• 정보와 통신
• /
• 제28권11호
• /
• pp.49-55
• /
• 2011

무선센서네트워크를 위한 무선센서노드는 한정된 전력원을 이용하여 수천에서 수만시간의 동작을 가능하게 해야하므로 초저전력 (Ultra Low Power: ULP) 소모가 매우 중요한 설계 요구조건이 된다. 이를 위해 센서노드의 동작 주기(Duty Cycling)를 제어하는 기법이 전체 전력소모를 줄이는 매우 중요한 기술로 사용되고 있다. 회로의 전력 소모 감소를 위한 몇 가지 중요한 기술에는 회로적으로는 전류 재사용기술과 송수선기 구조로는 Super-regenerative 구조와 On-Off Keying 송수신기 구조가 있다. 또한 ULP Radio가 휴면모드에도 Wake-up을 가능하게 하기 위해서는 초저전력 클락 발생기 회로가 1${\mu}W$이하의 전력소모로 구현할 수 있어야 한다. 이러한 사항들을 적절히 고려함으로써 초저전력 CMOS Radio를 구현할 수 있다.

• 한국진공학회지
• /
• 제8권4A호
• /
• pp.397-402
• /
• 1999

The base pressure of the vacuum vessel of KSTAR tokamak is to be ultra high vacuum, $10^{-6}\sim10^{-7}Pa$, to produce a clean plasma with low impurity concentrations. For this purpose, vessel and plasma facing components need to be baked up to $250^{\circ}C$, $350^{\circ}C$ respectively to remove impurities from the plasma-material interaction surfaces. Here the required heating power to be supplied for baking has been calculated according to pre-assumed different temperature profiles (baking scenario and proper baking plan for KSTAR tokamak has been proposed. Mass flow rate and temperature of nitrogen gas for baking has also been calculated.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.539-540
• /
• 2008

This paper presents an ultra-wideband (UWB) CMOS low noise amplifier (LNA) topology that operates in 3.1-10.6GHz band. The common gate structure provides wideband input matching and flattens the passband gain. The proposed UWB amplifier is implemented in 0.18 um CMOS technology for lower band operation mode. Simulation shows a minimum NF of 2.35 dB, a power gain of $18.3{\sim}20\;dB$, better than -10 dB of input and output matching, while consuming 16.4 mW.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권6호
• /
• pp.754-759
• /
• 2016

A transformer feedback low-noise amplifier (LNA) is implemented in a standard $0.18{\mu}m$ CMOS process, which exploits drain-to-gate transformer feedback technique for wideband input matching and operates across entire 3~5 GHz ultra-wideband (UWB). The proposed LNA achieves power gain above 9.5 dB, input return loss less than 15.0 dB, and noise figure below 4.8 dB, while consuming 8.1 mW from a 1.8-V supply. To the authors' knowledge, drain-to-gate transformer feedback for wideband input matching cascode LNA is the first adopted technique for UWB application.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.214-216
• /
• 2005

The PAL (Pohang Accelerator Laboratory) is persuading to construct a SASE-XFEL facility (PAL XFEL) that supplies coherent X-rays. The bright and stable electron beam is essential for the PAL XEL. The electron beams has to have an emittance of 1.0 mm-mrad, a peak current of 3 kA, and a low energy spread of 1.0 MeV. In order to provide reasonably stable SASE output, the RF stability of 0.02% rms is required for both RF phase and amplitude. This is a technologically challenging issue for PAL XFEL. An inverter technology is to be applied to charge the PFN of a new modulator. Therefore, a new inverter system should provide very stable charging performances. This paper presents the development of an ultra stable klystron-modulator with an inverter power supply.

• 한국정보통신학회논문지
• /
• 제8권1호
• /
• pp.220-226
• /
• 2004

UWB 통신은 높은 전송속도와 저전력 통신이 가능하다는 이유로 최근에 매우 각광을 받는 통신 응용분야이다. 따라서, 다양한 UWB 통신 기술의 적용을 위하여 UWB 신호의 특성과 변조 방법을 연구하는 것은 매우 중요하다. 본 논문에서는 UWB 통신에 사용 가능한 가우시언 모노펄스의 특성을 분석하고 PPM 변조 방법과 PAM 변조방법의 성능을 비교하였다. 또한 다양한 UWB 통신 환경에서의 중심 주파수가 다른 QPSK 시스템의 간섭 효과를 분석하였으며 간단한 UWB 송수신 시스템을 시뮬레이션 하였다.

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 2010년도 한국컴퓨터종합학술대회논문집 Vol.37 No.1(D)
• /
• pp.170-173
• /
• 2010

최근 진보된 무선 통신 기술과 발전된 의료 기술로 인하여 u-Health의 핵심 기술인 WBAN에 대한 연구가 활발히 진행되고 있다. 인체에 이식 가능한 WBAN 장치는 전원 공급에 제한이 있으므로 소비전력을 최소화하기 위한 MAC 프로토콜이 필요하다. 본 논문은 WBAN 장치의 다양한 무선 통신 특성을 적용한 시뮬레이터에 관한 것으로 MICS 대역의 채널 특성을 적용하였고, 데이터의 신뢰성과 에너지 효율성을 향상시키기 위해 가변 패킷 및 비트맵 기반의 패킷 블록 전송기법을 적용한 MAC 프로토콜을 사용한다.

• Progress in Superconductivity
• /
• 제9권2호
• /
• pp.157-161
• /
• 2008

Due to high speed operations and ultra low power consumptions RSFQ logic circuit is a very good candidate for future electronic device. The focus of the RSFQ circuit development has been on the advancement of analog-to-digital converters and microprocessors. Recent works on RSFQ ALU development showed the successful operation of an 1-bit block of ALU at 40 GHz. Recently, the study of an RSFQ analog-to-digital converter has been extended to the development of a single chip RF digital receiver. Compared to the voltage logic circuits, RSFQ circuits operate based on the pulse logic. This naturally leads the circuit structure of RSFQ circuit to be pipelined. Delay time on each pipelined stage determines the ultimate operating speed of the circuit. In simulations, a two junction Josephson transmission line's delay time was about 10 ps, a splitter's 14.5 ps, a switch's 13 ps, a half adder's 67 ps. Optimization of the 4-bit ALU circuit has been made with delay time consideration to operate comfortably at 10 GHz or above.

• Journal of Welding and Joining
• /
• 제31권4호
• /
• pp.17-22
• /
• 2013

The excellent beam quality of high power fiber lasers are commonly used for remote welding applications in body job applications. The Welding speed and productivity is unmatched with any other welding technology including resistance spot welding or traditional laser welding. High tooling cost for clamping and bulky safety enclosures are obstacles which are limiting the use. With the newly developed Laser stitch welding gun we have an integrated clamping in the process tool and the laser welding is shielded in a way that no external enclosure is needed. Operation of this laser welding gun is comparable with resistance spot welding but 2-times faster. Laser stitch welding is faster than spot welding and slower than remote welding. It is a laser welding tool with all the laser benefits like welding of short flanges, weld ability of Ultra High Strength steel, 3 layers welding and Aluminium welding. Together with low energy consumption and minimum operation cost of IPG fiber laser it is a new and sharp tool for economic car body assembly.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -3
• /
• pp.1398-1400
• /
• 2002

A new PLF-BLU (Plastic Light Fiber-Back Light Unit) using side glowing light fiber rods array for the 42" LCD TV display has been evelopedd. The light fibers were 14mm in diameter and 50cm long pure transparent acrylic rods of 1.49 refractive index. Fine seratees were made on the flat side of rod. extremely bright incandscent light from lamp fed into the fiber si scattered at scratches then emerges through the surface of rod. A typical PLF-BLU system consists of 24 PLFs produced side glow of brightness of 4,500cd/㎡ to 6,500cd/㎡. New PLF-BLU is proved to be a BLU of rigid, bright, no heat generation, and low power consumption, hence a prospective BLU system for very and/or ultra large size TVs. A new LED-PLF-BLU system considered to be a revolutionary to break-through of the BLU technologies has also been developed, and is decribed briefly.