• Journal of Wetlands Research
• /
• v.18 no.3
• /
• pp.275-281
• /
• 2016

This study was conducted to analyze the runoff characteristics of the highway depending on the number of vehicles and to provide the installation proposal of an NPS pollution reduction facility. There were a total of 5 monitoring sites used for the study namely, Gyeongbu, Seohaean, Honam and Tongyeoung Dageon highway. Monitoring events started from 2006 until 2015 having a total of 44 storm events. According to monitoring statistics, the average antecedent dry days (ADD) and rainfall was 6.2 days and 19.2 mm, respectively. The Gyeongbu Highway (H-4) was recorded having the highest Average Daily Traffic and Catchment Area (ADT/CA) with $49.4car/day{\cdot}m^2$ while other site were less than $10car/day{\cdot}m^2$. The average concentration of the NPS pollutants generated from monitoring sites were 63.5 mg/L(TSS), 24.9 mg/L(BOD), 3.35 mg/L(TN), 0.63 mg/L(TP) and 298 ug/L(Total Zn). This exhibited lower values in comparison to the remarks of highway related runoff EMC values published in Korea. Moreover, through the results of the correlation analysis between the contaminant concentration and ADT/CA, $R^2$ value of SS showed the highest correlation with 585. Through the correlation equation between ADT/CA and EMC of TSS, when there is 73.7 mg/L of TSS EMC found from a domestic highway, ADT/CA ratio is normally $13car/day{\cdot}m^2$. Therefore, in a case of more than 13 cars passing through a certain area, the area can be considered and present as the point of generation of nonpoint source pollutants. Also, in this study, since it considered a unit area ADT indicated in previous studies, it was determined that it has a high applicability and utilization in generalized units than conventional study which were conventionally done.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.9 no.2
• /
• pp.162-168
• /
• 2006

Purpose: Microbial colonization of the intestine begins just after birth and development of the normal flora is a gradual process. The first bacteria colonizing the intestine in newborns are Staphylococcus, Enterobacteriaceae and Streptococcus. For several days after birth, the number of Bifidobacterium spp. increase. The aim of this study was to investigate the changes of microflora for seven days postnatally in neonatal stool. Methods: Fifteen neonates (breast : formula : mixed feeding 1 : 8 : 6, vaginal delivery : cesarean section 3 : 12) who were born at the Kangdong Sacred Heart Hospital, Hallym University were enrolled. First meconium and stools of postnatal 1-, 3-, and 7-day were innoculated. Blood agar plates for total aerobes, trypton bile X-glucuronide agar for E. coli, phenylethyl alcohol agar for gram positive anaerobes, MRS agar for Lactobacillus spp., bifidobacterium selective agar for Bifidobacterium spp. and cefoxitin-cycloserine-fructose agar for Clostridium difficile were used in the general incubator ($CO_2$ free incubator), $CO_2$ incubator or the anaerobic chamber for 48 or 72 hours at $37^{\circ}C$ and then colony forming units were counted. Results: No microflora was identified in the first meconium. Total aerobes, E. coli, and gram positive anaerobes were significantly increased with advancing postnatal days. In only one baby, Lactobacillus acidophilus was detected $2{\times}10^5CFU/g$ in the seven-day stool. Bifidobacterium spp. was detected in two babies. Clostridium difficile was not detected during the seven days. There were no significant differences in the bowel flora depending on the delivery pattern and feeding method. Conclusion: This study shows many changes in the intestinal normal flora in neonatal stool during seven days postnatally. If these findings are confirmed with larger studies, the data may be preliminary findings to support use of probiotics in neonates.

• Economic and Environmental Geology
• /
• v.18 no.4
• /
• pp.399-410
• /
• 1985

Bentonites from the Janggi Group of the Lower Miocene age from the Geumgwangdong area, Korea, have been studied for mineralogical and genetic characterization. The Janggi Group is subdivided, in ascending order, into the Janggi Conglomerate, the Nuldaeri Tuff, the Geumgwangdong Shale, the Lower Coal-bearing Formation, the Basaltic Tuff, and the Upper Coalbearing Formation. Bentonites occur as thin or thick beds in all sedimentary units of the Janggi Group, except for the Janggi Conglomerate. Significant bentonite deposits are found in the Nuldaeri Tuff, the Lower Coal-bearing Formation and the Basaltic Tuff. Bentonites consist mainly of smectite (mainly montmorillonite), with minor quartz, cristobalite, opal-CT and feldspar. Occasionally, kaolinite, clinoptilolite or gypsum is associated with bentonites. Bentonites were studied by the methods of petrographic microscopy, X-ray diffraction, thermal analysis (DT A and TG), infrared absorption spectroscopic analysis, SEM, intercalation reaction, and chemical analysis. Smectites commonly occur as irregular boxwork-like masses with characteristic curled thin edges, but occasionally as smoothly curved to nearly flat thin flakes. Most of smectites have layer charge of 0.25-0.42, indicating typical montmorillonite. Crystal-chemical relations suggest that Fe is the dominant substituent for Al in the octahedral layer and there are generally no significant substituents for Si in the tetrahedral layer. Ca is the dominant interlayer cation in montmorillonite. Therefore, montmorillonite from the study area is dioctahedral Ca-montmorillonite. Occurrence and fabrics of bentonites suggest that smectites as well as cristobalite, opal-CT and zeolites have been formed diagenetically from tuffaceous materials. The precursor of smectites is trachytic or basaltic tuff. Smectites derived from the former contain relatively more $Al_2O$ a and less $Fe_2O_3$ than those from the latter.

• Economic and Environmental Geology
• /
• v.43 no.1
• /
• pp.53-66
• /
• 2010

We report petrologic characteristics including $^{40}Ar-^{39}Ar$ absolute ages of the subsurface lavas recovered from borehole cores in two islets, Marado and Gapado, off the southwestern coast of Jeju in southernmost Korea and discuss on the volcanism in the region. The lavas in Gapado are apparently divided into one unit with bright colored, aphanitic texture and sheet jointed, and another unit with dark colored and massive. The outcrops often show differentially weathered pattern due to textural difference. While, the lavas in Marado have vesicular and glomerporphyric texture, even though each lava flow unit in Marado has slight unique texture with variation of vesicularity and phenocrysts. The chemical composition of rock core samples from Gapa borehole and Mara borehole shows that the lavas from Gapado and Marado are classified into basaltic trachyandesite($SiO_2$ 52.6-53.6 wt%, $Na_2O+K_2O$ 7.3-7.5 wt%) and tholeiitic andesite($SiO_2$ 51.7-52.8 wt%, $Na_2O+K_2O$ 3.6-4.1 wt%), respectively. The measured $^{40}Ar-^{39}Ar$ plateau ages range from $824{\pm}32\;Ka$(MSL -69 m) to $758{\pm}\;Ka$(MSL 19 m) for core samples of Gapa borehole and $259{\pm}168\;Ka$(MSL -26 m) for a core sample of Mara borehole, respectively. The absolute age of Gapado basaltic trachyandesite is well correlated with that of Sanbangsan trachyte(Won et al., 1986). Meanwhile, the age of a sample in Marado has $259{\pm}168\;Ka$(MSL -26 m) with poor plateau age formation and high error range. We report the data in caution but the rock composition and absolute age of Marado tholeiitic andesite are relatively correlated with those of lava units from Duksu and Sangmo-2 boreholes, indicating the volcanism during 260-150 Ka. On the basis of interpretation of occurrences of exposed and subsurface volcanic rocks of the study area, stratigraphic relationship with adjacent borehole cores and the bathymetry chart of surrounding area, it indicates that the lavas in Gapado were formed around 800 Ka during relatively early stage of volcanic activity in Jeju Island. Meanwhile, Marado may have originated around 260-150 Ka during relatively young stage of volcanism in Jeju Island. It is inferred that the volcanisms have originated in land and these islets were individual ancient volcanoes. The apparent topography has been re-shaped by tidal erosion due to transgression.

• Journal of Hospice and Palliative Care
• /
• v.10 no.2
• /
• pp.78-84
• /
• 2007

Purpose: The prevalence of lung cancer is increasing continuously these days. We studied clinical characters of the terminal lung cancer patients who had died in hospice units and our study is the basic report for efficient hospice and palliative care to the lung cancer patients. Methods: We retrospectively reviewed the medical records of 129 terminal lung cancer patients who had died in Sam Anyang Hospice Unit from March 2003 to December 2006. The survival days during the hospice and palliative care were analyzed using Kaplan-Meier method of SPSS 13.0. Results: There were 93 males (72%) and 36 females (28%), and median age of patients was 68 years (range $37{\sim}93$). Eighty two patients (64%) took analgesics, the others 47 (36%) not. The most prevalent reason for admission was dyspnea (47 patients, 36%) and it was different from the terminally ill cancer patients being hospitalized because of pain. And the most common symptom was general weakness (103 patients, 80%). One hundred twenty of the paitents (93%) were administered opioid analgesics, and IV morphine shots were mostly used (103 patients, 80%). Sedation was used in 87 patients (67%), and midazolam was mostly used (68 patients, 53%). The median survival in hospice and palliative care was 35 days and the median hospitalization was 24 days. Conclusion: It is very important to manage dyspnea in terminal lung cancer patients. The length of hospice and palliative care for the terminal lung cancer patients is still short. Therefore continuous education and promotion of hospice and palliative care is needed for an effective care for the patients, their families and doctors.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.254-266
• /
• 1997

This study was to know the usefulness of argon laser for composite resin, to prove the polymerized effect of heat treatment of composite resin inlay and to get the curing method for optimal physical properties of composite resin inlay. In this study we used four light curing units and one heat curing unit: Visilux $II^{TM}$, a visible light gun: $SPECTRUM^{TM}$, an argon laser: Unilux AC$^{(R)}$ and Astorn XL$^{(R)}$, visible light curing unit: CRC-$100^{TM}$ for heat treatment. Compared to a control group, we divided the experemental groups into five as follows: Control group: Light curing(Visilux $II^{TM}$) Experimental group 1 : Light curing(Visilux $II^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 2: Light curing(Visilux $II^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment(CRC-$100^{TM}$) Experimental group 3 : Laser curing($SPECTRUM^{TM}$) Experimental group 4 : Laser curing($SPECTRUM^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 5 : Laser curing($SPECTRUM^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment (CRC-$100^{TM}$) According to the above classification, we made samples through the curing of Clearfil CR Inlay$^{(R)}$, which is a composite resin for inlay, in a separable cylindrical metal mold and polycarbonate plate. And then, we measured and compared the value of compressive strength, diametral tensile strength and the surface micro hardness of each sample. The results were as follows : 1. Among the experimental groups, group 5 showed the highest value of compressive strength, $157.50{\pm}10.24$ kgf and control group showed the lowest value of compressive strength, $103.93{\pm}21.93$ kgf. Control group showed significant difference with the experimental groups(p<0.001). Group 2 which was treated by the heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was significant difference group 4 and group 5(p<0.001). 2. Among the experimental groups, group 5 showed the highest value of diametral tensile strength, $95.84{\pm}1.97$ kgf and control group showed the lowest value of diametral tensile strength, $81.80{\pm}2.17$ kgf. Control group which was cured by visible light showed higher diametral tensile strength than group 3 which was cured Argon Laser. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 3. Among the experimental groups, group 5 showed the highest value of microhardness of top surface, $148.42{\pm}9.57$ kgf and control group showed the lowest value of microhardness, $111.43{\pm}7.63$ kgf. In the case of bottom surface, group 5 showed the highest value of $146.19{\pm}7.62$ kgf, and control group showed the lowest, $104.03{\pm}11.05$ kgf. Group 3 which was cured by Argon Laser showed higher diametral tensile strength than control group which was cured only with a visible light gun. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was a significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 4. According to the above results, we took a conclusion that argon laser can be used as a useful unit for curing the composite resin and heat treatment can improve the physical properties of the composite resin inlay.

• Journal of Animal Science and Technology
• /
• v.45 no.5
• /
• pp.767-776
• /
• 2003

An experiment was conducted to investigate the effects of dietary herbal product(Miracle$^{\circledR}$) supplementation on the performance, nutrient digestibility, fecal microflora and blood parameters in pigs. Forty eight cross bred(Y${\times}$L${\times}$D) weanling pigs (average initial body weight 7.84kg${\pm}$0.17, 28 d old) were used in 35 d feeding trial. Pigs were allotted to 16 raised floor cages(W 35.5cm${\times}$L45cm${\times}$H 55cm). Each treatment had four replications of 3 pigs each. Treatments were: control (T1), CTC 100ppm (T2), Miracle$^{\circledR}$ 0.15% (T3) and CTC 100ppm + Miracle$^{\circledR}$ 0.15% (T4). The herbal product supplementation(T3) tended to improve the weight gain, feed intake, feed/gain but there were no significant differences among treatments. Nutrient digestibility was significantly(P〈0.05) affected by dietary treatments. The pigs fed T3 diet showed the lowest digestibility of DM, crude protein, NFE, P, and amino acids among treatments. Serum cholesterol level of pigs fed T3 diet was lowest and significantly(P〈0.05) lower than those fed antibiotic supplemented diet(T2). Triglyceride and HDL level of the pigs fed T3 diet were also lower than those of others but the differences were not significant. The level of serum IgG was significantly(P〈0.05) different among treatments. The level of serum IgG was highest in T4, followed by T1, T2 and T3. Serum AST(Aspartate aminotransferase) level of the control(T1) was lower than other treatments. Levels of serum total protein, albumin and ALT(Alanine aminotransferase) were not significantly different among treatments. The colony forming units (CFU) of Lactobacillus, Cl. perfringens and E.coli in feces were not significantly different among treatments but those of Cl. perfringens of T2 (CTC 100ppm) showed the lowest count at both 3rd and 5th wk. It is concluded that herbal product Miracle$^{\circledR}$ does not significantly affect growth performance of weanling pigs but it influenced the digestibility, serum IgG, cholesterol and AST level. The combination of the herbal product Miracle$^{\circledR}$ with antibiotic(CTC) showed no synergistic effects.

• Journal of Biomedical Engineering Research
• /
• v.16 no.4
• /
• pp.463-470
• /
• 1995

Complete prelining of artificial vascular grafts with autologous endothelial cells may be one of the ideal solutions to obtain a nonthrombogenlc blood-contacting surface. To establish an intact endothelial cell monolayer on a prosthetic surface at the time of implantation,a sufficient number of endothelial cells and adequate propagation condition In cell culture are prerequisites. In this experimental study, endothelial cells from microvessels of adult human oriental adipose tissue were enzymatically harvested, and optimal culture conditions for proliferation of the endothelial cells in cell culture were examined. Human oriental adipose tissue was digested with collagenase and endothelial cells were separated from other stromal elements by mesh filtration method. Cultured cells were identified as endothelial cells by immunofluorescent staining for factor VIII-related antigen. Proliferation in usual 20% fetal bovine serum (FBS) medium or medium containing endothelial cell growth factor (ECGF)(5 ng/ml) and heparin (HEP)(1,000 units/ml) were compared,and the effects of adding compounds that increase intracellular cyclic adenosine monophosphate levels, that is,cholera toxin (CT)(1 $\mu\textrm{g}$/ml) and isobutylmethylxanthine (IBMX)(0.2 ml),were also analyzed. In total,following eight media groups were examined. 1) FBS medium + ECGF + HEP, 2) FBS medium + ECGF + HEP+CT, 3) FBS medium+ECGF+HEP+lBMX, 4) FBS medium+ECGF+HEP+CT+ IBMX, 5) FBSmedium, 6) FBS medium +CT, 7) FBS medium + IBMX, 8) FBS medium + CT + IBMX. It was shown that the medium containing ECGF + HEP with or without cholera toxin was most efficient in Stimulating cell proliferation. IBMX was considered to have antagonistic effect to ECGF. Among experimental groups without ECGF and HEP, the addition of cholera toxin and IBMX was shown to significantly potentiate cell proliferation. This results could provide a practical method for use of cultured human endothelial cells for endothelial cell seeding of cardiovascular prosthetic device, particularly in small-diameter vascular grafts.

• Korean Journal of Food Science and Technology
• /
• v.27 no.5
• /
• pp.716-723
• /
• 1995

The fucoidan purified from Korean brown seaweed, Ecklonia stolonifera was characterized on molecular structure and blood anticoagulant activities. Extraction was conducted at $100^{\circ}C$ with water and repeated twice. The crude fucodian was 151.1g out of 20.0 kg of Ecklonia stolonifera. The Fucoidan-1, which was purified from crude fucoidan using calcium chloride and cetyl pyridium chloride (CPC), was 35.2% against crude fucoidan. Fucoidan-5 was obtained approximately 28.1% from Fucoidan-1 through DEAE-Toyopearl 650 M ion-exchange column chromatography and showed one band by cellulose acetate electrophoresis. The molecular weight of Fucoidan-5 was estimated to be about 21,000∼23,000 dalton by Sephacryl S-300 gel filtration chromatography. Fucoidan-5 consists of 35.7% of fucose and 4.3% of galactose and the molar ratio of fucose and sulfate was about one to one. IR spectrum of Fucoidan-5 showed absorption at $1240\;cm^{-1}\;and\;850\;cm^{-1}$ and specific rotation value, $[\alpha]$, was $[\alpha]$. These results suggests that the sulfate maybe bind at $C_{4}$ carbon on ${\alpha}-L-fucose$. Gas chromatograph of methyl alditol acetate revealed that Fucoidan-5 is a fucose containing sulfated polysaccharide with $({\alpha}l-2)\;or\;({\alpha}l-2)$ glycosidic linkage. Anti-thrombin activity of the Fucoidan-5 was estimated as 1.4 time stronger than heparin. From above results, the purification methods using CPC and ion exchange chromatography is effective tools for obtaining highly purified fucoidan from Gompi, Ecklonia stolonifera.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.32 no.4
• /
• pp.634-643
• /
• 2005

The aim of this study is to evaluate the effects of blue light emitting diode (LED) Light Curing Units (FreeLight 2, L.E.Demetron I, Ultra-Lume 5) on the microhardness of three resin composites (Z250, Point 4, Dyract AP) and to determine their optimal curing time. Samples were made using acrylic molds $(2.0mm{\times}3mm)$ of each composite. All samples were prepared over a Mylar strip placed on a flat glass surface. After composite placement on the molds, the top surface was covered with another Mylar strip and a glass slab was gently pressed over it. The times of irradiation were as follows: Elipar TriLight, 40 s; Elipar FreeLight 2. L.E.Demetron I, and Ultra-Lume 5, 10s, 20s, 40s, respectively. Mean hardness values were calculated at the top and bottom for each group. ANOVA and Sheffe's test were used to evaluate the statistical significance of the results. Results showed that FreeLight 2, Ultra-Lume 5, and L.E.Demetron I were able to polymerize point 4 in 20 seconds to a degree equal to that of the halogen control at 40 seconds. FreeLight 2 and L.E.Demetron I were able to polymerize Z250 in 10 seconds to a degree equal to that of the halogen control at 20 seconds. FreeLight 2 and L.E.Demetron I were able to polymerize Dyract AP in 10 seconds to a degree equal to that of the halogen control at 40 seconds. The commercially available LED curing lights used in this study showed an adequate microhardness with less than half of the exposure time of a halogen curing unit.