• Korean Chemical Engineering Research
• /
• 제44권2호
• /
• pp.179-186
• /
• 2006

$TiO_2$를 나노튜브(nanotube)와 나노입자(nanoparticle)의 두 가지 형태로 제조하여 닥터 브레이드 방법과 $450^{\circ}C$에서의 소결 공정을 통하여 다공성막으로 제조하였다. 이 다공성막을 작용물질로 사용하여 염료감응형 태양전지를 제조하고 그 특성을 조사하였다. $TiO_2$ 나노입자는 수소화 티탄염 나노튜브를 $180^{\circ}C$에서 24시간 동안 가수열분해 처리함으로써 합성하였다. 이 $TiO_2$ 나노입자를 다공성막으로 사용하여 제작한 염료감응형 태양전지의 에너지 효율(${\eta}$)은 8.07％이며, 개방전압(open-circuit potential, $V_{OC}$), 단락전류(short-circuit current, $I_{SC}$)와 fill factor(FF) 값은 각각 0.81 V, $18.29mV/cm^2$와 66.95％이었다. 나노튜브 $TiO_2$를 제조할 경우에는 NaOH 용액의 농도를 3M과 5M로 변화시켰다. 그 결과 3M NaOH 용액에서 합성된 나노튜브 $TiO_2$를 다공성막으로 사용하여 제작된 염료감응형 태양전지의 에너지 효율(${\eta}$)은 6.19％이었으며, $V_{OC}$, $IV_{SC}$와 FF 값은 각각 0.77 V, $12.41mV/cm^2$와 64.49％이었다. 반면에 5 M NaOH에서는 전자이동성이 좋지 않아 효율이 4.09％로 감소하였다. 본 연구 결과 가수열분해법에 의해 제조한 $TiO_2$ 나노입자로 제조한 염료감응형 태양전지의 효율이 가장 높았다.

• 대한화학회지
• /
• 제52권2호
• /
• pp.124-132
• /
• 2008

H3SO4(M: 몰농도) 용액에서 탄소강의 부식방지제로 Furfural hydrazone 유도체의 효과를 질량손실법 및 정전류극성법을 사용해 연구하였다. 이들 유도체 존재하에서 탄소강의 부식속도가 급격히 감소함을 관찰하였다. 이 연구로부터 부식방지효율은 부식방지제 농도가 증가함에 따라 증가하였고 I와 SCN을 첨가하면 부식방지효율은 더욱 증가되었다. 질량손실법을 사용해 5×10-6 M의 유도체가 있을 때와 없을 때 30-60oC 사이에서 탄소강 부식에 미치는 온도 효과를 보았다. 부식과정에 대한 활성화에너지(Ea*)와 다른 열역학적 변수들을 계산하였고 이들에 대해 논의하였다. 정전류극성법을 통해 유도체들이 혼합형 방지제로 작용함을 알았고 외부전류를 흘려주었을 때 음극은 더욱 분극되었다. 3M H3SO4 용액에서 탄소강 표면에 이들 유도체들의 흡착은 Frumkin의 흡착등온을 따랐다. 이들 유도체들의 화학구조를 통해 부식방지 메커니즘을 설명하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.70.1-70.1
• /
• 2015

The facility for RAON superconducting heavy-ion accelerator at a beam power of up to 400 kW will be produced rare isotopes with two electron cyclotron resonance (ECR) ion sources. Highly charged ions generated by the ECR ion source will be injected to a superconducting LINAC to accelerate them up to 200 MeV/u. During the acceleration of the heavy ions, a good vacuum system is required to avoid beam loss due to interaction with residual gases. Therefore ultra-high vacuum (UHV) is required to (i) limit beam losses, (ii) keep the radiation induced within safe levels, and (iii) prevent contamination of superconducting cavities by residual gas. In this work, a RAON vacuum design for all the accelerator system will be presented along with Monte Carlo simulation of vacuum levels in order to validate the vacuum hardware configuration, which is needed to meet the baseline requirements.

• Transactions on Electrical and Electronic Materials
• /
• 제14권1호
• /
• pp.43-46
• /
• 2013

In order to develop electrical insulation material, organically modified layered silicate was incorporated into an epoxy matrix to prepare nanocomposite. Transmission electron microscopy (TEM) observation showed that organophillic clay was in an exfoliated state, while hydrophilic clay was not dispersed into nanolayers within the epoxy matrix. Epoxy/organophilic clay (2.8 wt%) nanocomposite was mixed and cured at $150^{\circ}C$ for 4.5 hr. I-V characteristics, volume resistance and dielectric properties for the cured nanocomposite were estimated. Current density increased with increasing temperature, and volume resistance decreased with increasing temperature, in neat epoxy and epoxy/organophilic clay (2.8 wt%) nanocomposite. As frequency increased, the dielectric loss value decreased in the two systems.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.303-306
• /
• 2005

This paper presents the frequency-dependent characteristics of leakage currents flowing through ZnO surge arrester block. The leakage current-voltage (I-V) characteristic curves of the commercial ZnO surge arrester blocks were measured. The resistive leakage current was found to increase with increasing frequency in the low conduction region. The capacitance of ZnO block was independent of the magnitude and frequency of the applied voltage. The power losses of ZnO block increase as the frequency of applied voltage increases, because of the dielectric loss related to the frequency of the test voltage.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1333-1335
• /
• 2007

We studied the surface defects and the current distributions of ITO thin films by reflected electron energy loss spectroscopy (REELS) and conductiveatomic force microscope (c-AFM). The ohmic behavior of ITO thin film was observed at $230\;^{\circ}C$ annealed sample. The defects related to the electronic structure decreased after anneal process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.239-242
• /
• 1998

The (S $r_{0.85}$C $a_{0.15}$)Ti $O_3$ (SCT) thin films are deposited on Pt-coated electrode using RF magnetron sputtering method at various substrate temperature. Dielectric constant of SCT thin films is increased with increased as the deposition temperature and changes almost linearly in temperature ranges from -80 to +90[$^{\circ}C$]. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films is observed above 200[kHz]. V-I characteristics of SCT thin films show the increasing leakage current with the increases of deposition temperature.ure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.157-161
• /
• 2000

The electronic ballasts for low pressure discharge lamps are produced and commercialized. However, the electronic ballasts for high pressure lamps are now in progress because of poor reliability and high cost. The major case of troubles with electronic ballasts are thermal destruction of semiconductor output switches due to non ideal i-v characteristics of switch. The loss converts to heat and rises the temperature of switch and it increases proportionally to switching frequency and value of current and voltage. This study shows the variable frequency ballasts which can suppress the heating of switches efficiently. It is used for the limitation the switch current and the rising temperature of switch by impedance variation of lamp inductor. As a result, initial warm-up time of the proposed ballasts was faster than that of magnetic ballasts about 90 msec. Power factor of tested ballasts follow as ; input and output average of magnetic ballasts are 93 [%] and 86 [%], respectively, And proposed ballasts are 97 [%] and 99 [%], respectively.

• Advances in concrete construction
• /
• 제8권4호
• /
• pp.247-255
• /
• 2019

Several reinforced concrete structures that get deteriorated by rebar corrosion are retrofitted using Carbon Fiber Reinforced Polymer (CFRP). When rebar comes in direct contact with CFRP, rebar may corrode, as iron is more active than carbon. Progression of corrosion of rebar in strengthened RC structures has been carried out when rebar comes in direct contact with CFRP. The experimentation is carried out in two phases. In phase I, corrosion of bare steel bar is monitored by making its contact with CFRP. In phase II, concrete specimens with surface bonded CFRP were casted and subjected to the realistic exposure conditions keeping direct contact between rebar and CFRP. Progression of corrosion has been monitored by various parameters: Half-cell potential, Tafel extrapolation and Linear Polarisation Resistance. On termination of exposure, to find residual bond stress between rebar and concrete, pull-out test was performed. Rebar in contact with CFRP has shown substantially higher corrosion. The level of corrosion will be more with more area of contact.

• 한국통신학회논문지
• /
• 제36권2A호
• /
• pp.100-107
• /
• 2011

Algorithms based on the QR decomposition of the equivalent space-time channel matrix have been proved useful in the detection of V-BLAST systems. Especially, the parallel detection (PD) algorithm offers ML approaching performance up to 4 transmit antennas with reasonable complexity. We show that when directly applied to STBCs, the PD algorithm may suffer a rather significant SNR degradation over ML detection, especially at high SNRs. However, simply extending the PD algorithm to allow p ${\geq}$ 2 candidate layers, i.e. p-PD, regains almost all the loss but only at a significant increase in complexity. Here, we propose a simplification to the p-PD algorithm specific to STBCs without a corresponding sacrifice in performance. The proposed algorithm results in significant complexity reductions for moderate to high order modulations.