• 조명전기설비학회논문지
• /
• 제13권4호
• /
• pp.38-46
• /
• 1999

본 연구는 고전압 전력기기에서 코로나에 의한 절연열화를 진단하기 위해 초음파 측정법을 사용하여 코로나의 진전상태에 따른 초음파신호를 분석하였으며, 또한 방전전하량과 초음파 펄스수의 관계를 조사하였다. 실험결과, 교류전압 인가시 코로나가 성장하여 브러시 또는 스트리머 코로나 형태에서 초음파신호는 처음으로 관측되었으며, 이때 관측된 초음파신호는 정극성 최대치에서 검출할 수 있었다. 전압이 상승함에 따라 정극성이 부극성에 비해 초음파의 발생빈도는 높게 나타났으며, 초음파신호의 크기는 전류펄스의 크기에 비례하였다. 그리고 초음파 펄스수는 방전전하량에 비례하여 증가된 것으로 나타났다. 옥외 전력기기에 대한 초음파 측정시 기본데이터를 얻기 위해 초음파의 발진 및 수신장치를 이용하여 공중초음파의 감쇄, 시간지연 및 지향특성도 조사하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1702-1704
• /
• 1998

In order to establish the usefulness of ultrasonic techniques for detecting corona discharges in high-voltage power apparatus, it is first necessary to determine the relationship between electrical and ultrasonic signals of corona discharges in air. In this paper, various characteristics of ultrasonic signal detection for point-to-plane corona discharges using a 200[kHz] ultrasonic sensor are examined. In regard to the attenuation and directivity of ultrasonic signals, the signals were inversely proportional to the distance between corona sources and ultrasonic receiving sensors, and half attenuation angles were approximately 7.0 degree. Ultrasonic signals of positive polarities were first obserbed at corona inception voltages. and the signals were increased with increasing the applied voltages.

• 한국산업정보학회논문지
• /
• 제22권5호
• /
• pp.25-30
• /
• 2017

본 논문에서는 초음파 센서를 이용한 저비용 장애물 인식 장치를 개발한다. 개발된 장애물 인식 장치는 시각 장애인들이 보행시 장애물을 인식하는 데 쓰일 수 있도록 한다. 장애물의 인식 여부는 내장된 모터의 진동을 통하여 시각 장애인들에게 인식이 가능하도록 한다. 뿐만 아니라 장애물의 거리에 따라 대상자에게 장애물 인식 유무에 대해 시간차를 두고 고지하여 대상자가 장애물에 대해 적절한 반응을 수행할 수 있도록 한다. 마이크로 컨트롤러 제어를 통한 펄스 신호를 이용하여 장애물에 대한 반사파를 통해 장애물의 존재 유무와 거리를 탐지하며 펄스 신호를 이용한 반사파 탐지는 반복 수행을 통해 인식률을 높인다. 개발된 장애물 인식 장치는 $30^{\circ}$ 내외의 전방 탐지각을 나타내고, 2cm-30cm의 탐지거리를 가지며 일상적인 보행 조건에서 동작이 가능함을 실험을 통해 입증하였다.

• 비파괴검사학회지
• /
• 제11권2호
• /
• pp.42-47
• /
• 1991

Nondestructive evaluation study was made on creep damage materials by ultrasonic spectrum analysis. The evaluation methods was developed in order to predict the change of ultrasonic attenuation with increasing creep damage. A new algorithm for the improvement of measuring accuracy of ultrasonic attenuation using a spectrum analysis has been developed. Normally, the ultrasonic attenuation is evaluated from 1st and 2nd peak values of the pulse-echo ultrasonic wave. The algorithm developed is incorporated in a measuring system which consists of a personal computer with ultrasonic apparatus and a digital storage oscilloscope. By the spectrum analysis method, it become popssible to describe approximately the attenuation change with increassing creep damage in Cr-Mo-V forging.

• Nuclear Engineering and Technology
• /
• 제36권1호
• /
• pp.12-23
• /
• 2004

In the present study a new measurement technique has been developed, which uses an ultrasonic transmission signal in order to identify the vertical two phase flow pattern. The ultrasonic measurement system developed in the present study not only provides the information required for the identification of vertical two phase flow patterns but also makes real time identification possible. Various vertical two phase flow patterns such as bubbly, slug, churn, annular flow etc. have been accurately identified with the present ultrasonic measurement system under atmospheric condition. In addition, the present test apparatus can practically simulate the ultrasonic propagation characteristics under high temperature and high pressure systems. Therefore, it is expected that the present ultrasonic flow pattern identification technique could be applicable to the vertical two phase flow systems under high temperature and high pressure conditions.

• 비파괴검사학회지
• /
• 제28권3호
• /
• pp.279-284
• /
• 2008

The firmness of fruit is one of the most important quality factors and is highly correlated to the elastic modulus. In this study, the ultrasonic transmission method was applied to evaluate the elastic modulus of the apple. In order to transmit and receive the ultrasonic wave through the whole apple, the ultrasonic measurement setup consisted of ultrasonic pulser, two specially fabricated ultrasonic transducers for fruit and digital storage oscilloscope. Ultrasonic parameters such as ultrasonic wave velocity, apparent attenuation, and peak frequencies were analyzed. The elastic modulus of apple was measured by using compression test apparatus. The correlations between ultrasonic parameters and elastic modulus were analyzed. A multiple linear regression model describing the relationship between elastic modulus and ultrasonic parameters was proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1512-1517
• /
• 2003

Augmentation of CHF by ultrasonic is experimentally studied under subcooling pool boiling condition. Experiment is carried out for downward-facing plate with and without the ultrasonic. The working fluid is distilled water. Experimental apparatus is composed of a bath, power supply, test section, ultrasonic generator, DAQ system. Experiment is performed with the subcooling temperature of $5^{\circ}C$, $20^{\circ}C$, $40^{\circ}C$ and the inclined angle of $0^{\circ}$, $10^{\circ}$, $20^{\circ}$, $45^{\circ}$, 90. From the experimental results, it is found that ultrasonic effect enhances CHF of the downward-facing plate. As increasing the degree of subcooling, the rate of CHF increase is enhanced. As increasing the inclined angle, the rate of CHF increase decreases. Also, we can see that the heat transfer mechanism of CHF augmentation is closely connected with the dynamic behavior of bubble generation and departure.

• 대한기계학회논문집B
• /
• 제23권7호
• /
• pp.893-900
• /
• 1999

Measuring temperature with ultrasonic wave apparatus is desirable in the cue of gas below $300^{\circ}$ because of the fact that the temperature of gas is the function of only sound velocity. In this study, being used a heatable wind channel and a blower. the variation of temperature is observed in accordance with flow rate(air velocity). The frequency modulation method is used to measure the temperature which is varying in hot air flow up to $100^{\circ}$. The length changed in the position of ultrasonic sensors is considered. Also. the effects of air velocity at the same temperature and various facing angles of ultrasonic sensors are considered. As a result of this study. it has been found that the temperature in gas flow is correctly measured regardless of both the distance of ultrasonic sensors and the variation of air velocity. and that there is just a little influence of facing angles.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.42-44
• /
• 2003

The paper presents the method and apparatus for conformal photoresist spray coating on the 3D structured substrate. The system consists of a high-temperature-rotational chuck, ultrasonic spray nozzle module, angle control module and nozzle moving module. The coating uniformity is acquired by controlling the moving speed of the ultrasonic spray nozzle across the substrate which is rotated constantly. To coat the photoresist conformally the spray angle of the nozzle and the temperature of the substrate are controlled during spray coating. The rotational chuck can be heated up by hot air or $N_2$. The photoresist (AZ1512) has been coated on the 3D structured wafer by spray coating system and the characteristics have been evaluated.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1998년도 추계 학술발표회 논문집
• /
• pp.150-160
• /
• 1998

Measuring temperature with ultrasonic wave apparatus is desirable in the case of both below 300$0^{\circ}C$ and ideal gas because of the fact that the temperature of gas is the function of only sound velocity. In this study, being used a heatable wind channel and a blower, the variation of temperature is observed in accordance with diverse flow rate(air velocity). The frequency modulation method is used to measure the temperature which is varying in hot air flow till 10$0^{\circ}C$. The length changed in the position of ultrasonic sensors is considered. Also, the effects of air velocity at the same temperature and various facing angles of ultrasonic sensors are considered. As a result of this study, it has been found that the temperature in gas flow is correctly measured regardless of both the distance of ultrasonic sensors and the variation of air velocity, and that there is just a little influence of facing angles.