• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.229-234
• /
• 2005

Following the recent trend in the automotive manufacturing technologies, the product design subject to the die casting becomes more and more complex. The requirement of the die design becomes more demanding than ever before. In some cases the product's shape can have multiple slender manifolds. In such cases, design of the inlet and outlet parts of the die is very important in the whole manufacturing process. The main issues required for the qualified products are to attain gentle and uniform flow of the molten liquid within the passages of the die. To satisfy such issues, the inlet cylinder ('bed cylinder' in this paper) must be as large as possible and simultaneously the outlet opening at the end of each passage must be as small as possible. However these in turn obviously bring additional manufacturing costs caused by re-melting of the bed cylinder and increased power due to the small outlet-openings. The purpose of this paper is to develop effective simulation methods of calculation for fluid flows in multiple columns, which mimic the actual complex design, and to get some useful information which can give some contributions to the die-casting industry. We have used a commercial code CFX in the numerical simulation. The primary parameter involved is the size of the air-vent. We will show how the very small opening of the outlet, i.e. the air-vent, can be treated with the aid of the porous model provided in the code. To check the validity of the numerical results we have also conducted a simple experiment by using water.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1765-1772
• /
• 2006

High-pressure die casting such as thixocasting and rheocasting is an effective process in the manufacturing automotive parts. Following the recent trend in the automotive manufacturing technologies, the product design subject to the die casting becomes more and more complex. Simultaneously the injection speed is also designed to be very high to establish a short cycletime. Thus, the requirement of the die design becomes more demanding than ever before. In some cases the product's shape can have multiple slender manifolds. In such cases, design of the inlet and outlet parts of the die is very important in the whole manufacturing process. The main issues required for the qualified products are to attain gentle and uniform flow of the molten liquid within the passages of the die. To satisfy such issues, the inlet cylinder ('bed cylinder' in this paper) must be as large as possible and simultaneously the outlet opening at the end of each passage must be as small as possible. However these in turn obviously bring additional manufacturing costs caused by re-melting of the bed cylinder and increased power due to the small outlet-openings. The purpose of this paper is to develop effective simulation methods of calculation for fluid flows in multiple columns, which mimic the actual complex design, and to get some useful information which can give some contributions to the die-casting industry. We have used a commercial code CFX in the numerical simulation. The primary parameter involved is the size of the bed cylinder. We will show how the very small opening of the outlet can be treated with the aid of the porous model provided in the code. To check the validity of the numerical results we have also conducted a simple experiment by using water.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.1
• /
• pp.31-41
• /
• 2010

This paper presents both numerical and physical modeling approaches for the dilation and spalling of rock recognized as typical process of rock around an underground opening at depth. For physical approach, laboratory testing of rectangular beams using a synthetic rock was used to investigate the onset of dilation and spalling. The beams are axially compressed and subjected to 4-point bending to provide non-uniform compressive stresses which are similar to the maximum tangential stress distribution around circular openings. Discrete element numerical analyses using commercial code $PFC^{2D}$ (Particle Flow Code) were performed to evaluate the stress path at various locations in the beams. The findings from these approaches suggest that the onset of dilation in laboratory tests appears to be a good indicator for assessing the stress magnitudes required to initiate spalling.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.20
• /
• pp.129-150
• /
• 2003

Software license agreements, to be useful in the mass market, could not be individually negotiated, and had to be standardized and concise. The software license agreement needs to be presented to the licensee-users in a fashion that would allow for mass distribution of software, also for it to enforceable, that would draw the users' attention to the terms and conditions under which the publisher allowed the use of the software. These needs have been accomplished, with or without fail, through so called the "shrink-wrap licenses" Shrink-wrap licenses purpose to transfer computer softwares to their users by defining the terms and conditions of use of the software without implicating the "first sale doctrine" of the Copyright Act. These shrink-wrap licenses have become essential to the software industry. However, in USA, the law applicable to these licenses has been unclear and unsettled. Courts have struggled to develop a coherent framework governing their enforceability. Meanwhile, the National Conference of Commissioners on Uniform State Laws ("NCCUSL") in USA promulgated the Uniform Computer Information Transaction Act ("UCITA") governing contracts for computer information transaction on July 29, 1999. One clear objective of UCITA was to settle the law governing the enforceability of shrink-wrap licenses. In these respects, this paper first introduces the various forms that shrink-wrap licenses take(at Part II. Section 1.), and explains the main advantages of them(at Part II. Section 2.) Here it shows how shrink-wrap licenses value themselves for both software publishers and users, including that shrink-wrap licenses are a valuable contracting tool because they provide vital information and rights to software users and because they permit the contracting flexibility that is essential for today's software products. Next, this paper describes the current legal framework applicable to shrink-wrap licenses in USA(at Part III). Here it shows that in USA the development of case law governing shrink-wrap licenses occurred in two distinct stages. At first stage, judicial hostility toward shrink-wrap licenses marked such that they were not enforced pursuant to Article 2 of the Uniform Commercial Code. At second stage, courts began to recognize the pervasiveness of shrink-wrap licenses, their indispensability to the rapidly expanding information technology industry, and the urgent need to enforce such licenses in order to maintain low prices for consumers of computer hardware or software, resulting in the recognition of shrink-wrap licenses. Finally, in view of the importance of UCITA, this paper examines how it will affect the enforceability of shrink-wrap licenses(at Part IV). The drafters of UCITA, as well as the scholars and practitioners who have criticized it, agree that it validates shrink-wrap licenses, provided certain procedural protections are afforded to purchasers. These procedural protections include the licensee end-user must (i) manifest his assent to the shrink-wrap license, (ii) have an opportunity to review the shrink-wrap license, (iii) have a right to return the product without costs.

• International Journal of Automotive Technology
• /
• v.6 no.1
• /
• pp.1-8
• /
• 2005

Recently, the HSDI (High Speed Direct Injection) diesel engine has been spotlighted as a next generation engine because it has a good potential for high thermal efficiency and fuel economy. This study was carried out to investigate the in-cylinder flow characteristics generated in a HSDI diesel engine with a 4-valve type cylinder head. The four kinds of cylinder head were manufactured to elucidate the effect of intake port geometry on the in-cylinder flow characteristics. The steady flow characteristics such as coefficient of flow rate $(C_{f})$, swirl ratio (Rs), and mass flow rate (m,) were measured by the steady flow test rig and the unsteady flow velocity within a cylinder was measured by PIV. In addition, the in-cylinder flow patterns were visualized by the visualization experiment and these results were compared with simulation results calculated by the commercial CFD code. The steady flow test results indicated that the mass flow rate of the cylinder head with a short distance between the two intake ports is $13\%$ more than that of the other head. However, the non-dimensional swirl ratio is decreased by approximately $15\%$. As a result of in-cylinder flow characteristics obtained by PIV and CFD calculation, we found that the swirl center was eccentric from the cylinder center and the position of swirl center was changed with crank angle. As the piston moves to near the TDC, the swirl center corresponded to the cylinder center and the velocity distribution became uniform. In addition, the results of the calculation are in good agreement with the experimental results.

• Journal of Ship and Ocean Technology
• /
• v.11 no.2
• /
• pp.10-25
• /
• 2007

With the sharp increase of the oil price, the issue of the energy saving requires even higher propulsive efficiency of the propellers. Traditionally the propellers have been designed with the criteria such as that of Lerbs optimum based on the lifting line theory and the empirical formulae of Lerbs and van Manen giving relations of the wake pitch with the wake non-uniformity. With the aid of the high speed computer, it is now possible to apply the time-consuming iterative approaches for the solution of the lifting surface problems. In this paper we formulate the variational problem to optimize the efficiency of the propeller operating in the given ship wake using the lifting surface method. The variational formulation relating the spanwise circulation distribution with the propulsive efficiency to be maximized is however non-linear in circulation distribution functions, thus the iterative method is applied to the quasi-linearized equations. The blade shape design also requires the iterative procedures, because the shape of the blade which is represented by the lifting surface is unknown a priori. The numerical code was validated with the DTNSRDC propeller 4119 which is well-known to be optimum in uniform inflow condition. In addition existing (well-designed) commercial propellers were selected and compared with the results of the open water tests and the self-propulsion tests.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.425-430
• /
• 2012

In this study, a preconverter of an MCFC for an emergency electric power supplier is numerically simulated to increase the hydrogen production from natural gas (methane). A commercial code is used to simulate a porous catalyst with a user subroutine to model three dominant chemical reactions-steam reforming, water-gas shift, and direct steam reforming. To achieve a fuel conversion rate of 10% in the preconverter, the required external heat flux is supplied from the outer wall of the preconverter. The calculated results show that the temperature distribution and chemical reaction are extremely nonuniform near the wall of the preconverter. These phenomena can be explained by the low heat conductivity of the porous catalyst and the endothermic reforming reaction. The calculated results indicate that the use of a compact-size preconverter makes the chemical reaction more uniform and provides many advantages for catalyst maintenance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.9
• /
• pp.1276-1283
• /
• 2002

Recently, HSDI (High Speed Direct Injection) diesel engine has been spotlighted as a next generation engine because it has a good potential for high thermal efficiency and fuel economy. This study was carried out to investigate the in-cylinder flow characteristics generated in a 4-valve small diesel cylinder head with a tangential and helical intake port. The flow characteristics such as coefficient of flow rate(Cf), swirl ratio (Rs), and mass flow rate (ms) were measured in the steady flow test rig using the impulse swirl meter and the analysis of in-cylinder flow field was conducted by experiment using the PIV and calculation using the commercial CFD code. As the results from steady flow test indicate, the mass flow rate of the cylinder head with a short distance between the two intake ports is increased over 13% than that of the other head. However, the non-dimensional swirl ratio is decreased approximately 15%. From in-cylinder flow characteristics obtained by PIV and CFD calculation, we found that the swirl center was eccentric from the cylinder center and the velocity distribution became uniform near the TDC. In addition, the results of the calculation are good agreement with the experimental results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.2
• /
• pp.133-140
• /
• 2003

The sandwich plate has been widely used as an efficient structural member because it has high strength-to-weight and high stiffness-to-weight ratios. To properly design the aluminum extrusion plate , it is necessary to analyze structural behaviors of the extrusions, however, the aluminum extrusions have been rarely studied until now. In the optimization process through numerous iterative calculations, finite element analysis of the sandwich plate with hollow core section requires a considerable amount of computation time and cost. In this paper, the aluminum extrusion plate with truss-core is transformed into an equivalent homogeneous orthotropic plate with appropriate elastic constants. The procedure to evaluate accurate equivalent elastic constants is also established. Using these elastic constants, simple theoretical formulas of the stresses and deflection are proposed in case of the simply-supported orthotropic thick plate under uniform pressure. Through the comparison with the results by commercial FEM code(ANSYS), it is verified that the proposed simpified formula has a good efficiency and accuracy.

• Korean Business Review
• /
• v.12
• /
• pp.303-321
• /
• 1999

Electronic commerce, driven by the development of the Internet and computer, premises to be an important engine for growth for the world economy in th the 21st century. Electronic commerce offers considerable new opportunities for the business and citizens in all regions of the world by enhancing productivity across of our economics and encourage trade in both goods and services. Specially in relation to contract, electronic commerce requires a coherent, coordinated approach internationally on key issues such as a validity, a legality, consumer protection. Electronic commerce, which breaks down national boundaries and widens the gap between the place where services are performed and the place where they are consumed, requires a new paradigm when making an between contracting parties.