• Journal of Advanced Navigation Technology
• /
• v.13 no.1
• /
• pp.41-47
• /
• 2009

In this paper, a band pass filter with a rejection band is proposed for UWB(Ultra Wide Band) communication system. First, low pass filter accessed cut off frequency of 10.2 GHz was designed using structure stepped impedance. And high pass filter accessed cut of frequency of 3.2 GHz was designed using parallel short-stub. There was implemented composite connection of designed low pass filter and high pass filter. The relative dielectric constant, the height, the loss tangent of the PCB substrate were ${\varepsilon}_r$=2.2, h=0.508 mm and loss tangent = 0.0009 respectively. The fabricated band pass filter shows a compact size of 3 cm. The fabricated band pass filter was characterized using 37169A VNA(Vector Network Analyzer). And measured result were obtained 7.5 GHz of bandwidth and -10 dB of return loss and -3 dB of insertion loss from pass band. The result of the research can be used for the UWB communications and MIC/MMIC, RFIC system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.11
• /
• pp.972-977
• /
• 2016

This paper introduces development process and results of HF & UHF band(13.56 MHz, 920 MHz) tag antennas using a single-side printing method on a PE film. The size of tag antenna is designed in the area of $80mm{\times}50mm$, little bit smaller than a credit card. The UHF tag antenna, $76mm{\times}44mm$, is located at the outside of the card size tag antenna, and the HF tag antenna, $40 mm{\times}42 mm$, is located at the center of the UHF tag antenna. The UHF and HF tag antennas are designed with consideration of coupling effects. The single-side printing method with a jumper structure without using a via is used to make a loop antenna of HF tag antenna. The reading range of UHF tag antenna is about 6m, and the reading of HF tag antenna is about 5 cm. The designed tag antennas have long enough reading ranges for both bands. The tag is applicable to logistics and authentification.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.8
• /
• pp.1759-1764
• /
• 2015

In this paper, we considered a design method of a circular polarization (CP) antenna for UHF (ultra high frequency) RFID (Radio Frequency IDentification) readers. The antenna is a dual-fed circular microstrip patch which produces right-handed CP. Quadrature hybrid coupler is used for dual feeding. The outputs of the coupler and circular patch are connected through copper wires, and the inductive reactance produced by the connecting wires is compensated by a ring-shaped slot inserted inside the circular patch. The effects of the geometrical parameters of the proposed antenna on the antenna performance are examined, and the parameters are adjusted to be suitable for the operation in North American UHF RFID band (902-928 MHz), which includes domestic UHF RFID band. The antenna is fabricated, and the experiment results reveal a frequency band of 854-993 MHz for a voltage standing wave ratio < 2. The fabricated antenna is connected to a commercial RFID reader, and it showed a good performance of tag identification.

• Nutrition Research and Practice
• /
• v.18 no.1
• /
• pp.132-148
• /
• 2024

BACKGROUND/OBJECTIVES: This study aimed to assess the current mean daily intake of 10 food groups, analyze the sociodemographic factors associated with food consumption, and determine the associations between food consumption/dietary intake and the prevalence rates of obesity, type 2 diabetes (T2D), and hypertension (HTN) in Jakarta, Indonesia. SUBJECTS/METHODS: A total of 600 participants aged 20-85 yrs were included in this cross-sectional study. Food consumption and dietary habits were assessed using a food frequency questionnaire. To determine the association between food consumption/dietary habits and the abovementioned diseases, logistic regression analysis was performed. RESULTS: The average vegetable and fruit intake was lower, while sugar and salt consumption were higher than that recommended by Indonesia's national dietary guidelines. A high intake of ultra-processed foods (UPFs) was associated with young age, men, "single" status, a high education level, and employment with a high monthly income. Obesity and T2D were positively correlated with high intakes of cereals and tubers, UPFs, sugars, fats, and oils. Conversely, an inverse association was found between legume, vegetable, and fruit consumption and obesity risk. An inverse correlation was also observed between vegetable consumption and T2D risk. Moreover, a high salt intake was inversely correlated with fruit consumption in terms of HTN risk. Non-indulgence in habitual late-night snacking and refrainment from consuming more than one dish at each meal were also negatively related to the prevalence of obesity, T2D, and HTN. Inverse correlations were also observed between the prevalence rates of T2D and HTN and abstaining from adding sugar to beverages. CONCLUSION: Foods high in fat, sugar, and sodium were strongly associated with the risks of obesity, T2D, and HTN. Additionally, poor eating habits were also associated with disease development.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.117-124
• /
• 2009

This paper describes a 3 to 5 GHz frequency synthesizer for MB-OFDM (Multi-Band OFDM) UWB (Ultra- Wideband) application using 0.13 ${\mu}m$ CMOS process. The frequency synthesizer operates in the band group 1 whose center frequencies are 3432 MHz 3960 MHz, and 4488 MHz. To cover the overall frequencies of group 1, an efficient frequency planning minimizing a number of blocks and the power consumption are proposed. And, a high-frequency VCO and LO Mixer architecture are also presented in this paper. A new mixed coarse tuning scheme that utilizes the MIM capacitance, the varactor arrays, and the DAC is proposed to expand the VCO tuning range. The frequency synthesizer can also provide the clock for the ADC in baseband modem. So, the PLL for the ADC in the baseband modem can be removed with this frequency synthesizer. The single PLL and two SSB-mixers consume 60 mW from a 1.2 sV supply. The VCO tuning range is 1.2 GHz. The simulated phase noise of the VCO is -112 dBc/Hz at 1 MHz offset. The die area is 2 ${\times}$ 2mm$^2$.

• Tribology and Lubricants
• /
• v.33 no.2
• /
• pp.52-58
• /
• 2017

An ultra-high precise ejection process is essential in a dispensing system for fabricating various precision parts such as a semiconductor, LED, and camera module. The size of such parts has been decreasing, which implies that a precise ejecting technique is required. A phosphor-containing liquid is ejected via a dispenser using dual piezoelectric actuators that are used for generating a high-speed dispensing mechanism. The rod and nozzle continuously contact in high speed to eject the liquid. However, the high-strength filler or phosphor in the liquid causes wear on the surfaces of the rod and nozzle during the dispensing process. As a result, the ejection reliability decreases as the wear on the surfaces increases. Therefore, it is necessary to estimate the wear characteristics of the rod and nozzle via an experiment and FE analysis. Reliability rests up to 1,000 cycles are conducted under relatively severe conditions. The flow rate and surfaces roughness of the rod and nozzle are measured in each ejection cycle. The surface images and wear volume are obtained before and after the tests and the ejection reliability is confirmed by measuring the flow rate of the liquid. The experimental results show that the ejection reliability is maintained up to 1,000k cycles; these results are validated by the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.323-332
• /
• 2009

In this paper, we introduce a modified short-circuited stub bandpass filter suitable for ultra-wideband(UWB) applications utilizing low temperature co-fired ceramic(LTCC) technology. By modifying the conventional short-circuited stub bandpass filter structure with stubs and connecting lines of lower characteristic impedances, the number of stubs has been reduced from 5 to 2 on a high dielectric constant substrate($\varepsilon_r$ = 40). A wireless local area network (WLAN) stopband in the frequency range of 5.15 to 5.825 GHz has been inserted into the filter characteristic using three short-circuited coupled lines. The filter has been measured with an insertion loss less than 1.0 dB and return loss better than 10 dB in the pass bands. A bandwidth ratio of 109.49 % has been achieved. Measurement results agree well with simulation results. The dimensions of the filter are $4{\times}8{\times}0.57\;mm^3$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.361.1-361.1
• /
• 2016

Due to their high sensitivity, fast response, small energy consumption and ease of integration, nanoelectromechanical systems (NEMS) have attracted much interest in various applications such as high speed memory devices, energy harvesting devices, frequency tunable RF receivers, and ultra sensitive mass sensors. Since the device performance of NEMS is closely related with the mechanical and flexural properties of the material in NEMS, analysis of the mechanical and flexural properties such as intrinsic tensile stress and Young's modulus is a crucial factor for designing the NEMS structures. In the present work, the intrinsic mechanical properties of highly stressed silicon nitride (SiN) beams are investigated as a function of the beam length using two different techniques: (i) dynamic flexural measurement using optical interferometry and (ii) quasi-static flexural measurement using atomic force microscopy. The reliability of the results is analysed by comparing the results from the two different measurement techniques. In addition, the mass density, Young's modulus and internal stress of the SiN beams are estimated by combining the techniques, and the prospect of SiN based NEMS for application in high sensitive mass sensors is discussed.

• Journal of the Korean Ceramic Society
• /
• v.47 no.1
• /
• pp.54-60
• /
• 2010

This paper shortly reviews our recent work on filled skutterudites, which are considered to be one of the most promising thermoelectric (TE) materials due to their excellent power factors and relatively low thermal conductivities. The filled skutterudite system also provides a platform for studying void filling physics/chemistry in compounds with intrinsic lattice voids. By using ab initio calculations and thermodynamic analysis, our group has made progresses in understanding the filling fraction limit (FFL) for single fillers in $CoSb_3$, and ultra-high FFLs in a few alkali-metal-filled $CoSb_3$ have been predicted and then been confirmed experimentally. FFLs in multiple-element-filled $CoSb_3$ are also investigated and anonymous filling behavior is found in a few specific systems. The calculated and measured FFLs, in both single and multiple-filled $CoSb_3$ systems, show good accordance so far. The thermal transport properties can be understood qualitatively by a phonon resonance scattering model, and it seems that a scaling rule may exist between the lattice thermal resistivity and the resonance frequency of filler atoms in filled system. Even though a few things become clear now, there are still many unsolved issues that call for further work.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.66-69
• /
• 2016

In this paper, we suggests a Ka-band LNB considering next-generation UHD satellite TVRO. Since Ka-band has grater attenuation than Ku-band in atmosphere, we designed the low-noise down-converter to improve receiving sensitivity and to extend a dynamic range of receiver. It aims to compensate a quality of ultra high definition transmission signal for rainfall. The low-noise block diagram consists of a three-staged amplifier (LNA), band-pass filter for deleting image (BPF), mixer and IF when considering nonlinear characteristics in the receiver RF front end module. Also, we showed a LNB through optimization processes affecting dynamic range directly in receiver FEM. Asa resuly of experiment, the gain of low-noise down-converter show between 58.5dB and 60.7dB, the noise figure has a high characteristic as 1.38dB. Finally, the phase noise of local oscillator is -63.10dBc at 100MHz offset frequency.