• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.527-528
• /
• 2006

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1847-1850
• /
• 2008

The process conditions during ultraviolet nanoimprint lithography (UV-NIL) process such as temperature, stamping pressure, UV irradiation, etc. are effective factors for successful imprinting of complex and fine patterns. In this study, the effects of aluminum mold on the thermal characteristics of UV-NIL process were investigated through imprinting experiments and numerical simulations. The temperature of polymer resin on mold was measured to study thermal characteristics during UV curing. From the experimental and numerical results, the importance of curing reaction control for UV-NIL process was discussed for deformation characteristics.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.167-170
• /
• 2005

The two-dimensional (2D) and three-dimensional (3D) diamond-like carbon (DLC) stamps for ultraviolet nanoimprint lithography (UV-NIL) were fabricated using two kinds of methods, which were a DLC coating process followed by the focused ion beam (FIB) lithography and the two-photon polymerization (TPP) patterning followed by nano-scale thick DLC coating. We fabricated 70 nm deep lines with a width of 100 nm and 70 nm deep lines with a width of 150 nm on 100 nm thick DLC layers coated on quartz substrates using the FIB lithography. 200 nm wide lines, 3D rings with a diameter of $1.35\;{\mu}m$ and a height of $1.97\;{\mu}m$, and a 3D cone with a bottom diameter of $2.88\;{\mu}m$ and a height of $1.97\;{\mu}m$ were successfully fabricated using the TPP patterning and DLC coating process. The wafers were successfully printed on an UV-NIL using the DLC stamp. We could see the excellent correlation between the dimensions of features of stamp and the corresponding imprinted features.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.11-15
• /
• 2018

In this study, we deposited silver nanoparticles on the nanocone array structure which was fabricated by the UV nanoimprint process for optical signal amplification. The deposition of the silver nanoparticles was based on the evaporation behavior of the solution droplet according to wettability of surface and the deposition pattern changed from the center of the droplet to the edge depending on the difference of thermal energy. The optical property of silver nanoparticles that were deposited on imprinted nanohole patterns was simulated by the Finite difference time domain (FDTD) analysis method, and it was confirmed that energy was concentrated around the silver nanoparticle of the finally fabricated structure.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.79-84
• /
• 2013

Nanoimprint lithography (NIL) is the next generation photolithography process in which the photoresist is dispensed onto the substrate in its liquid form and then imprinted and cured into a desired pattern instead of using traditional optical system. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. Although one of the current major research trends of NIL is large-area patterning, the technical difficulties to keep the uniformity of the residual layer become severer as the imprinting area increases more and more. In this paper, with the rolling type imprinting process, a mold, placed upon the $2^{nd}$ generation TFT-LCD glass sized substrate($370{\times}470mm^2$), is rolled by a rubber roller to achieve a uniform residual layer. The prediction of residual layer thickness of the photoresist by rolling of the rubber roller is crucial to design the rolling type imprinting process, determine the rubber roller operation conditions-mpressing force & feeding speed, operate smoothly the following etching process, and so forth. First, using the elasticity theory of contact problem and the empirical equation of rubber hardness, the contact length between rubber roller and mold is calculated with consideration of the shape and hardness of rubber roller and the pressing force to rubber roller. Next, using the squeeze flow theory to photoresist flow, the residual layer thickness of the photoresist is calculated with information of the viscosity and initial layer thickness of photoresist, the shape of mold pattern, feeding speed of rubber roller, and the contact length between rubber roller and mold previously calculated. Last, the effects of rubber roller operation conditions, impressing force & feeding speed, on the residual layer thickness are analyzed with consideration of the shape and hardness of rubber roller.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1917-1921
• /
• 2008

Ultraviolet-nanoimprint lithography (UV-NIL) is promising technology for cost effectively defining micro/nano scale structure at room temperature and low pressure. In addition, this technology is fascinating because of it's possibility for high-throughput patterning without complex processes. However, to acquire good micro/nano patterns using this technology, there are some challenges such as uniformity and fidelity of patterns, etc. In this paper, we have focused on uniform contact mechanism and performed contact mechanics analysis. The dimension of the flexible sheet to get adequate uniform contact area has been obtained from contact mechanics simulation. Based on this analysis, we have made a uniform pressurizing device and confirmed its uniform pressurized zone using a pressure sensing paper.

• Journal of Information Display
• /
• v.11 no.2
• /
• pp.49-51
• /
• 2010

Nanoimprint lithography (NIL) using ultraviolet (UV) rays is a technique in which unconventional lithographic patterns are formed on a substrate by curing a suitable liquid resist in contact with a transparent patterned mold, then releasing the freshly patterned material. Here, various solutions are introduced to achieve sufficient overlay accuracy and to overcome the technical challenges in resist patterning via UV imprinting. Moreover, resist patterning of all the layers in TFT and of the BM layer in CF was carried out using UV imprinting lithography to come up with a 12.1-inch TFT-LCD panel with a resolution of $1280{\times}800$ lines (125 ppi).

• Korean Chemical Engineering Research
• /
• v.45 no.2
• /
• pp.149-154
• /
• 2007

Nanoimprint lithography (NIL) is useful technique because of its low cost and high throughput capability for the fabrication of sub-micrometer patterns which has potential applications in micro-optics, magnetic memory devices, bio sensors, and photonic crystals. Usually, a chemical surface treatment of the stamp is needed to ensure a clean release after imprinting and to protect the expensive original master against contamination. Meanwhile, adhesion promoter between resin and substrate is also important in the nanoscale pattern. In this work, we have investigated the effect of surface treatment using silane coupling agent as release layer and adhesion promoter for UV-Nanoimprint lithography. Uniform SAM (self-assembled monolayer) could be fabricated by vapor deposition method. Vapor phase process eliminates the use of organic solvents and greatly simplifies the handling of the sample. It was also proven that 3-acryloxypropyl methyl dichlorosilane (APMDS) could strongly improve the adhesion force between resin and substrate compared with common planarization layer such as DUV-30J or oxygen plasma treatment.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.65-70
• /
• 2023

Nanoimprint lithography (NIL) has attracted much attention due to its process simplicity, excellent patternability, process scalability, high productivity, and low processing cost for pattern formation. However, the pattern size that can be implemented on metal materials through conventional NIL technologies is generally limited to the micro level. Here, we introduce a novel hard imprint lithography method, extreme-pressure imprint lithography (EPIL), for the direct nano-to-microscale pattern formation on the surfaces of metal substrates with various thicknesses. The EPIL process allows reliable nanoscopic patterning on diverse surfaces, such as polymers, metals, and ceramics, without the use of ultraviolet (UV) light, laser, imprint resist, or electrical pulse. Micro/nano molds fabricated by laser micromachining and conventional photolithography are utilized for the nanopatterning of Al substrates through precise plastic deformation by applying high load or pressure at room temperature. We demonstrate micro/nanoscale pattern formation on the Al substrates with various thicknesses from 20 ㎛ to 100 mm. Moreover, we also show how to obtain controllable pattern structures on the surface of metallic materials via the versatile EPIL technique. We expect that this imprint lithography-based new approach will be applied to other emerging nanofabrication methods for various device applications with complex geometries on the surface of metallic materials.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.521-522
• /
• 2008

An etch-less simple method was developed to fabricate two-dimensional nanostructures on glass substrate directly by using UV curable polymer resin and UV nanoimprint lithography in order to improve output coupling efficiency of OLEDs. OLEDs integrated on nanoimprinted substrates enhanced electro-luminance intensity by up to 50% compared with the conventional device.