• 한국음향학회지
• /
• 제38권2호
• /
• pp.161-167
• /
• 2019

본 논문은 트랙기반 중작업용 ROV(Remotely Operated underwater Vehicle)에 적용 가능한 어라운드 뷰 소나 및 굴착깊이 측정 소나의 성능 검증에 대한 내용을 다루고 있다. 현재 국산화 개발 중인 중작업용 ROV에 활용 가능한 어라운드 뷰 소나 및 굴착깊이 측정 소나를 장착하여 수조 및 실해역에서 성능 검증 실험을 수행하였다. 어라운드 뷰 소나의 경우 이미지 소나를 ROV 전후좌우 4방향에 장착하고, 굴착깊이 측정 소나는 멀티 빔 음향측심기(Multi Beam Echo Sounder, MBES) 기술로써 ROV 전방에 장착된다. 본 논문에서 개발한 소나를 장착하고 ROV를 실해역에 진수시켜 소나를 운용한 결과 소나 시스템들은 작업 중 발생하는 침전된 부유물이 발생하거나 탁도가 높은 해역에 영향을 거의 받지 않으며 어라운드 뷰 소나의 경우 ROV 전방 30 m 거리에 있는 암반지형, 자갈, 모래톱 등을 확인할 수 있었다. 그리고 굴착깊이 측정 소나의 경우 ROV가 굴착 작업을 수행 후 굴착 깊이를 측정 가능함을 확인하였다. 본 논문에서 제안한 어라운드 뷰 소나와 굴착깊이 측정 소나를 활용함으로써 작업효율성을 높일 수 있음을 입증하였다.

• 제어로봇시스템학회논문지
• /
• 제18권9호
• /
• pp.830-836
• /
• 2012

According to increasing the importance of underwater environments, the needs of UUV are growing. This paper represents the mechanism and algorithm of UUV docking system with 21-inch torpedo tubes for military submarines as a docking station. To improve the reliability of the docking, torpedo tubes launch a wired ROV and next the ROV combined with UUV is retrieved. For estimating the relative position between the ROV and UUV, in this paper, combining RF sensors and vision system is proposed. The RSSI method of RF sensors is used to estimate the distance and the optical image is combined for the directional information.

• 한국정보통신학회논문지
• /
• 제10권11호
• /
• pp.1973-1977
• /
• 2006

본 논문에서는 IMU(Inertial Motion Unit), DVL(Doppler Velocity Log), USBL(Ultra Short Base Line) DGPS(Differential Global Positioning System) 등의 센서로부터 취득된 데이터를'융합하여 ROV(Remotely Operated Vehicle)와 AUV(Autonomous Underwater Vehicle)와 같은 수중체의 위치를 지구 전체영역에서 추정하기 위한 기본적인 알고리즘을 다루고 있다. 본 논문에 소개된 알고리즘은 6,000m급 과학 조사용 심해무인잠수정인 해미래[1]의 수중 위치추적에 사용될 예정이다.

• 로봇학회논문지
• /
• 제15권1호
• /
• pp.39-47
• /
• 2020

This paper presents a control and operation system for a remotely operated vehicle (ROV). The ROV used in the study was equipped with a manipulator and is being developed for underwater exploration and autonomous underwater working. Precision position and attitude control ability is essential for underwater operation using a manipulator. For propulsion, the ROV is equipped with eight thrusters, the number of those are more than six degrees-of-freedom. Four of them are in charge of surge, sway, and yaw motion, and the other four are responsible for heave, roll, and pitch motion. Therefore, it is more efficient to integrate the management of the thrusters rather than control them individually. In this paper, a thrust allocation method for thruster management is presented, and the design of a feedback controller using sensor data is described. The software for the ROV operation consists of a robot operating system that can efficiently process data between multiple hardware platforms. Through experimental analysis, the validity of the control system performance was verified.

• 한국해양공학회지
• /
• 제20권3호
• /
• pp.7-14
• /
• 2006

This paper discusses the structural design and analysis of a 6,000 meters depth-rated capable deep-sea unmanned underwater vehicle (UUV) system. The UUV system is currently under development by Maritime and Ocean Engineering Research Institute(MOERI), Korea Ocean Research and Development Institute (KORDI). The UUV system is composed of three vehicles - a Remotely Operated Vehicle (ROV), an Autonomous Underwater Vehicle (AUV) and a Launcher - which include underwater equipment. The dry weight of the system exceeds 3 tons hence it is necessary to carry out the optimal design of structural system to ensure the minimum weight and sufficient space within the frame for the convenient use of the embedded equipments. In this paper, therefore, the structural design and analysis of the ROV and launcher frame system were carried out, using the optimizing process. The cylindrical pressure vessels for the ROV were designed to resist the extreme pressure of 600 bars, based on the finite element analysis. The collapse pressure for the cylindrical pressure vessels was also checked through a theoretical analysis.

• 한국해양공학회지
• /
• 제33권2호
• /
• pp.178-188
• /
• 2019

When burying underwater cables using robots, heading control is one of the key functions for the robots to improve task efficiency. This paper addresses the heading control issue for URI-T, an ROV for underwater construction tasks, including the burial and maintenance of cables or small diameter pipelines. Through modeling and identifying the heading motion of URI-T, the dynamic characteristics and input limitation are analyzed. Based on the identification results, a PD type controller with appropriate input treatment is designed for the heading control of URI-T. The performance of the heading controller was verified in water tank experiments. The field applicability of the proposed controller was also evaluated through the sea trial of URI-T at the East Sea, with a water depth of 500 m.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권4호
• /
• pp.451-458
• /
• 2012

수중의 작업 목적에 따라 ROV와 AUV의 두 가지 용도로 사용할 수 있는 새로운 구조의 변신 6자유도 수중로봇의 설계연구를 하였다. CROV의 ROV모드와 AUV모드에 대한 각각의 구조 설계연구를 수행하였으며 각각의 모드에 대한 제어시스템을 설계하고 AUV의 경우에는 추력에 따른 항해속도에 대한 해석을 수행하였다. ROV나 AUV의 정확한 위치 및 속도를 추정할 수 있도록 다양한 센서신호를 퓨전하여 처리하는 센서퓨전보드를 제작하고 확장 칼만필터를 포함하는 전체 제어시스템을 설계하고 제작하였다.

• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.579-589
• /
• 2008

In the past few years, there are many studies and researches of the underwater vehicles which are carried out its mission using sonar sensors. MSCL(Marine System Control Lab.) at Inha University developed test-bed small ROV, ISRO. ISRO is an open-frame type and has 4 thrusters. ISRO can control 4 motions i.e surge, sway, yaw and heave with sonar sensors. ISRO is developed for inspection of ship hull, marine structure, plant of lake or river and so on. When ROV ISRO inspects something, it is necessary to control the position of ROV ISRO's for the movement and anti-collision with structures in the underwater. In this paper, we deal with the development of a small ROV and verification of the position control system via simulation and experiment using sonar sensors.

• 한국해양공학회지
• /
• 제34권3호
• /
• pp.180-193
• /
• 2020

In this study, the end-effector tracking performance of a manipulator installed on a remotely operated vehicle (ROV) for autonomous underwater intervention is verified. The underwater manipulator is an ARM 7E MINI model produced by the ECA group, which consists of six joints and one gripper. Of the six joints of the manipulator, two are revolute joints and the other four are prismatic joints. Velocity control is used to control the manipulator with forward and inverse kinematics. When the manipulator approaches a target object, it is difficult for the ROV to maintain its position and posture, owing to various disturbances, such as the variation in both the center of mass and the reaction force resulting from the manipulator motion. Therefore, it is necessary to compensate for the influences and ensure the relative distance to the object. Simulations and experiments are performed to track the trajectory of a virtual object, and the tracking performance is verified from the results.

• 한국해양공학회지
• /
• 제33권5호
• /
• pp.454-461
• /
• 2019

In autonomous interventions using an underwater vehicle with a manipulator, grasping based on target detection and recognition is one of the core technologies. To complete an autonomous grasping task, the vehicle body approaches the target closely and then holds it through operating the end-effector of the manipulator, while the vehicle maintains its position and attitude without unstable motion. For vehicle motion control, it is very important to identify the hydrodynamic parameters of the underwater vehicle, including the propulsion force. This study examined the propulsion characteristics of the autonomous intervention ROV developed by KRISO, because there is a difference between the real exerted force and the expected force. First, the mapping between the input signal and thrusting force for each underwater thruster was obtained through a water tank experiment. Next, the real propulsion forces and moments of the ROV exerted by thrusting forces were directly measured using an F/T (force/torque) sensor attached to the ROV. Finally, the differences between the measured and expected values were confirmed.