• KEPCO Journal on Electric Power and Energy
• /
• v.8 no.2
• /
• pp.103-110
• /
• 2022

Ultrafine Particle number and size distributions were simultaneously measured at rural area around the power plant in Dangjin, South Korea. New Particle formation and growth events were frequently observed during January, 2021 and classified based on their strength and persistence as well as the variation in geometric mean diameter(GMD) on January 12, 21 and 17. In this study, we investigated mechanisms of new particle growth based on measurements using a high resolution time of flight aerosol mass spectrometer(HR-ToF-AMS) and a scanning mobility particle sizer(SMPS). On Event days(Jan 12 and 21), the total average growth rate was found to be 8.46 nm/h~24.76 nm/hr. These growth rate are comparable to those reported for other urban and rural sites in South Korea using different method. Comparing to the Non-Event day(Jan 17), New Particle Growth mostly occurred when solar radiation is peaked and relative humidity is low in daytime, moreover enhanced under the condition of higher precusors, NO₂ (39.9 vs 6.2ppb), VOCs(129.5 vs 84.6ppb), NH₃(11 vs 4.7ppb). The HR-ToF-AMS PM_1.0 composition shows Organic and Ammoniated nitrate were dominant species effected by emission source in domestic. On the other hand, The Fraction of Ammoniated sulfate was calculated to be approximately 16% and 31% when air quality is inflow from China. Longer term studies are needed to help resolve the relative contributions of each precusor species on new particle growth characteristics.

• Advances in concrete construction
• /
• v.15 no.3
• /
• pp.161-170
• /
• 2023

Ultra-high-performance concrete (UHPC) is produced using high amount of cementitious materials, very low water/cementitious materials ratio, fine-sized fillers, and steel fibers. Due to the dense microstructure of UHPC, it possesses very high strength, elasticity, and durability. Besides that, the UHPC exhibits high ductility and fracture toughness due to presence of fibers in its matrix. While the high ductility of UHPC allows it to undergo high strain/deflection before failure, the high fracture toughness of UHPC greatly enhances its capacity to absorb impact energy without allowing the formation of severe cracking or penetration by the impactor. These advantages with UHPC make it a suitable material for construction of the structural members subjected to special loading conditions. In this research work, the UHPC mixtures having three different dosages of steel fibers (2%, 4% and 6% by weight corresponding to 0.67%, 1.33% and 2% by volume) were characterized in terms of their mechanical properties including facture toughness, before using these concrete mixtures for casting the slab specimens, which were tested under high-energy impact loading with the help of a drop-weight impact test setup. The effect of fiber content on the impact energy absorption capacity and central deflection of the slab specimens were investigated and the equations correlating fiber content with the energy absorption capacity and central deflection were obtained with high degrees of fit. Finite element modeling (FEM) was performed to simulate the behavior of the slabs under impact loading. The FEM results were found to be in good agreement with their corresponding experimentally generated results.

• Fashion & Textile Research Journal
• /
• v.25 no.1
• /
• pp.82-91
• /
• 2023

The children who are part of this study are compelled to wear masks at educational facilities for an extended period of time as they continue to be exposed to Asian dust, fine dust, and COVID-19. However, use of masks is currently causing them a lot of inconvenience. This study aimed to gather basic data for the development of a mask that is suitable and comfortable for children to wear. A total of 331 children aged 1 to 9 were investigated through their parents in terms of their lifestyle, mask wearing and purchasing status, mask preferences, mask inconvenience, and mask improvement. According to the survey on mask use, the proportion of children aged 1-3 years old and wearing ultra-small/XS masks, 4-6 year olds wearing small/S, and 7-9 year olds wearing small/S was the highest. More than 80% of children were wearing masks with a standard filter of KF80 or higher. The purchase criteria for children's masks were found to be excellent in terms of wearing comfort and meeting the filter standards. According to the survey on inconvenience of wearing masks, the majority of those surveyed expressed the need to develop children's masks of different sizes. Furthermore, they experienced various kinds of inconveniences from adult masks, such as the material quality and length of earring bands; it was deduced that these aspects need to be taken care of. The vertical folding type was the most popular in the mask design for children. Children have to wear masks for a prolonged period of time, but they are experiencing lot of inconvenience, which need to be addressed.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.48-54
• /
• 2023

In this study, an injection mold with ultra-small surface properties was manufactured using nanosecond laser processing. A superhydrophobic characteristic analysis was performed on the PET specimen manufactured through this. To this end, a hydrophobic pattern was defined using the Cassie-Baxter model. The defined features were selected with a spot diameter of 25um and pitch spacing of 30um and 35um. As a result of the basic experiment, it was confirmed that the fine pattern shape had an aspect ratio of 1:1 when the pitch interval was 35um and 20 iterations. Through the determined processing conditions, a hydrophobic pattern was implemented on the core surface of KP4. A specimen with a hydrophobic pattern was produced through injection molding. The height of the molded hydrophobic pattern is 20 ㎛ less than the depth of the core and the contact angle measurement results are 92.1°. This is a contact angle smaller than the superhydrophobic criterion. Molding analysis was performed to analyze the cause of this, and it was analyzed that the molding was not molded due to the lack of pressure in the injection machine.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.8-14
• /
• 2023

In this study, basic research was conducted on manufacturing technology of thick-walled light guide a component that controls the light source of automobile lamps. As a preliminary study for manufacturing the final injection molded parts, a model for analyzing the influence of micro patterns on light guides is presented. The optical characteristics of the light guide were analyzed according to the change of the curvature radius of the micro-optical pattern, and the injection molding characteristics of the light guide according to the change of injection molding conditions were analytically evaluated. It was confirmed that the luminance uniformity improves as the R value decreases for changes in the micro-pattern R value, but it was confirmed that there are technical limitations in actual injection mold core processing and high-replication injection molding. Injection molding analysis showed that cooling channel design is very important compared to general injection molding due to thick-wall characteristics and thickness variation. It was also confirmed that the cooling channel has a great influence on the cycle time and birefringence result due to residual stress. As a result of analyzing the influence of filling time, holding condition, and cooling on shrinkage, it was found that the cooling water temperature has a significant effect on the shrinkage of ultra-fine light guide parts, and the holding condition also has a significant effect.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.618-625
• /
• 2018

With the passing of time, exposed concrete structures are affected by a range of environmental, chemical, and physical factors. These factors seep into the concrete and have a deleterious influence compared to the initial performance. The importance of identifying and preventing further performance degradation due to the occurrence of deterioration has been greatly emphasized. In recent years, evaluations of the target life have attracted increasing interest. During the freezing-melting effect, a part of the concrete undergoes swelling and shrinking repeatedly. At these times, chloride ions present in seawater penetrate into the concrete, and accelerate the deterioration due to the corrosion of reinforced bars in the concrete structures. For that reason, concrete structures located onshore with a freezing-melting effect are more prone to this type of deterioration than inland structures. The aim of this study was to develop a high performance mortar mixed with a mineral admixture for the durability properties of concrete structures near sea water. In addition, experimental studies were carried out on the strength and durability of mortar. The mixing ratio of the silica fume and meta kaolin was 3, 7 and 10 %, respectively. Furthermore, the ultra-fine fly ash was mixed at 5, 10, 15, and 20%. The mortar specimens prepared by mixing the admixtures were subjected to a static strength test on the 1st and 28th days of age and degradation acceleration tests, such as the chloride ion penetration resistance test, sulfuric acid resistance test, and salt resistant test, were carried out at 28 days of age. The chloride diffusion coefficient was calculated from a series of rapid chloride penetration tests, and used to estimate the life time against corrosion due to chloride ion penetration according to the KCI, ACI, and FIB codes. The life time of mortar with 10% meta kaolin was the longest with a service life of approximately 470 years according to the KCI code.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.94-100
• /
• 2011

Purpose: Basal/Acetazolamide-challenged brain perfusion SPECT is very useful to assess cerebral perfusion and vascular reserve. However, as there is a trade off between sensitivity and spatial resolution in the selection of collimator, the selection of optimal collimator is crucial. In this study, we examined three collimators to select optimal one for 1-day brain perfusion SPECT. Materials and Methods: Three collimators, low energy high resolution-parallel beam (LEHR-par), ultra resolution-fan beam (LEUR-fan) and super fine-fan beam (LESFR-fan), were tested for 1-day imaging using Triad XLT 9 (TRIONIX). The SPECT images of Hoffman 3D brain phantom filled with 99mTc of 170 MBq and a normal volunteer were acquired with a protocol of 50 kcts/frame and detector rotation of 3 degree. Filterd backprojection (FBP) reconstruction with Butterworth filter (cut off frequencies, 0.3 to 0.5) was performed. The quantitative and qualitative assessments for three collimators were performed. Results: The blind tests showed that LESFR-fan provided the best image quality for Hoffman brain phantom and the volunteer. However, images for all the collimator were evaluated as 'acceptable'. On the other hand, in order to meet the equivalent signal-to-noise ratio (SNR), total acquisition time or radioactivity dose for LESFR-fan must have been increased up to almost twice of that for LEUR-fan and LEHR-par. The volunteer test indicated that total acquisition time could be reduced approximately by 10 to 14 min in clinical practice using LEUR-fan and LEHR-par without significant loss on image quality, in comparison with LESFR-fan. Conclusion: Although LESFR-fan provides the best image quality, it requires significantly more acquisition time than LEUR-fan and LEHR-par to provide reasonable SNR. Since there is no significant clinical difference between three collimators, LEUR-fan and LEHR-par can be recommended as optimal collimators for 1-day brain perfusion imaging with respect to image quality and SNR.

• Resources Recycling
• /
• v.9 no.4
• /
• pp.16-27
• /
• 2000

In order to produce raw material powder of advanced magnetic material by spray roasting process, newly modified spray roasting system was developed in this work. In this spray roasting system, raw material solution was effectively atomized and sprayed into the reaction furnace. Also, uniform temperature distribution inside reaction furnace made thermal decomposition process fully completed, and produced powder was effectively collected in cyclone and bag filter. This system equipped with apparatus which can purify hazard produced gas. In this study complex acid solution was prepared by dissolution of mill scale and ferro-Mn into the acid solution, and the pH of this complex acid solution was controlled about to 4. It was conformed that mill scale and ferro-Mn containing a lot of impurities such as $SiO_2$, P and Al could be used as raw material by reducing the impurities content of complex acid solution below 20 ppm. Complex oxide powder of Fe-Mn system was produced by spraying purified complex acid solution into the spray roaster through nozzle, and the variations of produced powder characters were studied by changing he reaction conditions such as reaction temperature, the injection velocity of solution and air, nozzle tip size and concentration of solution. The morphology of produced powder had spherical shape under the most experimental conditions, and concentration of solution. The morphology of produced powder has spherical shape under the most experimental conditions, and the composition and the particle size distribution were almost uniform, which tells the excellence of this spray roasting system. The grain size of most produced powder was below 100 nm. From the above results, it will be possible to produce ultra fine oxide powder from the chloride of Fe, Mn, Ni, Cu and rare earth by using this spray roasting system, and also to produce ultra fine pure metal powder by changing reaction atmosphere.

• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.217-225
• /
• 2004

This study was carried out to reduce the loss of frozen dough quality during frozen storage. Using response surface method, ascorbic acid 160.4 ppm, L-cysteine 63.1 ppm, and SSL 0.6% were found to be optimum, with xanthan gum 0.3% (formula A) and Ultra tex-3 5% (formula B) added as cryoprotectants. During frozen storage at $-20^{\circ}C$, control rapidly deteriorated after 4 weeks, while formulas A and B showed slight deterioration with immutable quality after 10 weeks.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.22-35
• /
• 2021

Recently, as the climate changes rapidly and the prevalence of airborne fine particulate matter increases, the pattern of pollutants in the atmospheric environment is also changing. Therefore, the importance of studying the stability of pigments used in colored cultural properties is emerging. Hoecheong is an inorganic blue glass pigment called smalt; it is made by using cobalt as a coloring element in potash glass, and was widely used in colored cultural assets, such as murals and paintings. In this study, we collected three other hoecheong pigments to analyze their properties. The percentage of Co and K contained are different according to the manufacturer, and the smalt-3 sample has a lower cobalt content (15.1 wt.%) and higher potassium content (29.6 wt.%). After this analysis, colored specimens were prepared. Prepared specimens were exposed to ultra-violet rays, CO₂/NO₂, and NaCl, which are known to have the greatest influence on the stability of pigments. We found that factors affecting the color stability were NO₂ gas, ultra-violet rays, and water-soluble salts (NaCl). Among them, NO₂ has the most severe impact on color change of the pigments. Results of the component analysis showed that the color change depends on the potassium and cobalt content of the hoecheong pigment. Among the specimens, smalt-3 showed the most vulnerability after exposure to NO₂ gas and water-soluble salts. Pigment film stability is affected by watersoluble salts, giving rise not only to color change, but also weakening the physical properties of the film. However, there was no significant change in composition and color after exposure to CO₂ gas. In conclusion, we found that hoecheong pigments underwent color change and increased instability of the coating film when exposed to any of the atmospheric environmental factors used in this study, except for CO₂.