity and slightly improved cyclic performance under a high cut-off voltage (4.8 V) condition. Results of a storage test confirmed that the Li-La-Ti-O coating layer was effective in suppressing the dissolution of the transition metals as it offered protection from the attack of the acidic electrolyte. In particular, the 2- and 5-wt %-coated samples showed a better protection effect than the 1-wt %-coated sample.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.3
• /
• pp.373-376
• /
• 2004

A novel Er(III) complex with oxydiacetate and 1,10-phenanthroline was synthesized and its structure and luminescence properties were characterized. The complex of $[Er(ODA){\cdot}(phen){\cdot}4H_2O]^+$ crystallizes in the monoclinic space group $P2_1$/n with a = 12.216(4) ${\AA}$, b = 16.680(2) ${\AA}$, c = 12.627(3) ${\AA}$, ${\beta}=108.30(2)^{\circ}$, V = 2442.7(11) ${\AA}^3$, Z = 4 and ${\rho}=1.841 g/cm^3$. When the complex is excited at the He-Cd 325-nm line, it produces two broad bands spanning the regions 350-650 nm and 1200-1650 nm. The emission band of the complex is characterized by a series of spectral dips in the visible emission profile. The complex exhibits sensitized near- IR emission via two kinds of energy transfers from phen to Er(III): nonradiative and radiative energy transfers.

• Carbon letters
• /
• v.8 no.2
• /
• pp.120-126
• /
• 2007

The effect of cobalt precursor on the structure of Co supported multi-walled carbon nanotubes (MWCNTs) were studied by using X-ray photoelectron spectroscopy (XPS). MWCNTs were treated with a mixture of nitric and sulfuric acids and decorated with cobalt and/or cobalt oxides via aqueous impregnation solutions of cobalt nitrate or cobalt acetate followed by reduction in hydrogen. XPS was mainly used to investigate the phase of cobalt on MWCNTs after reduction with $H_2$ flow at $400^{\circ}C$ for 2 h. Higher cobalt-nanoparticle dispersion was found in the MWCNTS prepared via cobalt nitrate decomposition. A typical XPS spectrum of Co 2p showed the peaks at binding energy (BE) values equal to 781 and 797 eV, respectively. It is found that cobalt nitrate supported MWCNTs is more dispersive and have catalytic activity than that of cobalt acetate supported MWCNTs at same preparation condition such as concentration of precursor solution and reduction environment.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.170-173
• /
• 2007

Cruciform conjugated molecule, 4(DP3T)-benzene bearing terthiophene moieties has been synthesized through Horner-Emmons Reaction using 5-dodecyl-5"-aldehyde-[2,2';5',2"] terthiophene as dendrons and octaethyl benzene- 1,2,4,5-tetrayltetrakis(methylene)tetraphosphonate as the core unit; this molecule has been fully characterized. The terthiophene-based molecule exhibits good solubility in common organic solvents and good self-film forming property. They are intrinsically crystalline as they exhibit well-defined X-ray diffraction patterns from uniform orientations of molecules. Thus, intermolecular interaction can be enhanced to affect the carrier transport phenomena after annealing at $148^{\circ}C$. The semiconducting property of 4(DP3T)-benzene have been evaluated in organic field-effect transistors. 4(DP3T)-benzene exhibit carrier mobility as high as $(6.6{\pm}0.5)$ ${\times}$ $10^{-6}cm^2V^{-1}s^{-1}$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.9
• /
• pp.20-28
• /
• 1992

Dielectric thin film of N/O ($Si_{3]N_{4}/SiO_{2}$) for high density stacked dynamic-RAM cell was formed by LPCVD and oxidation(dry & pyrogenic oxidation methods) of the top 7nm $Si_{3]N_{4}$ film. The thickness, structure and composition of this film were measured by ellipsometer, high resolution TEM, AES and SIMS. The insulating characteristics(I-V characteristics) were investigated by HP 4145, and the characteristics of TDDB (Time Dependent Dielectric Breakdown) were evaluated by using CCST(Current Constant Stress Time) method. In this experiment, The optimum oxidation condition for preparation of good insulating and TDDB characteristics of N/O film was pyrogenic oxidation at 85$0^{\circ}C$ for 30 minutes. The leakage current was reduced from 400pA to 7.5pA when SiO$_{2}$ film with thickness of 2nm was formed on the top of $Si_{3]N_{4}$ film by the pyrogenic oxidation method.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.126-136
• /
• 1996

Synthesis of perfluoromethanesulfonyl fluoride(PFMSF) which is a valuable precursor of perfluoro-chemicals such as surface modifier and fine chemicals was studied by electrochemical fluorination (ECF). In order to determine the termination of preelectrolysis, it was carried to monitor the variation of current during preelectrolysis by means of constant cell voltage operation. In a batch cell, chronopotentiometric electrolysis and various chemical analysis such as GC, GC/MS and If were used to understand the potential change of electrode and synthesis and control of hazardous gases products. Termination of preelectrolysis was determinated by measurement the current and/or detection of $F_2$ gas generation. And during the preelectrolysis, an amount of generated $OF_2$ was shown that a lot of moisture was absorbed from air when a cell was filled with anhydrous hydrogen fluoride( AHF ). Above 4V cell voltage, $F_2$ gas was generated and acted on any form of fluorinating agents. In the ECF of MSC (methane sulfonyl chloride) by constant current operation, the potential of anode was intimately relation with generation of $SO_2F_2$. Exchange of Cl to F was dominatly occured in a initial stage. There were various gaseous products including PFMSF as main product and $C_4$ compounds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.71-75
• /
• 2003

Carbon nanotubes(CNTs) are grown by using Co catalyst metal. CNTs fabricated by PECVD(plasma enhanced chemical vapor deposition) method are studied in terms of surface reaction and surface structure by TEM and Raman analysing method and are analysed in its electrical field emission characteristics with variation of space between anode and cathode. Acetylene($C_2H_2$) gas is used as the carbon source, while ammonia and hydrogen gas are used as catalyst and dilution gas. The CNTs grown by hydrogen($H_2$) gas plasma indicates better vertical alignment, lower temperature process and longer tip, compared to that grown by ammonia($NH_3$) gas plasma. The CNTs fabricated with Co(cobalt) catalyst metal and PECVD method show the multiwall structure in mid-circle type in tip-end and the inner vacancy of 10nm. Emission properties of CNTs indicate the turn-on field to be $2.6\;V/{\mu}m$. We suggest that CNTs can be possibly applied to the emitter tip of FEDs and high brightness flat lamp because of low temperature CNTs growth, low turn-on field.

• Clinical Nutrition Research
• /
• v.3 no.2
• /
• pp.106-114
• /
• 2014

It is generally accepted that diet modification provides beneficial effects on the management of diabetes. In the present study, we evaluated the effects of diet modification on nutrient intake and quality of life in a large sample of diabetic patients. This study was conducted using data from the Korea National Health and Nutrition Examination Survey IV and V (2007-2010). A total of 2,484 of diabetic patients were included in the analysis. Then, we compared the overall quality of dietary intake between diabetic patients with diet modification and those without dietary modification. The result showed that subjects on diabetic diet (DDG) showed lower levels of total cholesterol, triglyceride, and AST before and after the adjustment for covariates (all p < 0.05). The results of nutrient assessment showed that DDG had lower intakes of total energy, fat, and carbohydrate (all p < 0.05), but higher intakes of energy from protein, vitamin B1, vitamin B2, niacin and vitamin C than NDG. (all p < 0.05). In addition, nutritional adequacy ratio of calcium and vitamin B2 were significantly higher in DDG than those in normal diet group (NDG) (p < 0.05). However, we observed no significant differences in quality of life between two groups. In conclusion, diet modification in diabetic patients seemed to be effective to improve blood lipid profile and the adequacy of nutrient intake without sacrificing the quality of life.

• Journal of Sensor Science and Technology
• /
• v.28 no.2
• /
• pp.101-105
• /
• 2019

ZnS substrates with excellent transmittance in the mid-infrared region ($3-5{\mu}m$) were prepared using hot pressing instead of conventional chemical vapor deposition (CVD). Diamond-like carbon(DLC) was coated on either one or both sides of the ZnS substrates to improve their mechanical properties and transmittance. More specifically DLC was coated using CVD with an Ar and $C_2H_2$ mixed gas, and Ge was used as the bonding layer. During CVD, the bias voltage was fixed to 500 V and analyzed by Fourier transform infrared spectroscopy (FT-IR), nanoindenter, scanning electron microscope and energy dispersive spectrometry. Results of hardness analysis using the nanoindenter, showed that DLC coating increased from 5.9 to 17.7 GPa after deposition. The FT-IR spectroscopy results showed that, in the mid-infrared region ($3-5{\mu}m$), the average transmittance of the samples with DLC coating on one and both sides increased by approximately 6% and approximately 11.2% respectively. In conclusion, the DLC coating improved the durability and transmittance of the ZnS substrates.