• Restorative Dentistry and Endodontics
• /
• v.30 no.5
• /
• pp.355-362
• /
• 2005

The purpose of this study was to compare the effect on marginal leakage of a resin surface sealant (Biscover) applied before or after polymerization of composite resin to unsealed composite restorations. Thirty Class V cavities with the occlusal margin in enamel and cervical margin in dentin or cementum were prepared on the buccal surfaces of sound extracted molars and restored with a microfilled light-cured composite resin (Micronew). Restorations were randomly assigned into one of three equal groups (n = 10): a control group - no surface sealing, group 1 - applied Biscover after polymerization of the composite resin. and group 2 - applied Biscover before polymerization of the composite resin. Specimens were thermocycled, immersed in a $20\%$ methylene blue solution for 4 hoots, sectioned longitudinally, and analyzed for leakage at the occlusal and gingival margins. The results of this study were as follows 1. In sealed group, group 2 showed higher microleakage than group 1 at both occlusal and gingival margins. but there was no significant difference between two groups (p > 0.05). 2. Unsealed control group showed a little higher microleakage than sealed group at occlusal margins, and a little Higher or similar microleakage than sealed group at gingival margins (p > 0.05) 3. Control group and group 2 showed significantly less microleakage at the occlusal margins, but group 1 showed no significantly difference between microleakage at the occlusal and gingival margins.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1067-1072
• /
• 2003

The electrical stability of the varistor ceramics composed of Zn-Pr-Co-Cr-Dy oxides-based varistors was investigated at 0.0∼2.0 mol% Dy$_2$O$_3$ content under DC accelerated aging stress. The ceramic density was increased up to 0.5 mol% Dy$_2$O$_3$ whereas further addition of Dy$_2$O$_3$ decreased sintered ceramic density. The density sailently affected the stability due to the variation of conduction path. The nonlinearity of varistor ceramics was greatly improved above 45 in the nonlinear exponent and below nearly 1.0 ${\mu}$A by incorporating Dy$_2$O$_3$. Under 0.95 V$\_$1mA/150$^{\circ}C$/24 h stress state, the varistor ceramics doped with 0.5 mol% Dy$_2$O$_3$ exhibited the highest electrical stability, in which the variation rates of varistor voltage, nonlinear exponent, and leakage current were -0.9%, -14.4%, and +483.3%, respectively. The variation rates of relative permittivity and dissipation factor were +7.1% and +315.4%, respectively. The varistors with further addition of Dy$_2$O$_3$ exhibited very unstable state resulting in the thermal runaway due to low density.

• Microbiology and Biotechnology Letters
• /
• v.38 no.2
• /
• pp.151-157
• /
• 2010

Barley malt produces two different $\alpha$-amylase isozymes (AMY1 and AMY2), which share up to 80% of amino acid sequence identity with each other. However, their enzymatic properties differ remarkably. In this study, five chimeric enzymes between AMY1 and 2 were constructed by staggered extension process (StEP) technique, and their enzymatic properties were characterized. According to the results, chimeric AMY-D2, D8, and E12 showed the mixed or intermediate types of calcium-dependent activity between AMY1 and 2. Meanwhile, only AMY-E10 chimera could be significantly inhibited by barley $\alpha$-amylase/subtilisin inhibitor (BASI) protein. Chimera AMY-C6 showed the same calcium-dependency as AMY1, while AMY-E10 was closely similar to AMY2. As a result, it can be proposed that some amino acid residues in the region II, III, and IV of barley $\alpha$-amylases can play very important roles in the interaction with BASI, and those in III, V, VI, and VII may partly affect on the calcium-dependent activity.

• Microbiology and Biotechnology Letters
• /
• v.48 no.2
• /
• pp.158-166
• /
• 2020

A gene coding for the xylanase was cloned from Paenibacillus woosongensis, followed by determination of its complete nucleotide sequence. This xylanase gene, designated as xyn10A, consists of 1,446 nucleotides encoding a polypeptide of 481 amino acid residues. Based on the deduced amino acid sequence, Xyn10A was identified to be a modular enzyme composed of a catalytic domain highly homologous to the glycosyl hydrolase family 10 xylanase and a putative carbohydrate-binding module (CBM) in the C-terminus. By using DEAE-sepharose and phenyl-sepharose column chromatography, Xyn10A was purified from the cellfree extract of recombinant Escherichia coli carrying a P. woosongensis xyn10A gene. The N-terminal amino acid sequence of the purified Xyn10A was identified to exactly match the sequence immediately following the signal peptide predicted by the Signal5.0 server. The purified Xyn10A was a truncated protein of 33 kDa, suggesting the deletion of CBM in the C-terminus by intracellular hydrolysis. The purified enzyme had an optimum pH and temperature of 6.0 and 55-60℃, respectively, with the kinetic parameters V_max and K_m of 298.8 U/mg and 2.47 mg/ml, respectively, for oat spelt xylan. The enzyme was more active on arabinoxylan than on oat spelt xylan and birchood xylan with low activity for p-nitrophenyl-β-xylopyranoside. Xylanase activity was significantly inhibited by 5 mM Cu²⁺, Mn²⁺, and SDS, and was noticeably enhanced by K⁺, Ni²⁺, and Ca²⁺. The enzyme could hydrolyze xylooligosaccharides larger than xylobiose. The predominant products resulting from xylooligosaccharide hydrolysis were xylobiose and xylose.

• Journal of Korean Ophthalmic Optics Society
• /
• v.15 no.4
• /
• pp.361-366
• /
• 2010

Purpose: HCD ion plating apparatus by hollow cathod discharge method was fabricated and TiN films were deposited on stainless steel by this apparatus with increasing in $N_2$ gas flow and the fine color changes of TiN films were analyzed. Methods: The spectroradiometer and spectrophotometer were used to observe optically the fine color changes of TiN thin films, and XPS was used to analyze the compositions of TiN thin films with increasing in $N_2$ gas flow. Results: The color coordinate of TiN thin film with $N_2$ 120 sccm gas flow showed (0.382, 0.372) which had the mixed colors of gold and silver, and the color coordinate changed to the increasing value of (x,y) with increasing in $N_2$ gas flow which indicated the deep gold color. It was found that the slopes of the reflectances at 550nm were increased with increasing in $N_2$ gas flow. And from the Ti scans using XPS, it was found that the peak heights of 455 eV derived from TiN composition were increased with increasing in $N_2$ gas flow, while the peak heights of 459 eV from $TiO_2$ composition were decreased. Conclusions: The results obtained above were that the color of TiN film with 120 sccm $N_2$ gas flow had been observed from the mixed color of silver and gold due to TiC, $N_2$, TiN on the surface and TiN, $N_2$ inside film, and the color of TiN films changed a deep gold color with increasing in $N_2$ gas flow due to increasing TiN composition.

• Fisheries and Aquatic Sciences
• /
• v.2 no.1
• /
• pp.8-11
• /
• 1999

The optimum boiling condition was determined for fish extracts by response surface model. Model equations were designed with effect of time (T) and the amount of added water (W) on the level of released free amino acid. Based on the high (>0.9) coefficient of determination and low (<0.01) level of significant, those model was approved to be significant. The added water amount of higher regression coefficient $ (\beta_2)$, showed a greater influence on releasing free amino acids than boiling time. The optimum boiling times are 6 hours for crucian carp, 5 hours for bastard halibut, 7 hours for loach and 5 hours for jacopever. The ratio of added water to sample 1 (v/w) could be applied to all fish samples at $100\pm2^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.197-197
• /
• 2012

염료감응형 태양전지 (DSSC)는 다양한 태양전지 중, 가장 환경친화적이고, 생산단가도 낮을 뿐만 아니라 다양한 색상과 투광성을 확보할 수 있어 많은 연구가 진행되어왔다. 하지만 액체 전해질을 사용하는 기존 염료감응형 태양전지는 높은 휘발성과 열 팽창 수축에 따른 전해질 누액의 문제점으로 인하여 최근에는 고체전해질을 이용한 염료감응형 태양전지의 개발이 활발히 이루어지고 있다. 본 연구에서는 스크린 프린팅법을 이용하여 TiO2 광전극을 코팅하고 Mg(OH)2를 솔-젤법을 이용하여 스핀 코팅 하였다. 이후에 $500^{\circ}C$에서 1시간동안 열처리를 통해 MgO 나노 코팅막을 형성하여 고체 박막 태양전지(solid state dye sensitized solar cells)을 제작하였다. MgO 나노 코팅막의 특성은 솔라시뮬레이터를 이용하여 I-V 곡선, transient Voc, dark current를 측정하였고, UV0vis spectroscopy를 이용하여 염료흡착량을 분석하여 코팅막과 효율간의 상관관계를 평가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.257.2-257.2
• /
• 2015

In this paper, we report on the 10.33% efficient thin film/bulk tandem solar cells with the top cell made of amorphous silicon thin film and p-type bulk crystalline silicon bottom cell. The tunneling junction layers were used the doped nanocrystalline Si layers. It has to allow an ohmic and low resistive connection. For player and n-layer, crystalline volume fraction is ~86%, ~88% and dark conductivity is $3.28{\times}10-2S/cm$, $3.03{\times}10-1S/cm$, respectively. Optimization of the tunneling junction results in fill factor of 66.16 % and open circuit voltage of 1.39 V. The open circuit voltage was closed to the sum of those of the sub-cells. This tandem structure could enable the effective development of a new concept of high-efficiency and low cost cells.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.272-276
• /
• 2004

Great strides in organic light emitting device (OLED) technology have resulted in a number of commercial products. To continue this growth into large area displays, for example televisions, an understanding of the mechanisms that drive the OLED device efficiency and lifetime performance is critical. In this work, we consider maximizing the efficiency lifetime product based on phosphorescent OLED ($PHOLED^{TM}$) technology. We report green PHOLEDs with luminous efficiency of 82 cd/A, 5.7 V and 10,000 hours lifetime at 1,000 cd/$m^2$,red PHOLEDs with CIE of (0.67,0.33), 11 cd/A and 35,000 hours lifetime at 500 cd/$m^2$ and recent progress in blue demonstrating efficiencies of 18 cd/A at 200 cd/$m^2$.

• KSBB Journal
• /
• v.10 no.1
• /
• pp.30-37
• /
• 1995

Membrane-bound alcohol dehydrogenase(ADH) was purified to homogeneity from the acetic acid producing bacteria, Acetobacter sp. KM. The enzyme was solubilized and extracted with Triton X-100 and purified using the Mono-Q ion exchange chromatography and Superose 12 gel filtration chromatography. The enzyme was purified to 12-fold with a yield of 30%. The molecular weight of the purified enzyme was to be 335 KDa. SDS-PAGE of the enzyme showed two subunits with molecular weights of 79 KDa and 49 KDa. It indicated that the enzyme consisted of three subunits of the 79 KDa and two subunits of the 49 KDa. The purified .ADH preferentially oxidized straight chain aliphatic alcohol except methanol. Formaldehyde, acetaldehyde and glutaraldehyde were also oxidized. The apparent Km for ethanol was 1.04 mM and the optimum pH and temperature were 5.0∼6.0 and 32$^{\circ}C$, respectively. V2O5 and divalent cation such as ZnCl2 and NiCl2 inhibited enzymatic activity.