• KIEAE Journal
• /
• v.13 no.6
• /
• pp.121-128
• /
• 2013

This study attempted to explore the MC design methods of modular construction using discontinuous double module grids and further, the design methods of walls. Modular construction is generally characterized with multiple units called modules with a module dimension of 3M(300mm) appearing in the form of double grids. The discontinuous double grids including correction values and gap values occurs inevitably in the modular construction where units are joined horizontally. Therefore, it is desirable to carry out the MC design taking into account these discontinuous double grids. In this study, the MC design was applied to the plane of wooden houses in modular construction, going through a process of setting the size of pillars and inside dimensions, of determining the dimension of discontinuous double grids that occur during the assembly of units, and of setting the dimension of outer walls in conjunction with the derived dimensions. The dimension of outer walls was applied differently depending on the range of regional use by analyzing the energy performance with the materials used. Consequently, the materials and components of factory-produced buildings can be used directly without processing, and the suitability of the outer wall design can be pre-determined by previewing the calculation of the cross-sectional configuration and heat transmission coefficients of outer walls in modular construction, allowing to be used as a decision-making tool of design.

• Korean Journal of Oriental Medicine
• /
• v.13 no.3
• /
• pp.105-110
• /
• 2007

This work reports the pulse diagnosis system using FBG sensors which can display pulse signals detected while oriental medical doctors are conducting pulse diagnoses and simultaneously pressing the sensors by three fingers. Each optical fiber has five FBG sensing units fabricated in 2 mm width and 2 mm inter-sensor spacing. Three optical fibers with the FBG units in the parallel line configuration are then placed on each finger-pressing region and thus overall 9 fibers are used for the pulse measurements on the so-called "chon", "gwan", and "ch대k". A fixture holding the optical fiber arrays is able to adjust the height of the FBG sensing units while placing the fibers on the wrist. The pulse signals detected by the FBG sensors from chon, kwan, and chuk have been analyzed using 4 channel spectrum analyzer connected to the optical fibers. The measured pulse signals exhibit variations due to the nonuniform pressure distributions applied. resulting in the differences in the detected pulse signals between fiber lines. However. this work is the first step towards objective and quantitative analyses of the pulse diagnosis in oriental medicine which has traditionally been performed on subjective basis. Future works will be devoted to improving sensor stability, developing the way applying pressure and algorithms reporting the objective classification of the pulse status from systemic measurements using the sensors instead of relying on the clinicians' diagnoses subjectively performed. A successful pulse diagnosis system emerging in the future is expected to contribute to education as well as promoting pulse diagnosis in oriental medicine to the scientific research area.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.19-25
• /
• 2002

Ternary $xSrO-yB_2O_3-0.1Al_2O_3$ and $xSrO-yB_2O_3-0.1SiO_2$ glasses were prepared as a function of R(${\equiv}x/y$). The fraction of four-coordinated brans ($N_4$), symmetric three-coordinated barons ($N_{3S}$), and asymmetric three-coordinated barons ($N_{3A}$) were determined quantitatively to study the structures of these glasses by $^{11}B$ NMR. The values of $Q_{cc}$ and ${\eta}$ for $BO_3$ unit in the glasses were 2.74MHz and 0.22, those for $BO_3{^-}$ unit were 2.54MHz and 0.55, and those for $BO_4$ unit 0.60~0.75MHz and 0.00, respectively. The structure of SrBAl glass at $R_{1st}$ consisted of tetraborate ($[B_8O_{13}]^{-2}$) units and 1st-modified diborate ($[B_2Al_2O_7]^{-2}$) units, and those for the glass at $R_{max}$consisted of diborate ($[B_4O_7]^{-2}$) units, metaborate ($[BO_2^{-1}]$), 1st-modified diborate units, and 2nd-modified diborate ($[B_2Al_2O_8]^{-4}$) units. Due to the oxygens introduced from the strontium oxide. $AlO_4$ units were preferably formed rather than $BO_4$ units. And, the structure of SrBSi glasses in the region $R{\leq}0.5$ could be viewed as binary $SrO-B_2O_3$ glasses structure diluted by silicate oxide: therefore, the Si atoms of the glasses did not contributed to the change the configuration around the boron atoms. The silicate oxide was formed the $SiO_4{^-}$ units rather than the $BO_3{^-}$ units by the oxygens introduced from the storntium oxide in the region of $R{\geq}R_{max}$, and structure of those glass at $R_{max}$ consisted of diborate units, metaborate units loose $BO_4([BO_2]^{-1})$, and $SiO_4{^-}([SiO_{2.5}]^{-1})$ units.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.101-108
• /
• 2011

In this paper we present the specification development for the localization of interlockings which control routes within a HSR station yard. For the electronic interlockings in Korea introduced from France in the 1990s, it has a complicated hardware configuration and communication protocols in order to secure safety. Now 30 years later, in case of the application of the up-to-date IT technology, it is expected to achieve equal or greater safety and save maintenance costs. Additionally, we develop the specification so as to utilize the stable domestic electronic interlocking technology for general railways, beyond the simple maintenance for the performance maintenance of foreign devices, to high-speed railways. Therefore, we perform a study for the localization of the HSR electronic interlockings by comparing and analyzing interlocking logic units between conventional HSR and general railways.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.554-557
• /
• 2013

This letter presents a power amplifier (PA) with an on-chip power detector for 2.4-GHz wireless local area network application. The power detector consists of a clamp circuit, a diode detector, and a coupled line directional coupler. A series inductor for an output matching network in the PA is combined with a through line of the coupler, which reduces the coupling level. Therefore, the coupler employs a metamaterial-based transformer configuration to increase coupling. The amount of coupling is increased by 2.5 dB in the 1:1 symmetric transformer structure and by 4.5 dB from two metamaterial units along the coupled line.

• Journal of the military operations research society of Korea
• /
• v.2 no.1
• /
• pp.185-194
• /
• 1976

A terminal response time analysis for a general class of terminals-to-computer subsystem is presented in this paper. On the point of the front view, it should be considered for R.O.K. Military Defense to set up the communication network in order to facilitate for the currency of the information and the data communication system. The model used to study is based on the advanced data communications system in which terminals are connected to Terminal Control Units(TCU) that are in turn connected to local Front-End Processor(FEP). The line control procedures used to interface a TCU and an FEP may be half-duplex Binary Synchronous Communication(BSC), half-duplex Synchronous Data Link Control(SDLC), or full-duplex SLDC. This paper will contribute to facilitate the initial phase of system design and configuration for the Military Defense Communication Network System in future.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.324-326
• /
• 2009

We present the design of a compact microstrip lowpass filter with a wide stopband which is up to ten times the cutoff frequency. The filter is based on a coupled-line configuration and shunt open stubs. The open stubs create additional transmission zeros, which are used to extend the stopband of the filter without any additional components or cascaded units. A prototype lowpass filter with a 3 dB cutoff frequency of 0.428 GHz and a 15 dB stopband extended up to 4.77 GHz is fabricated to validate the theoretical predictions.

• Journal of the Korean Chemical Society
• /
• v.16 no.1
• /
• pp.6-12
• /
• 1972

The crystal structure of monoethanolamine hydrochloride is triclinic P1 with two formula units in a cell of dimensions a = $4.42\pm0.02$, b = $7.44\pm0.02$, c = $7.48\pm0.02$, $\alpha$ = $102.4\pm0.3$, $\beta$ = $91.1\pm0.3$, $\gamma$ = $77.2\pm0.3^{\circ}.$ The configuration of monoethanolamine is a gauche form with dihedral angle, $90^{\circ}$. The nitrogen atom forms four hydrogen bonds, three to Cl- ions(3.15, 3.24, $3.28\AA)$ and one to a hydroxyl group of another molecule (N${\cdot}{\cdot}{\cdot}$O, $2.90{\AA})$. The oxygen also forms two such bonds, one to a Cl- ion $(3.14\AA)$, one to an amine group of another molecule (O${\cdot}{\cdot}{\cdot}$N, $2.90{\AA}).$ Molecules are linked into two-dimensional network by hydrogen bonds.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.8
• /
• pp.710-720
• /
• 2016

The Floating Wave Energy Convertor (FWEC) mooring design has an important requirement associated with the fact that, for a wave energy converter, the mooring connections may interact with their oscillations, possibly modifying its energy absorption significantly. It is therefore important to investigate what might be the most suitable mooring design according to the converter specifications and take into account the demands placed on the moorings in order to assure their survivability. The objective of this study is to identify a computational fluid dynamics method for investigating the effects of coupling a wave energy device with a mooring system. Using the commercial software ANSYS AQWA and ANSYS FLUENT, a configuration was studied for different displacements from the equilibrium position, load demands on the moorings, and internal fluid motion. These results and findings form a basis for future efforts in computational model development, design refinement, and investigation of station keeping for FWEC units.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.216-218
• /
• 1995

This paper presents the concepts developed to propose Distributed Control System(DCS). To achieve adequate satisfaction under various conditions, the DCS should be designed from two points of view of functions distributions and performance planning. Performance evaluation criteria can be specified by the response time between units and the utilization of each unit. One has to also consider the ease and the cost of installation, maintenance, repair. Based on these characteristics, different system configuration can be evaluated and compared through results about evaluation criteria in order lo select the best DCS for particular process. The results, in abbreviated form, of the simulation DCS controlling a CAL(Continuos Annealing Line) plant of iron process ate presented.