• Journal of Animal Science and Technology
• /
• 제64권2호
• /
• pp.343-352
• /
• 2022

Pig slaughterhouses harbor high humidity because of the necessary cleaning that takes place simultaneously with slaughter, which facilitates the existence of mold. Due to the enclosed space, there are several limitations to the control of mold growth with respect to cleaning, ventilation, and drying. In this study, the prevalence of fungi was investigated in four pig slaughterhouses in Korea. Four fungi (Aspergillus niger, Penicillium commune, Penicillium oxalicum, and Cladosporium cladosporioides) were detected with the highest frequency. These four strains were subjected to various treatments to reduce their growth. The fungi were inoculated onto stainless steel (SS) chips and treated with ultraviolet (UV)-C irradiation and hot water. Individual treatments with UV-C (15, 30, 90, 150, 300, and 600 mJ/cm²), and hot water (60, 65, 70, and 83℃) were performed to sanitize the SS chips. Simultaneous cleaning with 60℃ hot water and more than 150 mJ/cm² of UV-C reduced the fungal incidence by > 6.5 Log from 6.6-7.0 Log CFU/cm² (initial count). Our results demonstrate that a combined treatment of UV-C and hot water is the most economical and convenient way to prevent microbiological contamination of small tools (such as knives and sharpeners) and steel surfaces in slaughterhouses.

• Current Optics and Photonics
• /
• 제6권2호
• /
• pp.202-211
• /
• 2022

In the pasteurization of escalator handrails using ultraviolet (UV) sterilizers, a combination of light distribution and escalator speed has priority over other important factors. Furthermore, since part of the escalator handrail has a curved structure, proper design is needed to improve the sterilization rate on the surfaces touched by users. In this paper, two types of sterilizers satisfying these conditions are manufactured with 275-nm UV-C LEDs, after modeling the three-dimensional (3D) structure of an escalator handrail and simulating optical distributions of UV-C irradiation on the handrail's surface according to light-emitting diode (LED) positions and reflector variations in the sterilizers. Pasteurization experiments with the UV-C LED sterilizers are conducted on six types of gram-positive and gram-negative bacteria, with exposure times of 0.2, 5, and 15 s at an actual installation distance of 20 mm. The sterilization rates for the gram-positive bacteria are 10.63% to 27.94% at 0.2 s, 89.44% to 96.30% at 5 s, and 99.64% to 99.88% at 15 s. Those for the gram-negative bacteria are 57.70% to 77.63% at 0.2 s, 98.90% to 99.49% at 5 s, and 99.88% to 99.99% at 15 s. The power consumption of the UV-C LED sterilizer is about 8 W, which can be supplied by a self-generation module instead of an external power supply.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.97-100
• /
• 2000

Si$_2$Sr$_2$CuO$\sub$x/(Bi(2201)) thin films are fabricated by atomic layer by layer deposition using ion beam sputtering(IBS) method. During the deposition, 10 %-ozone/oxygen mixture gas of typical 5.0 ${\times}$ 10$\^$-5/ Torr is applied with ultraviolet light irradiation for oxidation. XRD and RHEED investigations reveal out that a buffer layer with some different compositions is formed at the early deposition stage of less than 10 units cell and then c-axis oriented Bi(2201) is grown.

• 대한전자공학회논문지
• /
• 제26권10호
• /
• pp.1535-1544
• /
• 1989

The overhang structure of photoresist in optical lithography was studied for the metallization of GaAs-related devices throughout lift-off method. Optical contact aligner with a dose of 8.5 m J/cm\ulcornerand with a wavelength of 300mm was used for ultraviolet exposure of single layer of S1400-27 photoresist. The overhang thickness shows a linear relationship with the soaking time in monochlorobenzene, which its magnitude becomes high at elevated softbake temperature. Such process conditions as a low softbake temperature, a long monochlorohbenzene soaking time and a little exposed energy make the development rate of photoresist lower. The optimum process conditions to obtain a target line-width, which include an appropriate overhang structure such as complete separation between the sidewall of photoresist pattern and the deposited metal edge, are determined as the softbake temperature of 64-74\ulcornerC, the monochlorobenzene soaking time of 10-15min, the ultraviolet exposure time of 70-100sec and the development time of 50-80sec.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.824-829
• /
• 2007

Mechanical and thermal analysis properties of carbon fiber/epoxy composite for train carbody were evaluated by varying with environmental factors such as ultraviolet, temperature, and moisture. Accelerated environmental aging tester was utilized for this study. Testing temperature was set to $80^{\circ}C$ and ultraviolet was obtained through xenon-arc lamp. To consider moisture, water sprayed on specimen for 18 minutes every 2 hour. All the specimens were made of CF1263/Epoxy composite. Mechanical properties such as tensile, bending, and shear properties were evaluated through a material testing system. Also, thermal analysis properties such as storage shear modulus, loss shear modulus, and tan ${\delta}$ were measured through dynamic mechanical analyzer. Finally surfaces of the composite exposed to environmental factors were examined using a scanning electron microscope. From experimental results, those properties of CF1263/Epoxy composite were shown to be slightly decreased due to environmental factors.

• Elastomers and Composites
• /
• 제52권2호
• /
• pp.131-135
• /
• 2017

Zinc nitrate hexahydrate [$Zn(NO_3){\cdot}6H_2O$] and sodium hydroxide [NaOH] were used as source reagents in the preparation of ZnO nanoparticles in an aqueous solution containing deionized water and ethanol in a ratio of 2:5 (v/v). ZnO nanoparticles were heated in an electric furnace at $700^{\circ}C$ for 2 h under an atmosphere of inert argon gas. The morphological and structural properties of the nanoparticles were characterized by scanning electron microscopy (SEM) and powder X-ray diffractometry (XRD). UV-vis spectrophotometry was used to analyze the photocatalytic degradation of 3-nitrophenol with ZnO nanoparticles as photocatalyst under ultraviolet irradiation at 254 nm. Evaluation of the kinetic of the photo-catalytic degradation of 3-nitrophenol indicated that the degradation of 3-nitrophenol with ZnO nanoparticles obeyed the pseudo-first order reaction rate model.

• 복식문화연구
• /
• 제21권5호
• /
• pp.699-707
• /
• 2013

The natural dyeing of silk fabric with Thuja orientalis extract was investigated. The proper colorant concentration, dyeing temperature, dyeing time, and pH for the dyeing of silk fabric with Thuja orientalis extract were 100% v/v, $80^{\circ}C$, 80 minutes and pH 3, respectively. In various mordanted methods, the K/S values of mordanted methods were higher than those of unmordanted methods with increasing mordant concentration. Light colorfastness and washing colorfastness of Cu or Fe mordanted silk fabric was improved by mordanting. The antibacterial properties of dyed and mordanted silk fabric showed a high reduction rate, and Thuja orientalis extract was showed effective bacterial reduction. The dyed and mordanted fabric with Thuja orientalis extract showed a superior ultraviolet protection property.

• 산업기술연구
• /
• 제27권B호
• /
• pp.3-7
• /
• 2007

Ultraviolet light(UV-C, wavelength: 200~280nm) is employed profitably for sterilizing drinking water. For most water serving apparatus such as a water purifier, a water cooler and heater, a coffee vending machine and etc., pre-sterilized water may be contaminated secondarily with bacillary inhabitation in a container before serving. In consideration of this problem, a household water tap which is equipped with a sterilization/Purification device in combination with non-contact UV-lamp, was designed to sterilize and purify water at the last outlet just before serving. Hopefully this simple but creative item may be commercialized for household and public use.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.97-100
• /
• 2000

Bi$_2$Sr$_2$CuO$\sub$x/(Bi(2201)) thin films are fabricated by atomic layer by layer deposition using ion beam sputtering(IBS) method. During the deposition, 10 %-ozone/oxygen mixture gas of typical 5.0 ${\times}$ 10$\^$-5/. Torr is applied with ultraviolet light irradiation for oxidation. XRD and RHEED investigations reveal out that a buffer layer with some different compositions is formed at the early deposition stage of less than 10 units cell and then c-axis oriented Bi(2201) is grown.

• 한국의류학회지
• /
• 제26권8호
• /
• pp.1177-1185
• /
• 2002

This study was to develop the sunshade hat which reduced stress from solar radiation and ultraviolet radiation (UV), in order to keep the farmer's health and to promote their work efficiency. The new sunshade hat with a large brim, special structure for ventilation, stability and portability was designed and tested with manikin heads outdoors. Two newly designed sunshade hats(A, B) and three existing hat were tested Sunshade hat A made of double fabric with aluminum coating-nylon and black cotton cloth with a polyester mix(T/C) was the most protective from solar radiation. Sunshade hat B with larger brim was the most protective from ultraviolet radiation, even though it was made of aluminum coating-nylon single fabric.