• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.6
• /
• pp.513-520
• /
• 2011

This paper presents the motion planning of robotic vehicles for the path tracking and the obstacle avoidance. To follow the given path, the vehicle moves through the turning radius obtained through the pure pursuit method, which is a geometric path tracking method. In this paper, we assume that the vehicle is equipped with a 2D laser scanner, allowing it to avoid obstacles within its sensing range. The turning radius for avoiding the obstacle, which is inversely proportional to the virtual force, is then calculated. Therefore, these two kinds of the turning radius are used to generate the steering angle for the front wheel of the vehicle. And the vehicle reduces the velocity when it meets the obstacle or the large steering angle using the potentials of obstacle points and the steering angle. Thus the motion planning of the vehicle is done by planning the steering angle for the front wheels and the velocity. Finally, the performance of the proposed method is tested through simulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.4
• /
• pp.359-364
• /
• 2012

Real-Time Traversability should be analyzed from the equiped sensors' data in real time for autonomous outdoor navigation. However, it is difficult to find out such traversability that considers the terrain roughness and the vehicle dynamics especially in case of skid type vehicle. The traversability based on real time dynamic analysis was proposed to solve such problem but in navigation with strait driving path. To adapt the method into the navigation with curved driving path, a path following controller should be incorporated into the dynamic model even though it cause the real time problem. In this paper, a dynamic model is proposed to solve the real time problem in the traversability analysis based on real time dynamic simualtion. The dynamic model contains the control dummy which is connected to the vehicle body with a universal joint to follow the curved path without controller. Simulation and experimental results on $6{\times}6$ articulated unmanned ground vehicle demonstrate the method's effectiveness and applicability into the traversability analysis on terrain with bumps.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.6
• /
• pp.434-445
• /
• 2021

This paper proposes an optimal design method for an unmanned underwater vehicle (UUV) platform to overcome strong current. First, to minimize the hydrodynamic drag components in water, the vehicle is designed to have a streamlined disc shape, which help maintaining horizontal motion (zero roll and pitch angles posture) while overcoming external current. To this end, four vertical thrusters are symmetrically mounted outside of the platform to stabilize the vehicle's horizontal motion. In the horizontal plane, four horizontal thrusters are symmetrically mounted outside of the disc, and each of them has the same forward and reverse thrust performances. With these four thrusters, a specific thrust vector control (TVC) method is proposed, and for external current in any direction, four horizontal thrusters are controlled to generate a vectored thrust force to encounter the current while minimizing the vehicle's rotation and maintaining its heading. However, for the numerical simulations, the vehicle's hydrodynamic coefficients related to the horizontal plane are derived based on both theoretical and empirically derived formulas. In addition to the simulation, experimental studies in both the water tank and circulating water channel are performed to verify the vehicle's various final performances, including its ability to overcome strong current.

• Journal of the Economic Geographical Society of Korea
• /
• v.24 no.3
• /
• pp.283-299
• /
• 2021

As the intelligent revolution triggered by digital technology, unmanned vehicles such as self-driving cars, robots, and drones appeared, which brought about innovative changes in the industry. Gyeonggi Local government has established both an ordinance and a basic plan regarding unmanned vehicles. It is time to prepare a data-based policy by understanding the current state of the unmanned vehicle industry in the province. As a result of the survey, the unmanned vehicle industry in Gyeonggi Province is 25% of the nationwide, and more than 88% is concentrated in the southern part of Gyeonggi Province. The land sector such as the robot and autonomous vehicles are focused on 71.4% and the aviation sector such as drones are 26.7%. However, unmanned vehicle companies in Gyeonggi-do are mostly small-sized businesses with less than 10 years of experience and are in the stage of introduction and growth level. They have a plan to improve technology through continuous R&D by hiring human resources. Therefore, Gyeonggi-do needs to consider policy support for sustainable growth of start-up and small enterprises and for fostering professional manpower and technical skills as well as for establishing an unmanned vehicle industry network to create, share, and spread knowledge.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.58-66
• /
• 2008

In the development of intelligent vehicles, path tracking of unmanned vehicle is a basis of autonomous driving and automatic navigation. It is very important to find the exact position of a vehicle for the path tracking, and it is possible to get the position information from GPS. However the information of GPS is not the current position but the past position because a vehicle is moving and GPS has a time delay. In this paper, therefore, the moving distance of a vehicle is estimated using a direction sensor and a velocity sensor to compensate the position error of GPS. In the steering control, optimal fuzzy rules for the path tracking can be found through the simulation of Simulink. Real driving experiments show the fuzzy rules are good for the steering control and the position error of GPS is well compensated by the proposed estimation method.

• The Journal of Korea Robotics Society
• /
• v.18 no.3
• /
• pp.299-307
• /
• 2023

In the midst of accelerating wars around the world, unmanned robot technology that can guarantee the safety of human life is emerging. ERP-42 is a modular platform that can be used according to the application. In the field of defense, it can be used for transporting supplies, reconnaissance and surveillance, and medical evacuation in conflict areas. Due to the nature of the military environment, atypical environments are predominant, and in such environments, the platform's path followability is an important part of mission performance. This paper focuses on reducing the minimum turning radius in terms of improving path followability. The minimum turning radius of the existing 2WS/2WD in-wheel platform was reduced by increasing the torque of the independent driving in-wheel motor on the rear wheel to generate oversteer. To determine the degree of oversteer, two GPS were attached to the center of the front and rear wheelbases and measured. A closed-loop speed control method was used to maintain a constant rotational speed of each wheel despite changes in load or torque.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.775-780
• /
• 2008

In this paper, unmanned driving of robotic vehicle using magnetic marker is proposed. One of the most important component of autonomous vehicle is to detect the position of a magnetic marker on the road. In order to calculate the precise position of a magnet embedded on the road, the relation of magnetic field and a sensor is analyzed, and a new position sensing system using arrayed magnetic sensor is proposed. Also, the steering control system using a stepping motor is developed for driving by automatic mode as well as manual mode. For the verification of usability, the developed robotic vehicle is tested on magnetic road.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.3 s.70
• /
• pp.7-14
• /
• 2006

This paper discusses the structural design and analysis of a 6,000 meters depth-rated capable deep-sea unmanned underwater vehicle (UUV) system. The UUV system is currently under development by Maritime and Ocean Engineering Research Institute(MOERI), Korea Ocean Research and Development Institute (KORDI). The UUV system is composed of three vehicles - a Remotely Operated Vehicle (ROV), an Autonomous Underwater Vehicle (AUV) and a Launcher - which include underwater equipment. The dry weight of the system exceeds 3 tons hence it is necessary to carry out the optimal design of structural system to ensure the minimum weight and sufficient space within the frame for the convenient use of the embedded equipments. In this paper, therefore, the structural design and analysis of the ROV and launcher frame system were carried out, using the optimizing process. The cylindrical pressure vessels for the ROV were designed to resist the extreme pressure of 600 bars, based on the finite element analysis. The collapse pressure for the cylindrical pressure vessels was also checked through a theoretical analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.3
• /
• pp.180-187
• /
• 2014

This paper introduces reliable multicast MAC protocol for cooperative unmanned vehicles. cooperative unmanned vehicles communicate with infrastructure and other unmanned vehicles in order to increase driving safety. They exchange information related to driving and thus it requires real-time and reliable multicast. However, the international vehicular communication standard, IEEE 802.11p WAVE, does not provide a reliable multicast scheme on the MAC layer. To address the problems of reliability, we propose a reliable multicast protocol called WiVCL, which avoids contention and collision. Our evaluation shows that the WiVCL achieves a high degree of reliability and real-time features.

• Journal of Navigation and Port Research
• /
• v.33 no.5
• /
• pp.303-308
• /
• 2009

Recently, unmanned systems have been studied and developed in various areas including aircrafts, automobiles and vessels. In addition, many researches about unmanned systems in Korea have been studying actively with the advancement of IT However, it is not satisfied with the result of the researches and developments. Bemuse of the reason we've here tried to make a very small USV which is a barge type. We applied the Great circle navigation calculation based on GPS to the autonomous navigation algorithm and used the LabVIEW 8.2 developed by NI corp. for programming The engine and rudder were controlled by pulse width modulation method. The engine system was composed of the DC motor and ESC(Electronic Speed Controller). It was also applied by the direct cooling system using DC motor pump. A very small USV was designed and made by ourself and it was verified the effectiveness of autonomous navigation algorithm through the tests at the sea.