• Tribology and Lubricants
• /
• v.15 no.3
• /
• pp.233-239
• /
• 1999

Generally quantity of supply oil for piston ring lubrication in an internal combustion engine may be insufficient to fill the entire volume formed in the clearance between piston ring and cylinder liner. Thus oil starvation condition should be considered for the analysis of piston ring lubrication. In order to reasonably estimate amount of oil left on the cylinder liner, adequate boundary condition should be adapted for the analysis of ring pack lubrication. In this analysis of ring pack lubrication of an internal combustion engine, oil starvation and open-end boundary conditions are considered at inlet and outlet of piston rings. It is revealed that piston rings are operated under oil starvation in most operating cycle and the result with these conditions are quite different from that with fully-flooded assumption.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.80-82
• /
• 2009

The dependence of the efficiency characteristics of hydrogenated amorphous silicon single junction solar cells on the various intrinsic layer thickness has been investigate in the glass/$SnO_2$:F/p,i,n a-Si:H/Al type of amorphous silicon solar cells by cluster PECVD system. The open circuit voltage, short circuit current, fill factor and conversion efficiency have been measured under AM 1.5 condition. The result of the cell performance was improved about 8.2% due to an increase in the short circuit current.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.12-16
• /
• 2020

This study investigates the degradation characteristics of different material types of ethyl vinyl acetate (EVA) and polyolefin (POE) with combining transparent backsheet. To this end, we fabricated samples with structure of glass/encapsulant/transparent backsheet for each type of encapsulants, and shingled Si modules with the same structure. The samples were then subjected to accelerated test by storing under damp heat condition of 85℃ and 85% RH. As a result, encaplsulant discoloration was observed, which the transmittance of the samples with EVA decreased in a rapid rate than the samples with POE. The discoloration also affected a power degradation of the shingled modules with a reduction of current density, resulting that the module with EVA showed more drop on the efficiency than the modules with POE. Furthermore, corrosion of the soldered ribbon caused by acetic acid produced from the degraded EVA also contributed in fill factor reduction.

• Structural Engineering and Mechanics
• /
• v.51 no.6
• /
• pp.1017-1036
• /
• 2014

Steel tubes have an efficient shape with large second moment of inertia relative to their light weight. One of the main problems of these members is their low buckling resistance caused from having thin walls. In this study, steel foams with high strength over weight ratio is used to fill the steel tube to beneficially modify the response of steel tubes. The linear eigenvalue and plastic collapse FE analysis is done on steel foam filled tube under pure compression and three point bending simulation. It is shown that steel foam improves the maximum strength and the ability of energy absorption of the steel tubes significantly. Different configurations with different volume of steel foam and composite behavior is investigated. It is demonstrated that there are some optimum configurations with more efficient behavior. If composite action between steel foam and steel increases, the strength of the element will improve, in a way that, the failure mode change from local buckling to yielding.

• Current Photovoltaic Research
• /
• v.4 no.2
• /
• pp.48-53
• /
• 2016

We report the effect of physical load on the stability of organic solar cells under physical loads. The active layers in organic solar cells were fabricated with bulk heterojunction films (BHJ) films of poly (3-hexylthiophene) and phenyl-$C_{61}$-butyric methyl ester. The loading time was varied up to 60 s by keeping the physical load constant. Results showed that the open circuit voltage was not influenced by the physical load but other solar cell parameters were sensitive to the loading time. The fill factor was very slightly increased at 15 s, while short circuit current density was well kept for 30 s. The power conversion efficiency was reasonably maintained for 45 s but became significantly decreased by the continuous loading for 60 s.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.60-63
• /
• 1993

We have prepared n-CdS/p-InP hetero- junction solar cells by thermal evaporation. The efficiency under the optium conditions without the grid line contact was 7.3%, and the solar cell having glid line contact with SiO AR coating was the open circuit voltage of 0.71V, the short circuit voltage current density of 15mA/cm$^2$, the fill factor of 0.73, and the efficiency of 11.5%. As result of photoresponse in 400-1000nm wavelength the cutoff of n-CdS/p-InP solar at 500nm results from absorption by the CdS \"window\" and the cutoff at 930 nm result from absorption by the InP.

• Journal of the Optical Society of Korea
• /
• v.12 no.1
• /
• pp.57-61
• /
• 2008

We investigated the laser pulse-width dependence of dense plasmas confined within the magnetic length of $In_{0.2}Ga_{0.8}As$/GaAs multiple quantum wells under high magnetic fields up to 31 T. To fully fill the Landau levels of effectively zero-dimensional system, we used intense femtosecond (fs) laser pulses to create carrier densities near $10^{13}/cm^2$. The observed photoluminescence showed a characteristic of superfluorescence, above critical magnetic field when being excited by pulses shorter than coherence buildup time.

• Geomechanics and Engineering
• /
• v.6 no.4
• /
• pp.377-389
• /
• 2014

The vacuum consolidation method which was proposed by Kjellman in 1952 has been studied extensively and used successfully since early 1980 throughout the world, especially in East and Southeast Asia. Despite the increased successful use, different opinions still exist, especially in connection to distribution of vacuum with depth and time in vertical drains and in soil during preloading of soft ground. Porewater pressure measurements from actual cases of field vacuum and vacuum-fill preloading as well as laboratory studies have been examined. It is concluded that (a) a vacuum magnitude equal to that in the drainage blanket remains constant with depth and time within the vertical drains, (b) as expected, vacuum does not develop at the same rate within the soil at different depths; however, under ideal conditions vacuum is expected to become constant with depth in soil after the end of primary consolidation, and (c) there exists a possibility of internal leakage in vacuum intensity at some sublayers of a soft clay and silt deposit. A case history of vacuum loading with sufficient subsurface information is analyzed using the ILLICON procedure.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.2
• /
• pp.23-29
• /
• 2014

Less power consumption, lower cost, smaller size and more functionality are the increasing demands for consumer electronic devices. The three dimensional(3-D) TSV packaging technology is the potential solution to meet this requirement because it can supply short vertical interconnects and high input/output(I/O) counts. Cu(Copper) has usually been chosen to fill the TSV because of its high conductivity, low cost and good compatibility with the multilayer interconnects process. However, the CTE mismatch and Cu ion drift under thermal stress can raise reliability issues. This study discribe the thermal stress reliability trend for successful implementation of 3-D packaging.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.17 no.31
• /
• pp.59-72
• /
• 1994

This paper deals with ordering policies of consumable goods which have large demand rates in a multi-level distribution system. The system we are concerned consists of one Central Distribution Center(CDC) and N non-identical Regional Distribution Centers(RDCs) which have different demand rates, minimum fillrates, leadtimes, etc. The customer demand on the RDC is stationary poisson and the RDCs demand on the CDC is superposition of Q-stage Erlang distributions. We approximate the RDCs and CDC demand distribution to nomal in order to enhance the efficiency of algorithm. The relevant costs include a fixed ordering cost and inventory holding cost, and backorder cost. The objective is to find a continuous-review ordering policy that minimizes the expected average costs under constraints of minimum fill rates of RDCs and maximum allowable mean delay of CDC. We developed an algorithm for determining the optimal ordering policies of the CDC and the RDCs. We verified and compared the performance of the algorithm through the simulation using the algorithm result as the input parameters.