• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.5
• /
• pp.313-322
• /
• 2001

The effects of Zr/Ti concentration ratio in PLZT (10/y/z) thin films prepared by sol-gel method are investigated for the NVFRAM application. Rosette and pyrochlore phase are observed in PLZT (10/40/60) thin film and the (100) orientation, the grain size, and the surface roughness of PLZT thin films increase due to the increase of Ti amount in Zr/Ti concentration ratio. As Ti amount of Zr/Ti concentration ratio increases, the dielectric constants at 10KHz decrease from 600 to 400, while the loss tangents increase from 0.028 to 0.053 and the leakage current densities at 170 kY/cm decrease from 1.64$\times$10$^{-6}$ to 1.26$\times$10$^{-7}$ A/$\textrm{cm}^2$. In the results of hysteresis loops measured at $\pm$ 170 ㎸/cm, the remanent polarization and the coercive field increase from 6.62 to 12.86 $\mu$C/$\textrm{cm}^2$ and from 32.15 to 56.45 ㎸/cm, respectively, according to the change from 40/60 to 0/100 in Zr/Ti concentration ratio. Fatigue and retention properties also improve much as the Zr/Ti concentration ratio change from 40/60 to 0/100. After applying 10$^{9}$ square pulses with $\pm$5V, the remanent polarization of the PLZT (10/40/60) thin film decreases 50％ from the initial state while that of the PLZT (10/0/100) thin film decreases 30％. In the results of retention measurements of 10$^{5}$ s, the remanent polarization of the PLZT (10/0/100) thin film decreases only 11％ from the initial state, while that of the PLZT (10/40/60) thin film decreases 40%.

• Journal of Sensor Science and Technology
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2003

CsI single crystals doped with lithium, potassium or rubidium were grown by using Czochralski method at Ar gas atmosphere. The energy resolutions of CsI(Li:0.2 mole%), CsI(K:0.5 mole%) and CsI(Rb:1.5 mole%) scintillators were 14.5%, 15.9% and 17.0% for $^{137}Cs$(0.662 MeV), respectively. The energy calibration curves of CsI(Li), CsI(K) and CsI(Rb) scintillators were linear for $\gamma$-ray energy. The time resolutions of CsI(Li:0.2 mole%), CsI(K:0.5 mole%) and CsI(Rb:1.5 mole%) scintillators measured by CFT(constant-fraction timing method) were 9.0 ns, 14.7 ns and 9.7 ns, respectively. The fluorescence decay times of CsI(Li:0.2 mole%) scintillator had a fast component and slow one of ${\tau}_1=41.2\;ns$ and ${\tau}_2=483\;ns$, respectively. The fluorescence decay times of CsI(K:0.5 mole%) scintillator were ${\tau}_1=47.2\;ns$ and ${\tau}_2=417\;ns$. And the fluorescence decay times of CsI(Rb:1.5 mole%) scintillator were ${\tau}_1=41.3\;ns$ and ${\tau}_2=553\;ns$. The phosphorescence decay times of CsI(Li:0.2 mole%), CsI(K:0.5 mole%) and CsI(Rb:1.5 mole%) scintillators were 0.51 s, 0.57 s and 0.56 s, respectively.

• Korean Journal of Food Science and Technology
• /
• v.41 no.6
• /
• pp.706-711
• /
• 2009

Hepatoprotective effects of corn gluten hydrolysates (CGH) were investigated in rats orally treated with ethanol (30%(v/v), 3 g/kg body weight/day) for 4 weeks. Six-week old Sprague-Dawley male rats were divided into four dietary groups: normal diet (N), alcohol diet (E), E+CGH 1% diet (CGH-1%), and E+CGH 3% diet (CGH-3%). Body weights and liver indices were not significantly different among the four groups. However, food intakes were lower in the CGH groups than in the normal group (p<0.05). The administration of CGH significantly reduced serum alkaline phosphatase activity by 30% compared to the alcohol diet group. Among the antioxidative enzymes assessed, catalase activity was significantly decreased by 79% in the CGH diet groups compared to the alcohol diet group. In comparison to the alcohol-treated group, aldehyde dehydrogenase activity was increased by 20%, while microsomal ethanol oxidizing system activity was decreased by 20% in the CGH-treated groups. Furthermore, the area under the curve of the blood acetaldehyde concentration versus time profile after the administration of ethanol was significantly lower for the CGH rats than for the ethanol or asparaginic acid treated groups. Thus, CGH seems to offer beneficial effects by protecting against ethanol-induced hepatotoxicity by improving the acetaldehyde-related metabolizing system.

• Journal of the Korean Vacuum Society
• /
• v.16 no.1
• /
• pp.27-32
• /
• 2007

We have investigated photoluminescence(PL) spectra of four $In_xGa_{1-x}N(x=0.15)/GaN$ multiple quantum well(MQW) structures with different well widths in order to study a phenomenon on crystal phase separation. The asymmetic behavior of PL spectra becomes stronger with increase of the well width from 1.5 nm to 6.0 nm, which indicates dual-peak nature. Analyzing the dual-peak fit PL spectra, we have observed that the intensity of low-energy shoulder peak rapidly becomes stronger, compared to that of high-energy peak corresponding to a transition in InGaN QW. It suggests that InGaN QW has two phases with tiny different In compositions, and that In-rich(InN-like) phase forms more and more relatively than stoichiometric InGaN(x=0.15) phase by the InN phase separation mechanism as the QW width increases. PL spectrum of 6.0-nm sample shows an additional peak at low-energy lesion(${\sim}2.0\;eV$) whose energy position is almost the same as a defect band of yellow luminescence frequently observed in GaN epilayers. It may be due to a defect resulted from In deficiency formed with development of the phase separation.

• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.803-809
• /
• 2005

The purpose of this study is to investigate the mechanical characteristics of plain and steel fiber high strength concrete under uniaxial and biaxial loading condition. A number of plain and steel fiber high strength concrete cubes having 28 days compression strength of 82.7MPa(12,000 psi) were made and tested. Four principal compression stress ratios ($\sigma_2/\sigma_1$=0.00, 050, 0.75 and 1.00), and four fiber concentrations($V_f$ =0.0, 0.5, 1.0 and $1.5\%$) were selected as major test variables. From test results, it is shown that confinement stress in minor stress direction has pronounced effect on the strength and deformational behavior. Both of the stiffness and ultimate strength of the plain and fiber high strength concrete Increased. The maximum increase of ultimate strength occurred at biaxial stress ratio of 0.5($\sigma_2/\sigma_1=0.5$) in the plain high strength concrete and the value were recorded $30\%$ over than the strength under uniaxial condition. The failure modes of plain high strength concrete under uniaxial compression were shown as splitting type of failure but steel fiber concrete specimens under biaxial condition showed shear type failure. The values of elastic modulus were also examined higher than that from ACI and CEB expression under biaxial compression condition.

• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.106-112
• /
• 1997

This study measured the ignition limits of methane-air, propane-air, ethylene-air, and hydrogen-air mixture gases by discharge spark of D.C. power resistive circuit. The used experimental device is the IEC type spark ignition test apparatus, it consists of explosion chamber and supply -exhaust system of mixture gas. Mixture gases (methane-air, propane-air, ethylene-air, and hydrogen-air) were put into explosion chamber of IEC type spark ignition test apparatus, then it was confirmed whether ignition was made by 3,200 times of discharge spark between tungsten electrode and cadmium electrode. The ignition limits were found by increasing or decreasing the value of current. For the exact experiment, the ignition sensitivity was calibrated before and after the experiment in each condition. The ignition limits were found by changing the value of concentration of each gas-air mixture in D.C. 24 [V] resistive circuit. As the result of experiment, it was found that the minimum ignition limit currents exist at the value of methane-air 8.3 [$Vol\%$], propane-air 5.25[$Vol\%$], ethylene-air 7.8 [$Vol\%$], and hydrogen-air 21[$Vol\%$] mixture gases. For each the minimum ignition concentration of gases, the relationships between voltage and minimum ignition current were found. The results are as follows. - The minimum ignition limits are decreasing in the order of methane, propane, ethylene, and hydrogen. - The value of ignition current is inversely proportional to the value of source voltage. - The minimum ignition limit currents increase sharply at more than 2 [A]. The reason is caused by overheating the electrode.

• Analytical Science and Technology
• /
• v.23 no.1
• /
• pp.68-73
• /
• 2010

In order to develop the square wave voltammetric method determining cimetidine in an ampoule for injection, $5.00{\times}10^{-4}\;M$ cimetidine HCl solutions prepared with phosphate buffers of various pH values (3.01~8.97) were investigated by SWV. The well defined single peak due to the electrochemical reduction of -C=N-C$\equiv$N- in the structure of cimetidine moved towards the cathodic direction by -0.051V/pH as the pH values were increased indicating the involvement of hydrogen in its reduction. The calibration curves of cimetidine HCl in the concentration range between $1.00{\times}10^{-5}\;M$ and $5.00{\times}10^{-3}\;M$ prepared using three phosphate buffers yielded the slopes of 127,407nA/M (pH 3.01), 115,125nA/M (pH 5.00) and 111,287nA/M(pH 7.00) with excellent linearities of $R^2{\geqq}0.9997$. When one ampoule of Tagma Inj.$^{(R)}$ was analyzed by standard addition method by SWV, the within-day precision study (n=4) on the day of sample preparation resulted in the contents of cimetidine as $203{\pm}3.8\;mg$ (102% of the specified contents, RSD of 1.9%) and the inter-day precision (n=4) through 5 days was reasonable as 1.3% of RSD.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.2
• /
• pp.117-126
• /
• 2006

The Diurnal variation of galactic cosmic ray (GCR) flux intensity observed by the ground Neutron Monitor (NM) shows a sinusoidal pattern with the amplitude of $1{\sim}2%$ of daily mean. We carried out a statistical study on tendencies of the local times of GCR intensity daily maximum aad minimum. To test the influences of the solar activity and the location (cut-off rigidity) on the distribution in the local times of maximum and minimum GCR intensity, we have examined the data of 1996 (solar minimum) and 2000 (solar maximum) at the low-latitude Haleakala (latitude: 20.72 N, cut-off rigidity: 12.91 GeV) and the high-latitude Oulu (latitude: 65.05 N, cut-off rigidity: 0.81 GeV) NM stations. The most frequent local times of the GCR intensity daily maximum and minimum come later about $2{\sim}3$ hours in the solar activity maximum year 2000 than in the solar activity minimum you 1996. Oulu NM station whose cut-off rigidity is smaller has the most frequent local times of the GCR intensity maximum and minimum later by $2{\sim}3$ hours from those of Haleakala station. This feature is more evident at the solar maximum. The phase of the daily variation in GCR is dependent upon the interplanetary magnetic field varying with the solar activity and the cut-off rigidity varying with the geographic latitude.

• Korean Chemical Engineering Research
• /
• v.54 no.3
• /
• pp.305-309
• /
• 2016

Recently, there are many efforts focused on development of more economical non-fluorinated membranes for PEMFCs (Proton Exchange Membrane Fuel Cells). In this study, to test the durability of sPEEK MEA (Membrane and Electrode Assembly), ADT (Accelerated Degradation Test) of MEA degradation was done at the condition that membrane and electrode were degraded simultaneously. Before and after degradation, I-V polarization curve, hydrogen crossover, electrochemical surface area, membrane resistance and charge transfer resistance were measured. Although the permeability of hydrogen through sPEEK membrane was low, sPEEK membrane was weaker to radical evolved at low humidity and OCV condition than fluorinated membrane such as Nafion. Performance after MEA degradation for 144 hours and 271 hours were reduced by 15% and 65%, respectively. It was showed that the main cause of rapid decrease of performance after 144 hours was shorting due to Pt/C particles in the pinholes.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.57-62
• /
• 2011

The energy conversion efficiency of DSSCs (Dye-Sensitized Solar Cells) is dependent on the powder size, the structure, and the morphology of $TiO_2$ electrode. The higher efficiency is obtained with high surface area of the nanoanatase-$TiO_2$ powder adsorbed onto a lot more of the dye. Also, the enhancement of light scattering increases the efficiency with high adsorption of the dye. Powder size, crystalline phase, and shape of $TiO_2$ obtained by hydrothermal method have 15-20 nm, anatase and round. $TiO_2$ electrode has fabricated with the mixture of scattering $TiO_2$ particle with 0.4 ${\mu}m$ in nano-sized powder. Conversion efficiency of series of DSSCs was measured with volume fraction of scattering particle. Photovoltaic characteristics of DSSCs with 10% scattering particles are 3.51 mA for Jsc (short circuit current), 0.79 V for Voc(open circuit potential), filling factor 0.619 and 6.86% for efficiency. Jsc was improved by 11% and enhancement of efficiency by 0.77% compared with that of no scattering particles. The confinement of inserted light by light scattering particles has more increase of the injection of exiton(electron-hole pair) and decrease of moving path in electron. Efficiencies of DSSCs with more than 10% for scattering particles have reduced with increasing the pore in the $TiO_2$ electrode.