• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• 한국지반공학회논문집
• /
• 제21권2호
• /
• pp.113-120
• /
• 2005

수평하중을 받는 현장타설말뚝을 합리적이고 경제적으로 설계하기 위해서 가장 중요한 것은 지구조 사이의 상호작용을 이해하는 것이다. 그러나 지난 수십년 동안 수평하중을 받는 깊은 기초의 거동에 대한 많은 연구가 있었음에도 불구하고, 문제의 성격상 삼차원적이며 비대칭성으로 인하여 더해지는 지반고유의 비선형성, 불균일성, 복잡성 때문에 극한수평지지력을 공식화하기란 매우 어렵다 본 연구에서는 특정한 현장조건, 기초의 기하학적 특성(D/B비),하중조건 등에 따른 많은 설계 방법들 중에서 가장 널리 알려진 네 가지의 방법(즉, Reese, Broms, Hansen, 그리고 Davidson)에 대해서 재검토하였다. 그리고 본 연구의 밀환으로 행한 모형실험으로 얻어진 하중-변위곡선을 쌍곡선으로 변환하여 해석된 방곡선수평지지력(H$_h$)과 위의 네 가지 방법들에 의하여 예측되는 극한수평지지력(H$_u$)을 비교하였다. Reese와 Hansen의 방법에 의해 구한 H$_u$ / H$_h$비는 각각 0.966와 1.015로서 실험결과와 매우 근사한 극한수평지지력을 제시하고 있다. 반면에 Davidson의 방법에 의해 구한 H$_u$는 에 비하여 $30\%$ 가량 큰 것으로 예측하고 있으나 네 가지 방법중에서 예측 수평지지력값에 대한 C.O.V.가 가장 작다. 네 가지 방법 중 가장 단순한 Broms의 방법은 H$_u$/ H$_h$: 0.896으로서 네 방법 중에서 극한 수평지지력을 가장 작게 평가하는 것으로 나타나지만 극한수평지지력값을 예측함에 있어서 가장 작은 S.D.를 보인다. 결론적으로, 네 가지의 방법 중 그 어 것도 극한수평지지력을 정확하게 예측한다는 면에서 다른 방법보다 더 우수하다고 할 수는 없다. 또한, 계산과정이 얼마나 정교하거나 복잡한 것과는 상관없이 극한수평지지력을 예측하는데 있어서 신뢰도는 또 다론 문제인 것 같다.

• 한국강구조학회 논문집
• /
• 제8권4호통권29호
• /
• pp.85-94
• /
• 1996

This paper investigated structural behaviors of joint of concrete filled steel tube column and P.C reinforced concrete beam through a series of hysteretic behavior experiment. The results are summarised as follows: (1) The joint stiffness of concrete filled square steel tube column and P.C reinforecd beam was higher than that of concrete filled circular steel tube column and P.C reinforecd beam, and it was decreased as the increase of the number of hysteretic cycle. (2) The aspects of the hysteretic behavior in the joint was stable as the increase of the number of hysteretic cycle, and rotation resisting capacity of joint of concrete filled square steel tube column and P.C reinforced concrete beam was higher than those of the concrete filled circular steel tube column and P.C reinforced concrete beam. (3) Some restriction must be put upon the ratio of axial force in this joint model because the load carrying capacity was decreased by flexural and flexural-torsional buckling in case of the ratio of axial force 0.6. (4) The emprical formula to predict the ultimate capacity of joint model to superimpose shearing strength of steel web(H section) and bending strength of reinforced concrete beam was expected.

• Steel and Composite Structures
• /
• 제8권1호
• /
• pp.53-83
• /
• 2008

A rational and efficient seismic design methodology for irregular space steel frames using advanced methods of analysis in the framework of Eurocodes 8 and 3 is presented. This design methodology employs an advanced static or dynamic finite element method of analysis that takes into account geometrical and material non-linearities and member and frame imperfections. The inelastic static analysis (pushover) is employed with multimodal load along the height of the building combining the first few modes. The inelastic dynamic method in the time domain is employed with accelerograms taken from real earthquakes scaled so as to be compatible with the elastic design spectrum of Eurocode 8. The design procedure starts with assumed member sections, continues with the checking of the damage and ultimate limit states requirements, the serviceability requirements and ends with the adjustment of member sizes. Thus it can sufficiently capture the limit states of displacements, rotations, strength, stability and damage of the structure and its individual members so that separate member capacity checks through the interaction equations of Eurocode 3 or the usage of the conservative and crude q-factor suggested in Eurocode 8 are not required. Two numerical examples dealing with the seismic design of irregular space steel moment resisting frames are presented to illustrate the proposed method and demonstrate its advantages. The first considers a seven storey geometrically regular frame with in-plan eccentricities, while the second a six storey frame with a setback.

• Structural Engineering and Mechanics
• /
• 제50권5호
• /
• pp.617-633
• /
• 2014

Because the elevated temperature degrades the mechanical properties of materials used in containments, the global behavior of containments subjected to the internal pressure under high temperature is remarkably different from that subjected to the internal pressure only. This paper concentrates on the nonlinear finite element analyses of the nuclear power plant containment structures, and the importance for the consideration of the elevated temperature effect has been emphasized because severe accident usually accompanies internal high pressure together with a high temperature increase. In addition to the consideration of nonlinear effects in the containment structure such as the tension stiffening and bond-slip effects, the change in material properties under elevated temperature is also taken into account. This paper, accordingly, focuses on the three-dimensional nonlinear analyses with thermal effects. Upon the comparison of experiment data with numerical results for the SNL 1/4 PCCV tested by internal pressure only, three-dimensional analyses for the same structure have been performed by considering internal pressure and temperature loadings designed for two kinds of severe accidents of Saturated Station Condition (SSC) and Station Black-out Scenario (SBO). Through the difference in the structural behavior of containment structures according to the addition of temperature loading, the importance of elevated temperature effect on the ultimate resisting capacity of PCCV has been emphasized.

• 콘크리트학회논문집
• /
• 제16권6호
• /
• pp.733-740
• /
• 2004

본 논문에서는 휨과 비틀림을 함께 받는 전형적인 건축분야의 프리캐스트 프리스트레스트 콘크리트 역T형 보와 직사각형 보의 거동을 연구하였다. 연구 목적을 위하여 국내 건축시장에서 사용되고 있는 주차장 활하중 $5 kN/m^2$ 및 상가 활하중 $12 kN/m^2$ 의 역T형 프리캐스트 프리스트레스트 콘크리트 보를 제작하였다. 또한 같은 길이의 보 밑면과 면적을 갖는 두개의 직사각형 콘크리트 보도 제작하였다. 따라서 설계 활하중과 단면형상이 다른 네 개의 보를 휭과 비틀림의 동시 작용 하에서 실험하여 그 결과를 분석하고 비교하였다. 실험결과 비틀림의 영향으로 시험체 모두 초기 균열 및 극한 휨의 강도가 저하되었다. 그러나 단면형상에 따라 사용하중 및 극한 하중 하에서의 하중 지지력에는 커다란 차이가 없는 것으로 나타났다.

• Earthquakes and Structures
• /
• 제18권6호
• /
• pp.677-689
• /
• 2020

A building structural system of moment resisting frame (MRF) with concrete filled steel tubular (CFST) columns and wide flange H beams, is one of the most conveniently constructed structural systems. However, there were few studies on evaluating seismic performance of full-scale CFST columns under high axial compression. In addition, some existing famous design codes propose various limits of width-to-thickness ratio (B/t) for steel tubes of the ductile CFST composite members. This study was intended to investigate the seismic behavior of CFST columns under high axial load compression. Four full-scale square CFST column specimens with a B/t of 42 were carried out that were subjected to horizontal cyclic-reversal loads combined with constantly light, medium and high axial loads and with a linearly varied axial load, respectively. Test results revealed that shear strength and deformation capacity of the columns significantly decreased when the axial compression exceeded 0.35 times the nominal compression strength of a CFST column, P₀. It was obvious that the higher the axial compression, the lower both the shear strength and deformation capacities were, and the earlier and faster the shear strength degradation occurred. It was found as well that higher axial compressions resulted in larger initial lateral stiffness and faster degradation of post-yield lateral stiffness. Meanwhile, the lower axial compressions led to better energy dissipation capacities with larger cumulative energy. Moreover, the study implied that under axial compressions greater than 0.35P₀, the CFST column specimens with B/t limits recommended by AISC 360 (2016), ACI 318 (2014), AIJ (2008) and EC4 (2004) codes do not provide ultimate interstory drift ratio of more than 3% radian, and only the limit in ACI 318 (2014) code satisfies this requirement when axial compression does not exceed 0.35P₀.

• Computers and Concrete
• /
• 제32권4호
• /
• pp.351-363
• /
• 2023

Reducing the self-weight of reinforced concrete structures problem is discussed in this paper by using two types of self-weight reduction, the first is by using lightweight coarse aggregate (crushed brick) and the second is by using styropor block. Experimental and Numerical studies are conducted on (LWAC) lightweight aggregate reinforced concrete slabs, having styropor blocks with various sizes of blocks and the ratio of shear span to the effective depth (a/d). The experimental part included testing eleven lightweight concrete one-way simply supported slabs, comprising three as reference slabs (solid slabs) and eight as styropor block slabs (SBS) with a total reduction in cross-sectional area of (43.3% and 49.7%) were considered. The holes were formed by placing styropor at the ineffective concrete zones in resisting the tensile stresses. The length, width, and thickness of specimen dimensions were 1.1 m, 0.6 m, and 0.12 m respectively, except one specimen had a depth of 85 mm (which has a cross-sectional area equal to styropor block slab with a weight reduction of 49.7%). Two shear spans to effective depth ratios (a/d) of (3.125) for load case (A) and (a/d) of (2) for load case (B), (two-line monotonic loads) are considered. The test results showed under loading cases A and B (using minimum shear reinforcement and the reduction in cross-sectional area of styropor block slab by 29.1%) caused an increase in strength capacity by 60.4% and 54.6 % compared to the lightweight reference slab. Also, the best percentage of reduction in cross-sectional area is found to be 49.7%. Numerically, the computer program named (ANSYS) was used to study the behavior of these reinforced concrete slabs by using the finite element method. The results show acceptable agreement with the experimental test results. The average difference between experimental and numerical results is found to be (11.06%) in ultimate strength and (5.33%) in ultimate deflection.

• 대한토목학회논문집
• /
• 제33권3호
• /
• pp.889-900
• /
• 2013

대형 구조물의 기초나 지중 구조물 시공을 위한 대규모 굴착 시 매우 큰 토압이 발생할 수 있다. 이러한 큰 토압을 지지하기 위해 기존에 사용되어 온 강재 버팀보를 적용할 경우 경제성 및 효율성이 저하될 우려가 있다. 이러한 점을 개선하기 위해 PCT(Precast Concrete Truss) 시스템을 고안하였으며 이에 대한 실험 및 해석적 연구를 수행하였다. 콘크리트 트러스 부재의 조립 및 해체를 용이하게 하기 위해 적절한 연결방법이 제안되었다. 이러한 연결부를 포함한 PCT 시스템의 내하력을 검증하기 위해 실대형 실험이 실시되었으며, 실험결과는 구조해석결과와도 비교되었다. PCT 버팀보를 모사한 시험체는 극한하중 도달 시까지 좌굴이 발생하지 않았으나, 연결 부재 상세에 대한 일부 개선점이 도출되었다. PCT 시스템은 대규모 굴착 시 기존의 강재 버팀보를 대체하는 가설구조물로서 효율적으로 활용될 수 있을 것으로 기대된다.

• 한국전산구조공학회논문집
• /
• 제28권1호
• /
• pp.101-113
• /
• 2015

이 논문은 화재에 노출된 철근콘크리트 구조에 대한 수치해석 모델을 제시하고, 기존의 자료 및 설계 규준과의 비교를 통해 구조물의 설계 시 고려 사항에 대해 제안하고 있다. 수치해석은 비정상 열전달 해석과 비선형 구조해석의 두 단계로 수행되며, 비정상 열전달 해석을 통해서 얻어진 화재시간에 따른 단면 온도분포를 바탕으로 비선형 구조해석하여 부재의 상태에 대한 정보를 얻게 된다. 이때, 철근콘크리트의 재료모델을 화재진행상태(Under-Fire)와 화재종료 후 냉각상태(After-Cooling)로 나뉘어 해석수행하여 각각의 재료상태에 따른 거동의 변화를 살펴본다. 해석된 결과는 여러 구조물에 대해 기존의 실험결과와 비교하여 검증하고, 설계 규준과의 비교를 통해 화재 시 구조물의 안전성에 대해 고찰하였다.