• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.4
• /
• pp.268-272
• /
• 2002

This paper presents a novel microfabrication technology of 3D microstructures with inclined/rotated UV lithography using negative photoresist, SU-8. In some cases, reflected UV as well as incident UV is used to form microstructures. Various 3D microstructures are simply fabricated such as embedded channels, bridges, V-grooves, truncated cones, and so on.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1992.02a
• /
• pp.3-10
• /
• 1992

pphotostimulated desorpption of NO chemisorbed on ppt(001) at 80K has been studied by the (1+1)-resonance-enhanced multipphoton ionization((1+1)-REMppI) technique. A linearly ppolarized ArF excimer laser ( =193 nm, 6.41eV) is used as the ppumpp laser. A high adsorpption rate selectivity was found in the expposure deppendence of the NO desorpption yield. The NO desorpption yield increases drastically when the amount of NO expposure exceeds ~1.8 L. This result shows that the amount of NO sppecies with a large cross section for pphotostimulated desorpption increases drastically at higher NO coverages. Using scanning tunneling microscoppy, we have observed structural modifications of the chlorinated Si(111)-7$\times$7 surface induced by 266nm laser irradiation. At very low laser fluence of 0.7mJ/$\textrm{cm}^2$, at which thermal desorpption can be ignored, a pperiodic stripped ppattern of a single domain is imaged. This ppattern consists of flat terraces and narrow grooves of ~60 and ~10A in width, resppectively.

• Journal of the Optical Society of Korea
• /
• v.4 no.1
• /
• pp.62-65
• /
• 2000

A new type of multi-viewing zone screen for multiview 3-D display is described. The screen is made by stacking a Fresnel lens and a reflective prism array plate. The screen performs both focusing and beam dividing functions and directs very narrow light beams to three viewing zones for three spectators. The results of experimental testing of the screen have demonstrated that current technology of Fresnel lens and prism grooves on PMMA(Ploymethyl Methacrylate) allows manufacture of screen having a pixel size of about 1-2 mm. This size is reasonable enough for a screen with dimensions about 1m size. Optical qualities of Fresnel lenses and grooved prism arrays achieve an angular resolution for the screen of several angular minutes.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.162-170
• /
• 2001

In torch weaving in arc welding on V groove, the heat input distribution on groove surface is a main factor determining the bead shape and the weld quality with and without the weld defects such as undercut, overlap, etc. In this study, we calculate the heat input varying with the welding current, arc voltage, welding speed and the touch weaving condition using numerical method. And we investigate the heat input distribution on groove surface while applying the various grooves having 2 dimensional heat sources.

• Conservation Science in Museum
• /
• v.20
• /
• pp.13-30
• /
• 2018

Ancient metal objects with inlaid designs were mainly decorated using the wire inlay technique in which "V"- or "U"-shaped grooves were cut in a metal object and then filled with gold or silver. Previous studies on ancient metal objects featuring wire inlay generally attempted to ascertain the inlay techniques applied by examining photomicroscopes acquired during conservation treatment. However, they had limitations when examining wire inlay technique to the minute details. Wire inlay technique can be better investigated by enlarging X-ray films of relics using stereoscopic microscopy under transmitted light. The core processes of the wire inlay technique involve cutting grooves using a chisel and creating the inlay wires, but researchers hold varying opinions about the two processes. This study analyzed the entirety of the materials able to shed light on the main processes applied in Baekje wire inlay by examining X-ray films of relics through stereoscopic microscopy. This exhaustive research revealed that two types of techniques were used for wire inlay during the Baekje period. One is a plastic process of engraving dotted lines using a chisel and is found mostly in objects from the Cheonan and Gongju areas. The other is a cutting process that incises fine lines and was used mostly in relics from the Osan, Seosan, and Wanju areas. It is likely that the Baekje wire inlay techniques feature regional differences because the respective techniques were used or introduced by different groups of people.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.82-88
• /
• 2011

The artificial increase in the solar intensity incident on solar cells using lenses or mirrors can allow solar cells to generate equivalent power with a lower cost. There are two types of concentration optics for solar energy conversion. One is to use mirrors, and the other is to use Fresnel lenses. The gains that can be achieved with a Fresnel lens or a parabolic mirror are compared. The result showed the gains are comparable and the two configurations were developed competitively. In application areas of Fresnel lenses as solar concentrators, several variations of design were devised and tested. Some PV systems still use commercially available flat Fresnel lenses as concentrators. A convex linear Fresnel lens to improve the concentration ratio and the efficiency is devised and flat linear Fresnel lens in thermal energy collection is utilized. In this study, we designed and optimized flat Fresnel lens and the 'light pipe' to develop 500X concentrated solar PV system. In the process, we compare the transmission efficiencies according to groove types. We performed rigorous ray tracing simulation of the flat Fresnel lenses. The computer aided simulation showed the 'grooves in case' has the better efficiency than that of 'grooves out case'. Based on the ray-trace results we designed and manufactured sample Fresnel lenses. The optical performance were measured and compared with ray-trace results. Finally, the optical efficiency was measured to be above 75%. All the design and manufacturing were performed based on that InGaP/InGaAs/Ge triple junction solar cell is used to convert the photon energy to electrical power. Field test will be made and analyzed in the near future.

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.1
• /
• pp.1-7
• /
• 2022

As a power transmission element, the timing belt is a toothed transmission belt that takes advantages of V-belts and gears. It has characteristics of non-slip and low noise. It is used as a power transmission device when transmitting power from a rotating shaft or linear motion in a mechanism. Rotation can be accurately transmitted through a belt pulley with grooves like a gear and a timing belt with grooves to precisely match with the belt pulley. In particular, in the mechanism in which the timing belt is used for the output shaft, the dynamic characteristics including the rigidity of the timing belt determine the transmission characteristics of the system, so its importance increases. In this paper, a stiffness reinforced belt that can be applied to a timing belt with a limited range of motion to increase its stiffness is proposed. To study the dynamic characteristics of the stiffness reinforced belt, the equation of motion for the stiffness reinforced belt was established, and a simulation model for the stiffness reinforced belt was created and analyzed. In order to confirm the analysis results of the motion equation and simulation model, a 1-axis rotation experimental equipment using a stiffness reinforcing belt was developed and the experiment was conducted. Through motion equations, simulation models, and experiment results, it was confirmed that the stiffness and dynamic characteristics of the timing belt could be improved by applying the proposed stiffness reinforcement belt.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2660-2665
• /
• 2007

Turbulent boundary-layer over a micro-riblet film(MRF) was investigated experimentally. The MRF has sharp V-shaped micro scale grooves of $300{\mu}m$ in width and $176.8{\mu}m$ in height. Particle image velocimetry(PIV) system was employed to measure velocity fields of flow over the MRF coated plate. Flow over a smooth plate was also measured for comparison. The PIV measurements were taken in the streamwise wall-normal planes at Re$\theta$= 985 and 2342. Vortex structures of the flow were analyzed by extracting the swirling strength as an unambiguous vortex-identification criterion. As a result the number of spanwise vortices with clockwise(negative) rotation decreases rapidly in the near-wall region(y<0.2h), but decreases slowly in the outer region(0.2h

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.1-6
• /
• 2003

In injection molding of an optical disk, a toric lens, etc., their performance depends on the transcription preciseness of fine surface structure of a mold. However, transcription behavior has not been made clear yet, because transcription is made in very short time and the structure is very small. In this paper, transcription properties have been examined, by using V-grooves of various sizes. machined on mold surfaces, and the following results are obtained. (1) Transcription properties have been made clear experimentally and it was found that the mold temperature $T_D$ makes great influence on the transcription property and that compression applying time $t_c$ should be taken more than 2.0s for fine transcription. (2) A mechanical model of transcription process, in consideration with strain recovery due to viscoelastic property of polymer. is proposed. (3) Simulation results agree with experimental ones fairly well. It means that the transcription model is useful for estimation of transcription property in advance of an actual. injection molding.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.40-43
• /
• 2004

Stamps for microcontact processing are fabricated by casting elastomer such as PDMS on a master with a negative of the desired pattern. After curing, the PDMS stamp is peeled away from the master and exposed to a solution of ink and then dried. Transfer of the ink from the PDMS stamp to the substrate occurs during a brief contact between stamp and substrate. Generally, negative-tone masters, which are used for making positive-tone PDMS stamps, are fabricated by using photolithographic technique. The shortcomings of photolithography are a relative high-cost process and require extensive processing time and heavy capital investment to build and maintain the fabrication facilities. The goal of this study is to fabricate a negative-tone master by using Nano-indenter based patterning technique. Various sizes of V-grooves and U-groove were fabricated by using the combination of nanoscratch and HF isotropic etching technique. An achieved negative-tone structure was used as a master in the PDMS replica molding process to fabricate a positive-tone PDMS stamp.