• Transactions of Materials Processing
• /
• v.14 no.2 s.74
• /
• pp.126-132
• /
• 2005

The isothermal forging design of a Ti-6Al-4V wing shape was performed by 3D FE simulation. The design focuses on near-net shape forming by the single stage. The process variables such as the die design, pre-form shape and size, ram speed and forging temperature were investigated. The main design priorities were to minimize forging loads and to distribute strain uniformly in a given forging condition. The FE simulation results for the final process design were compared with the isothermal forging tests. The instability of deformation was evaluated using a processing map based on the dynamic materials model(DMM), including flow stability criteria. Finally, a modified process design for producing a uniform Ti-6Al-4V wing product without forming defects was suggested.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.3
• /
• pp.225-235
• /
• 2013

Cutter forces acting on a disc cutter in TBM are the key parameters for TBM design and its performance prediction. This study aimed to experimentally evaluate cutter forces with different ring shapes in a hard rock. The stiffness of a cutter ring was indirectly estimated from a series of full-scale linear cutting tests. From the experiments, it was verified that the rolling stress acting on a V-shape disc cutter was much higher than on a CCS disc cutter even though the penetration depth by a V-shape disc cutter could be increased in the same cutting condition. Finally, it is suggested that a prediction model considering the shape parameters of a disc cutter should be used for its better prediction.

• Korean Journal of Oriental Medicine
• /
• v.6 no.1
• /
• pp.29-46
• /
• 2000

The clinical application of constitutional Diagnosis is the most important part of Sasang constitutional medicine. It has been studied in various way. The study of morphologic characteristics on the head and face has been identified but didn't considered the Variations of age and sex. For the statistic analysis of the correlation between the sasang constitution and the shape of the face, the head-facial part of 182 cases(the group of throughout the age) and 69 cases(the group of age 30 to 40) were measured by Martin's measurement and analysis of a) the measurement value of height and the component ratio from the Gnathion to each part of face by constitution. b) the measurement value of depth and the component ratio from T-projected to each part of the face by constitution. c) the measurement value of breadth and component ratio between each parts of the facial breadth by constitution. d) the characteristics on each part of face by constitution. e) the result of discriminant analysis about the constitution Authors obtained the results from the study as follows: 1. Taeum-In group is characterized by the value of variables had a tendency to maximum value in throughout the age, the charateristics that the total group show is the shape of face is wide shape in horizontally and flat, the nasal breadth is wider than other constitutions, the lips is narrower than Soyang-In in horizontally and thick shape in vertically, and the biogonial breadth is more developed than other constitutions, so lower face is developed. The charateristics that only the age of 30 40 group show is that the lips is thicker than Soeum-IN. The projection of inter-eyebrows is more projected than Soyang-IN. 2. Soeum-IN group is characterized by the value of variables had a tendency to minimum value in throughout the age. The characteristics that the total group show is the lips is thiner than other constitutions, the breadth of eyes is wider than other constitutions, the difference between sellion and nasal breadth is to be little. The charateristics that only the age of 30 40 group show is that the ratio of upper face in physiognomic face is lager than Soyang-IN. 3. The total age group of Soyang-In is characterized by the shape of face is long in vertically and narrow in horizontally, the total eyebrow breadth and lips and philtrun is wider than other constitutions. The charateristics that only the age of 30 40 group is characterized by the projection of sellion is more projected than Taeum-IN. 4. The values which showed significance in both age group V76, V52, V54, V55, V57, V59, V64, V65, V67, V88, V89, V148, V150, V151, V155, V160, V161, V28, V50, V99, V102, V167, V169, V173, V175, V177, V181 are 27 in all. 5. The values which was significant in the age 30 to 40 group V77, V78, V79, V109, V140, V142, V143, V166, V174 are 9 in all.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.243-246
• /
• 2004

W CMP 공정에서 abrasive 의 size 및 shape 에 따른 CMP 거동에 대해 관찰하였으며, 주요 제거 막질인 W 막질과 stopping layer 로 사용되는 Oxide 막질에 대한 압력(P)과 상대 속도(V) 영향성을 관찰하였다. CMP 제거량이 입자의 size 변화에 의존한다는 기존의 이론과는 달리 응집도(aggregate ratio) 변화가 주요 변수임을 밝혀 내었다. 한편, 각 막질에 대한 P,V 영향성 평가를 통해, 변형된 Prestonian equation 이 abrasive size 및 shape 에 상관없이 W 막질의 제거 거동을 설명하는데 중요한 역할을 수행함을 보였다. 그렇지만, W CMP 공정에서 stopping layer 로 사용되는 oxide 막질의 거동을 설명하는 데에는 어려움이 있었으며, 특히 P,V 에 의한 비선형적 removal rate(RR) 거동발생으로 인해 기존의 이론치와는 많은 차이를 나타내었다. 또한, abrasive size 와 shape 에 따라서도 복잡한 거동을 나타낸다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.5
• /
• pp.337-344
• /
• 2015

As many of armored vehicles are seriously exposed to threat of IEDs(Improvised Explosive Devices) in the Afghanistan war and the Iraq war. V-shaped military vehicles are deeply studied in order to protect crews and mounted soldiers against land mines. Generally the experiment on full-scaled V-shaped structure needs excessively high cost, which becomes a huge barrier to study. In this paper, we explore the possibility to make a half-scaled model of the V-shaped structure by using the geometric similarity scaling. We demonstrate the geometric similarity scaling between the original model and the half-scaled model is established on the momentum and deflections of structure via computer simulations and experiments. At this stage, we conduct only numerical analysis of predicting vibration of V-shaped structure because measuring vibration of structure is difficult in the mass-explosion experiment, which is remained as future work.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3410-3415
• /
• 2014

The heat generated by electronic devices can result in performance degradation. Therefore, a heat sink has been used to release the operating heat into the air outside. This study addressed a methodology for a heat sink with an inner tunnel. Under forced convection conditions, the heat transfer characteristics were different so the cooling and heating performances were studied for the heat sink with an inner tunnel. This was evaluated by performing the experimental test examining the heat transfer characteristics related to the variance in time and temperature distribution. In the cooling experiment, the temperature of the A-shape was lower than that of the B-shape, when the voltage was 10 V. These experimental results indicate the optimal cooling effect. In a heating experiment, the temperature of the A-shape was higher than that of the B-shape, when the voltage was 13 V. The experimental results showed that the temperature and efficiency of the A-shape were higher than those of the B-shape.

• Design & Manufacturing
• /
• v.11 no.3
• /
• pp.46-50
• /
• 2017

Press processing is one of the best machining methods capable of mass production, satisfying dimensional, shape and quality among the methods of processing a metal plate. Among them, Fine blanking is a method of obtaining a precise cross-section such as machining of the shear surface shape. In this research, Using SCP-1 and SHP-1 materials. The deformation behaviors of the material flow affecting the die height of the shear section in accordance with the position of the V-ring in the Fine blanking were compared and analyzed. Result of interpretation, It was confirmed that the force acts on the position where the material flow direction accurately forms the die roll that the material of SCP-1 is at a position of 1.5 mm and the material of SHP-1 is at 2.0 mm. As a result, it was confirmed that the state of fo1111ing the shear surface by the V-ring was excellent. Using analysis results, In the experiment, the height of the die roll was considered by applying The position of the V-ring was 1.5 mm in SCP-1 and 2.0 mm in SHP-1. As a result of comparing the height of the die rolls, the height values of the die rolls were different from each other, It has been considered that the tendency of the die rolls to coincide with each other. It is considered that the difference of the die roll height is caused by the pressure input of the V-ring. In this study, the deformation behavior of the material(In addition to the position of the V-ring, the flow direction of the material depends on the shape of the V-ring and the Indentation amount) is considered to be an important factor in determining die roll height.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.2 s.41
• /
• pp.7-15
• /
• 2007

A numerical procedure for optimizing the shape of three-dimensional channel with V-shaped ribs extruded on both walls has been carried out to enhance the turbulent heat transfer. The response surface based optimization is used as an optimization technique with Reynolds-averaged Wavier-stoked analysis. Shear stress transport (SST) turbulence model is used as a turbulence closure. Computational results for average heat transfer rate show good agreements with experimental data. The objective function is defined as a linear combination of heat transfer and friction loss-related terms with a weighting factor. Three dimensionless variables such as, rib pitch-to-rib height ratio, rib height-to-channel height ratio, and the attack angle of the rib are chosen as design variables. Nineteen training points obtained by D-optimal designs for three design variables construct a reliable response surface. In the sensitivity analysis, it is found that the objective function is most sensitive to the ratio of rib height-to-channel height ratio. And, optimal values of design variables have been obtained in a range of the weighting factor.

• Nuclear Engineering and Technology
• /
• v.55 no.12
• /
• pp.4678-4684
• /
• 2023

Using the Monte Carlo method, the impact of the angular distribution of the electron source on the dose distribution for the 2.5 MeV ELV electron accelerator was explored. The experiment measured the 3-D dose distribution in the irradiation chamber for electron energies of 1.0 MeV and 2.5 MeV. The simulation used the MCNP6.2 code to evaluate three angular distribution models of the source: a mono-directional beam, a cone shape, and a triangular shape. Of the three models, the triangular shape with angles θ = 30°, φ = 0° best represents the angle of the scan hood through which the electron beam exits. The MCNP6.2 simulation results demonstrated that the triangular model is the most accurate representation of the angular distribution of the electron source for the 2.5 MeV ELV electron accelerator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.205-206
• /
• 2010