• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2006년도 추계학술대회 논문집
• /
• pp.125-130
• /
• 2006

The characteristics of boiling heat transfer and critical heat flux (CHF) behavior of nano-fluids were studied by using various sized silver and alumina nanoparticles. The diameter of nanoparticles was from 2 nm to 250 nm for silver and from 20nm to 40nm for alumina. Pool boiling characteristics and CHF enhancement of nano-fluids with different sized nanoparticles were compared with those of pure water and each nano-fluids. The experiment was performed at atmospheric pressure and the temperature of the pool was maintained constantly by using a flat immersed heater. The concentration of nano-fluids was uniform in all experiments as 0.01g/liter. The results showed that the measured boiling curves were shifted to the right. It demonstrated that the occurrence of nucleate boiling regime in nano-fluids retarded, compared with that of pure water. Also, in nano-fluids, the boiling curves showed that CHF of nano-fluids is significantly enhanced and represented the effect of particle size on boiling characteristics.

• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.179-184
• /
• 2004

In this work, a copper-clad aluminum composite was fabricated using hot hydrostatic extrusion with various extrusion ratios (8.5, 19, 49) and semi-die angles (30, 45, 60 degree) at a temperature of 32$0^{\circ}C$, Material characteristics of copper-clad aluminum composites were determined from compression tests and hardness tests The results showed that for ER of 8.5, the optimum semi-die angle was below or equal to 30 degree and a pressure drop was about 31%. For ER of 19, the optimum semi-die angle was in the range of 40 to 50 degree and a pressure drop was about 38%. In the case of ER=49, the optimum semi-die angle was above or equal to 60 degree and a pressure drop was about 36%. Compressive yield strength was maximum for ER of 8.5 and semi-die angle of 30 degree and the value of maximum was 155 MPa. Uniform hardness distribution was obtained as the extrusion ratio increases and the semi-die angle decreases. In the case of ER=8.5 and semi-die angle of 30 degree, the lowest extrusion pressure and the maximum compressive yield strength was obtained. Therefor, it was concluded that the optimum extrusion condition for fabricated copper-clad aluminum composites under hydrostatic pressure environment was ER of 19 and semi-die angle of 30 degree.

• 열처리공학회지
• /
• 제8권1호
• /
• pp.44-52
• /
• 1995

The specimen for laser hardening have been carried out using SM45C which is coated with black paint or graphite for better absorption. Segmented mirror was used in order to produce a square beam ($10{\times}10mm$) at the surface with a homegeneous intensity distribution across the beam. $CO_2$-Laser power was changed from 2kW to 4kW and transfer velocity was varied from 0.1m/min to 2.0m/min. The maximum hardness and case depth of SM45C steel are 790Hv and 1.5mm by laser hardening. When the surface of specimens was melted during laser hardening. the surface hardness of SM45C steel was decreased. The surface hardness of 2 layer coated specimen(black paint: $15.4{\mu}m$, graphite coating: $9.5{\mu}m$) was increased than that of 1 layer coated specimen. It is desirable to prepare 2 or more coating layer on the steel surface in order to sufficient case depth and hardness in laser hardening. The graphite coating on the specimen surface was obtained more uniform temperature distribution than black paint coating in laser hardening process.

• 수산해양기술연구
• /
• 제30권1호
• /
• pp.45-52
• /
• 1994

The study was conducted to evaluate reliability of the longitudinal tensile properties of unidirectional carbon fiber reinforced composites. Two kinds of carbon fiber reinforced composites laminates were tested in order to examine the factors of variability and have the information concerning reliability improvement. Temperature dependence of the strength and its variability were investigated by means of testing at two kinds of temperatures. Statistical distributions of the respective mechanical properties were obtained from the tensile tests. As a result, strength of composites was directly proportional to the ultimate strain and was not proportional to the elastic modulus. The fracture behavior in bending of notched plate was studied for a composite material. The uniform bending tests of notched plates have been carried out for a wide range of notch radii. The experiment shows that the nominal stress at failure decreased with decreasing notch radius and it approaches a constant value when the notch radius is less than about 0.3mm. The critical maximum stress is governed by notch root radius alone in the case of a constant thickness of specimen.

• 수산해양기술연구
• /
• 제31권3호
• /
• pp.296-305
• /
• 1995

보일러 및 연소로 등에서의 부유체 환경에서 입자와 벽면 사이의 열전달 현상을 규명하기 위한 수치적인 모델링을 행하였다. 본 연구에서는 벽면에 수직 충돌하는 입자에 의한 열전달 현상을 알아보기 위해 2차원 모델을 사용하였다. 입자표면에서 단열된 경계조건과 등온의 경계조건을 사용한 결과를 비교함으로써, 입자가 벽면에 충돌할 때 유체를 매개로한 전도와 입자에 의해 야기된 대류 현상을 비교할 수 있었다. 계산 결과, 입자가 벽면에 충돌하기 직전에는 입자 크기의 반정도의 거리에 도달할 때까지는 입자의 영향이 별로 없고, 충돌하고 난 후에 영향이 많았다. 또한, Pe 수가 작을 때는 유체를 매개로 한 전도가 지배적이며, Pe 수가 증가할수록 야기된 대류의 효과가 점차 증가하였다

• 한국식품조리과학회지
• /
• 제19권4호
• /
• pp.521-528
• /
• 2003

This research was conducted to find the effects of the addition of kugija to the quality and conservativeness of Nabak kimchi. Kugija extract was prepared by boiling kugija fruits, at different ratios (1, 3, 5 and 7%; w/v) in water for 30 minutes. The changes in the sensory and microbiological properties of the Nabak kimchi were measured for 25 days, following the preparation at a uniform temperature of 10$^{\circ}C$, and compared to a control (distilled water without kugija). For the properties of acceptability, the Nabak kimchi treated with 3% kugija was evaluated as being best during the whole fermentation. The number of total cell counts and number of lactic acid microorganisms gradually increased to a maximum, and then decreased. It was the maximum for controlling and 1 % treatment on day 2, forand 3, 5 and 7% treatment on day 7. (Eds note: the highlighted sentence needs c1arification\ulcorner)This experimental study revealed the effect of kugija extract in enhancing the eating qualities on Nabak kimchi and retarding the fermentation over the initial seven days. The optimum levels of kugija extract on Nabak kimchi obtained through experiments was between 1 and 3% of the water content. Although 3% gave a better color, the fermentation-retarding effect and savory taste. The application of kugija extract could be domestically applied to improve the eating quality and the preservation of traditionally prepared Nabak kimchi.

• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.4711-4717
• /
• 2011

PVD방식에 의한 TiN박막의 형성은 DC와 RF sputtering deposition 방식을 적용할 수 있지만, 플라즈마 생성을 위해 주입된 가스의 이온화율이 떨어져 박막성형 속도가 느려지며, 박막과의 접착력을 높이는 것에도 한계성을 가지고 있다. 이를 개선하기 위해 증착과 동시에 이온빔을 조사하는 이온빔 진공증착 IBAD(Ion beam assisted deposition)를 이용 하게 되면, 코팅 전에 소재 표면을 Ion beam으로 조사하기 때문에 표면cleaning의 효과가 크고, 접착력이 높은 박막을 얻을 수 있다. 또한 고 진공과 낮은 온도에서도 균일한 두께의 고순도의 박막을 얻을 수 있는 이점이 있다.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.279-301
• /
• 2017

Thermo-mechanical vibration characteristics of in homogeneousporous functionally graded (FG) micro/nanobeam subjected to various types of thermal loadings are investigated in the present paper based on modified couple stress theory with consideration of the exact position of neutral axis. The FG micro/nanobeam is modeled via a refined hyperbolic beam theory in which shear deformation effect is verified needless of shear correction factor. A modified power-law distribution which contains porosity volume fraction is used to describe the graded material properties of FG micro/nanobeam. Temperature field has uniform, linear and nonlinear distributions across the thickness. The governing equations and the related boundary conditions are derived by Extended Hamilton's principle and they are solved applying an analytical solution which satisfies various boundary conditions. A comparison study is performed to verify the present formulation with the known data in the literature and a good agreement is observed. The parametric study covered in this paper includes several parameters such as thermal loadings, porosity volume fraction, power-law exponents, slenderness ratio, scale parameter and various boundary conditions on natural frequencies of porous FG micro/nanobeams in detail.

• 한국태양에너지학회 논문집
• /
• 제34권3호
• /
• pp.49-56
• /
• 2014

A fiat-plate or vacuum tube solar collector have been mainly used for hot water supply of house because of some being difficult to get uniform energy density, so little applied into industrial field. This study is to apply the PTC(parabolic trough collector) solar collector into industrial field such as sludge dewatering system for energy reduction. The real scale system which composed of PTC Solar Collector and Thermal Dewatering (TDW) is established. PTC solar collector is designed to produce a hot water with $80^{\circ}C$ of temperature. And size of TDW is $630{\times}630mm$. Hot water produced from PTC solar collector is supplied into heating plate of TDW, and sludge like waterworks or wastewater is dewatered. PTC solar collector with $10m^2$ of area produce energy of average 5,618 kcal. As according to results from real scale performance, solar collector takes charge 94 % of the amount that TDW consume energy which is so large part if compare with boiler. It means that PTC solar collector is useful to apply industrial field under the condition of sufficient solar radiation. And it is analyzed that TDW by PTC solar collector has an economical validity.

• 한국광학회지
• /
• 제16권5호
• /
• pp.406-410
• /
• 2005

처프된 광섬유 브라그 격자를 사용하여 발진모드 수를 조절할 수 있는 외부 공진기 레이저를 제안하였다. 광섬유 브라그 격자에 인가되는 선형적인 온도차를 변화시킴으로써 광섬유 브라그 격자의 반사 대역폭을 조절할 수 있었으며 이러한 격자를 외부 공진기 레이저의 외부 반사경으로 사용하여 발진모드 수를 단일모드에서 세 개의 모드까지 조절할 수 있었다.