• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.255-261
• /
• 2004

Experiments using ozone are presented for the water purification and wine quality improvement. Advanced oxidation process results reveal water treatment by both ozone and UV radiation increases quality of the takju prepared using a Korean conventional nuruk than with ozone-treatment or convectional method only. Water quality was enhanced by ozone treatment, resulting in 85% reduction of hardness, and 30% increase in total glucose produced due to increased conductivity and biodegradability of water. Although initially decreased slightly due to oxidation of takju, higher than expected ethanol production was observed, with ozone plus UV treatment resulting in 20% higher production compared with other methods.

• Journal of environmental and Sanitary engineering
• /
• v.12 no.2
• /
• pp.51-57
• /
• 1997

This work carried out the removal of aniline by wet oxidation in aqueous solutions like a industrial wastewater using Ozone, UV, and Ozone-UV . The main features of this experiment are as follows: the aniline was decomposed by OH and HO$_{2}$ radicals which produced from the reaction of water with UV and Ozone, when the Ozorie and Ozone-UV used the aniline was decomposed completely. The decomposition of aniline was very fast reaction and the reaction times were within 10min. and 20min. in case of for Ozone Ozone-UV respectively. Assumed simplified reaction mechanism from the aniline oxidation model, and the we are calculated the theoretical reaction rate constants by computer simulation, and then compared with experimental data. We suggest that this simulation program is applicable to estimate of the aniline decaying concentration and removal efficiency of aniline - contaminated wastewater.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.617-622
• /
• 2011

Ozone-based advanced oxidation was applied for the treatment of anaerobic digestion effluent of livestock wastewater. Initial COD and color value were 930 mg/L and 0.04, respectively, and the 1/10-diluted wastewater was used for the study. The treatment characteristics were compared between the conventionally generated ozone ($105{\mu}m$) and microbubbled ozone ($13{\mu}m$). The use of microbubbled ozone improved the removal of chemical oxygen demand (COD) and color by 85% and 26%, respectively, compared with the conventionally bubbled ozone. The application of microbubbled $O_3/UV$, $O_3/H_2O_2$, $O_3/UV/H_2O_2$ combinations resulted in 5~10% higher color removal than ozone alone, which implies that the contribution of UV or $H_2O_2$ is not significant in color removal. On the other hand, COD removal could be increased two folds compared with ozone alone through $O_3/UV/H_2O_2$ combination. The contribution of $H_2O_2$ was bigger than UV for COD removal with microbubbled ozone. Due to the enhancement of dissolved ozone and radical activity, the microbubbling enabled us to additional COD removal even after stopping ozone supply in the presence of UV or $H_2O_2$.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.391-396
• /
• 2014

Polymer microneedles can be fabricated by a micromolding method, an easy and cost-effective method. However, it is not easy to achieve uniform coating with an aqueous coating solution due to hydrophobic surface of polymer microneedles. 3-Dimensional coating polymer microneedles could deliver more than twice as much dose as in-plane metal microneedles by increasing coating area and the number of microneedles per unit area. A uniform coating was not obtained by addition of coating additives in the coating solution. The satisfied coating was achieved by treatment of surface of polymer microneedle with metal deposition and UV/ozone, and UV/ozone treatment was an ultimate surface treatment method based on biological safety. Calcein coating polymer microneedles were prepared by using UV/ozone treatment and followed dip-coating, and they delivered calcein in porcine skin successfully after 15 min of insertion.

• Journal of Industrial Technology
• /
• v.26 no.A
• /
• pp.199-205
• /
• 2006

Ozone alone and catalytic ozone processes were introduced for treatment of humic acid, which is representative refractory organic compound. The treatment efficiencies of humic acid in each process were analyzed in pH variation, DOC removal, and $UV_{254}$ decrease. Mn loaded GAC catalyst was prepared by loading potassium permanganate onto the granular activated carbon surface. BCM-GAC and BCM-Silica gel catalyst were prepared by BCM. $UV_{254}$ decrease in all processes was comparatively high with efficiency over 87%. DOC removal in ozone/GAC process was the highest with 78%, and removal rates for other processes followed the order ozone/BCM-GAC(62%) > ozone/BCM-silica gel(45%) > ozone/silica gel(43%) > ozone/Mn Loaded GAC(42%) > ozone alone(37%).

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.3
• /
• pp.75-78
• /
• 2010

In this study we investigated the electrical properties of ZnO-based MOS capacitor with $HfO_2$ as the gate dielectric. MIM capacitor, which uses either $HfO_2$ or $Al_2O_3$ as the dielectric layer, is also studied to understand the dependency of the dielectrics on the preparation conditions. It was found that thinner $HfO_2$ films yield better electrical properties, namely lower leakage current and higher breakdown electric field. These properties were observed to deteriorate when subsequently annealed. Capacitance in the depletion region of MOS capacitor was found to increase with UV ozone treatment time up to 60min. However, when the treatment time was extended to 120min, the trend is reversed. The 'threshold voltage' was also observed to positively shift with UV ozone treatment time up to 60min. The shift apparently saturated for longer treatment.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.1
• /
• pp.31-39
• /
• 2007

The objective of this study was to investigate the inactivation characteristics of Cryptosporidium oocysts by ozone and UV and to suggest the better, disinfection method. The inactivation CT value of 1 log(90%) and 2 log(99%) in of one disinfection, which is an index of disinfection for inactivation effect by ozone, were respectively 5.77 $mg{\cdot}min/L$ and 21.30 $mg{\cdot}min/L$. The inactivation in UV disinfection was not affected by pHs(5, 7 and 9), low turbidity(5 and below NTU) and UV intensity(0.2 and 0.6 $mWs/cm^2$) but obviously decreased at high turbidity over 20 NTU. Therefore UV disinfection capacity can be obtained when a good turbidity removal in drinking water treatment process is achieved. And if oocysts is exposed by high UV over 0.6 mWs/cm2 during enough time, the better inactivation effect will be obtained.

• Journal of Environmental Science International
• /
• v.16 no.4
• /
• pp.433-440
• /
• 2007

The photodegradation and by-products of the gaseous toluene with $TiO_2$ (P25) and short-wavelength UV ($UV_{254+185nm}$) radiation were studied. The toluene was decomposed and mineralized efficiently owed to the synergistic effect of photochemical oxidation in the gas phase and photocatalytic oxidation on the $TiO_2$ surface. The toluene by the $UV_{254+185nm}$ photoirradiated $TiO_2$ were mainly mineralized $CO_2$ and CO, but some water-soluble organic intermediates were also formed under severe reaction conditions. The ozone and secondary organic aerosol were produced as undesirable by-products. It was found that wet scrubber was useful as post-treatment to remove water-soluble organic intermediates. Excess ozone could be easily removed by means of a $MnO_2$ ozone-decomposition catalyst. It was also observed that the $MnO_2$ catalyst could decompose organic compounds by using oxygen reactive species formed in process of ozone decomposition.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.3
• /
• pp.63-69
• /
• 2012

Adhesion and mechanical reliability of silicon/epoxy/polyimide interfaces are critical issues for flexible electronics. Bonds between these interfaces are mainly hydrogen bonds, so their adhesion is weaker than cohesive fracture toughness and vulnerable to moisture. In order to enhance adhesion and suppress moisture-assisted debonding, UV/Ozone treatment and innovative sol-gel derived hybrid layers were applied to silicon/epoxy/polyimide interfaces. The fracture energy and subcritical crack growth rate were measured by using a double cantilever beam (DCB) fracture mechanics test. Results showed that UV/Ozone treatment increased the adhesion, but was not effective for improving reliability against humidity. However, by applying sol-gel derived hybrid layers, adhesion increase as well as suppresion of moisture-assisted cracking were achieved.

• Journal of Korean Society on Water Environment
• /
• v.20 no.2
• /
• pp.170-175
• /
• 2004

The purpose of this study was to monitor bacteria present in raw water and to investigate the effect of ozone, UV and combined ozone/UV processes for inactivating bacteria. Both polymerase chain reaction (PCR)-fragment length polymorphic analysis (PRA) and PCR-sequence analysis (PSA) were applied for the simultaneous analysis of numerous bacteria species present in each tested water, such as drinking water (DRW), drinking water source (DRWS) and sewage effluent water (SEW). According to the result, the number of detected bacteria species was zero in DRW, 58 in DRWS and 13 in SEW. After treatment of the each process, the ozone/UV process was the most successful for inactivating almost all bacteria. However, it was found that Flavobacterium sp., Pseudomonas sp. and Beta proteobacterium sp. had strong resistant to all tested processes, requiring further detailed study.