• Journal of Ocean Engineering and Technology
• /
• v.20 no.6 s.73
• /
• pp.88-92
• /
• 2006

Large-scale model tests of welded topside joints were carried out to observe the fatigue behavior of API 2W Gr.50 steel produced by POSCO. The fatigue crack behaviors for various loading conditions were measured and investigated around the critical joint sections. The experimental results have been verified with numerical approaches and also compared with the AWS D1.1 and DnV RP-C203 design curves. The large-scale experiment models were fabricated, based on the actual operating east area fixed platform. The dimensions of the models were slightly modified to accommodate the test facilities and capacities. The fatigue test was carried out having ${\Delta}Q$ of T1=705.6kN, T2=749.7kN and T3=793.8kN. The three specimens were statically loaded 20 times, with various loadings of about 50kN intervalsbetween the maximum and minimum loads required in the fatigue tests. This loading removed the residual stress in the specimen before the fatigue tests. The topside joint crack was initiated from the brace heel, where the maximum tensile stress occurred. The API 2W Gr.50 steel satisfied the AWS D1.1 detail category C and DnV RP-C203 detail category F ${\Delta}S-N$ curve.

• Journal of The Korean Astronomical Society
• /
• v.55 no.1
• /
• pp.1-9
• /
• 2022

We present the photometric properties of V608 Cas from detailed studies of light curves and eclipse timings. The light curve synthesis indicates that the eclipsing pair is an overcontact binary with parameters of ∆T = 155 K, q = 0.328, and f = 26%. We detected the third light ℓ₃, which corresponds to about 8% and 5% of the total systemic light in V and R bands, respectively. Including our 6 timing measurements, a total of 38 times of minimum light were used for a period study. It was found that the orbital period of V608 Cas has varied in some combination of an upward parabola and two periodic variations. The continuous period increase with a rate of +3.99 × 10^-7 d yr^-1 can be interpreted as a mass transfer from the secondary component to the primary star at a rate of 1.51 × 10^-7 M_⊙ yr^-1. The periods and semi-amplitudes of the two periodic variations are about P₃ = 16.0 yr and P₄ = 26.3 yr, and K₃ = 0.0341 d and K₄ = 0.0305 d, respectively. The most likely explanation of both cycles is a pair of light-traveling time effects operated by the possible presence of third and fourth components with estimated masses of M₃ = 2.20 M_⊙ and M₄ = 1.27 M_⊙ in eccentric orbits of e₃ = 0.66 and e₄ = 0.52. Because the contribution of ℓ₃ is very low compared to the estimated masses of two circumbinary objects, they can be inferred as very faint compact objects.

• Korean Journal of Environment and Ecology
• /
• v.7 no.2
• /
• pp.187-191
• /
• 1994

A mixed forest community in Tokyusan was studied to determine the adequate plot area of tree stratum for investigating forest community structure. Nineteen nested plots were set up in the studied forest community, and species-area curve and performance curve were established. According to species-area curve, the minimum plot area where a given percentage increase in plot area produced less than the same percentage increase in number of species was 500$m^2$. The minimum plot area where a given percentage increase in plot area produced less than the half of the percentage increase in number of species was 1,000$m^2$. According to performance curve of the importance values of the major species, the minimum plot area where the importance value of the major species was distinguished from each other was 900$m^2$, and the minimum plot area was 500$m^2$ except for a big tree of Pinus densiflora distributed unexpectedly. According to performance curve of species diversity, the minimum plot area was 400$m^2$. Similarity indices between plot area above 900$m^2$ and total plot area were more than 90% and similarity indices between plot area above 400$m^2$ and total plot area were more than 85%. It may be as a conclusion that minimum plot area was generally about 500$m^2$ and in case of requiring more accuracy, minimum plot area was about 1,000$m^2$.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.4
• /
• pp.274-281
• /
• 2017

This paper describes the simple fabrication of an electrode modified with electrochemically reduced graphene oxide (ERGO) for the simultaneous electrocatalytic detection of dopamine (DA), ascorbic acid (AA), and uric acid (UA). ERGO was formed on a glassy carbon (GC) electrode by the reduction of graphene oxide (GO) using linear sweep voltammetry. The ERGO/GC electrode was formed by subjecting a GO solution ($1mg\;mL^{-1}$ in 0.25 M NaCl) to a linear scan from 0 V to -1.4 V at a scan rate of $20mVs^{-1}$. The ERGO/GC electrode was characterized by Raman spectroscopy, Fourier transform infrared spectroscopy, contact angle measurements, electrochemical impedance spectroscopy, and cyclic voltammetry. The electrochemical performance of the ERGO/GC electrode with respect to the detection of DA, AA, and UA in 0.1 M PBS (pH 7.4) was investigated by differential pulse voltammetry (DPV) and amperometry. The ERGO/GC electrode exhibited three well-separated voltammetric peaks and increased oxidation currents during the DPV measurements, thus allowing for the simultaneous and individual detection of DA, AA, and UA. The detection limits for DA, AA, and UA were found to be 0.46, 77, and $0.31{\mu}M$ respectively, using the amperometric i-t curve technique, with the S/N ratio being 3.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.10-12
• /
• 2002

Single Josephson junctions of 50 $\mu$m $\times$ 50 $\mu$m were fabricated for several oxidation conditions to investigate controllabilities of critical current density ($J_{c}$) with the standard KRISS processes. Considering the self-field effect suppressing the observed critical current ($I_{c}$) at high $J_{c}$ region, we could reasonably estimate $J_{c}$ values from I-V observations. The dependence of the estimated $J_{c}$ as a function of exposure, which is equal to pressure(P) times time(t), was well fitted to a curve of $J_{c}$ ~ $(Pt)^{-0.36}$. The maximum $J_{c}$ value at the controllability margin was found to be 4 kA/$cm^{2}$ with the current equipment set up.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.134-138
• /
• 2000

The physical, electrical and piezoresitive characteristics of CrN(chromiun nitride) thin-films on silicon substrates have been investigated for use as strain gauges. The thin-film depositions have been carried out by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(5~25 %)$N_2$). The deposited CrN thin-films with thickness of $3500{\AA}$nd annealing conditions($300^{\circ}C$, 48 hr) in Ar-10 % $N_2$ deposition atmosphere have been selected as the ideal piezoresistive material for the strain gauges. Under optimum conditions, the CrN thin-films for the strain gauges is obtained a high electrical resistivity, $\rho=1147.65\;{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=11.17.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.53-58
• /
• 2001

Solar energy has many advantage like as purity and infinity. Recently many researches about new energy source are processing in several places around the world. In this paper, the virtual implement of solar cell was proposed to solve the problems as reappearance and repetition of some situation in experiment of photovoltaic. To realize the VISC, mathematical model of solar cell for driving converter was studied and the buck converter were compared in viewpoint of tracking error of characteristic curve of solar cell using computer simulation. Also, Output characteristics of system analyzed through an experiment.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1041-1044
• /
• 1992

A solar cell should be operated at the maximum output point on the I-V characteristic curve with constant current and constant voltage in order that the solar energy be fully utilized. According to, in this paper, we describes a controller which can track the maximum power point of a solar arry using current and voltage ripple variation of step up chopper system. The control circuit is desinged such that actual current and voltage are sensed directly from the solar cell array. These two signal are then holded sampling and multiplies by a single chip multiplier.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.10
• /
• pp.924-928
• /
• 2005

We synthesized the two types of photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the two types of photopolymer surface can be obtained. The Voltage-transmittance (V-T) curve in the photoaligned TN cell with UV exposure was different from two type. The response time of photoaligned TN cell was measured about 21 ms in two alkyl chain and about 15 ms in four alkyl chain.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.369-372
• /
• 2001

We studied the electro-optical (EO) performance in the vertical-alignment (VA) - l/4$\pi$ cell photoaligned with polarized UV exposure on a homeotropic photopolymer surfaces. Excellent voltage-transmittance curve in the VA - l/4$\pi$ cell photoaligned with polarized UV exposure for 3 min on the photopolymer containing cholesterol group of 8% can be achieved. The V-T characteristics in the VA-l/4$\pi$ cell photoaligned on the photopolymer surface can be improved by increasing cholesteryl group. For response time measurement, the transmittance characteristics of the VA-l/4$\pi$ cell photoaligned on the photopolymer surface was better than that of the VA-l/4$\pi$ cell rubbingaligned on a polyimide(Pl) surface.